Hi Dongchun,
On Tue, Sep 10, 2019 at 09:04:46PM +0800, dongchun.zhu@xxxxxxxxxxxx wrote:
> From: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
>
> This patch mainly adds two more sensor modes for OV8856 CMOS image sensor.
> That is, the resolution of 1632*1224 and 3264*2448, corresponding to the bayer order of BGGR.
> The sensor revision also differs in some OTP register.
>
> Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
> ---
> drivers/media/i2c/ov8856.c | 654 +++++++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 639 insertions(+), 15 deletions(-)
>
> diff --git a/drivers/media/i2c/ov8856.c b/drivers/media/i2c/ov8856.c
> index cd347d6..9ad0b73 100644
> --- a/drivers/media/i2c/ov8856.c
> +++ b/drivers/media/i2c/ov8856.c
> @@ -1,12 +1,15 @@
> // SPDX-License-Identifier: GPL-2.0
> // Copyright (c) 2019 Intel Corporation.
>
> +#include <linux/clk.h>
> #include <asm/unaligned.h>
> #include <linux/acpi.h>
> #include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> #include <linux/i2c.h>
> #include <linux/module.h>
> #include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> #include <media/v4l2-ctrls.h>
> #include <media/v4l2-device.h>
> #include <media/v4l2-fwnode.h>
> @@ -18,10 +21,15 @@
> #define OV8856_LINK_FREQ_360MHZ 360000000ULL
> #define OV8856_LINK_FREQ_180MHZ 180000000ULL
> #define OV8856_SCLK 144000000ULL
> -#define OV8856_MCLK 19200000
> +#define OV8856_XVCLK 19200000
> +#define OV8856_XVCLK_TYP 24000000
How about calling these e.g. OV8856_XCLK_19_2 and OV8856_CLK_24? Or just
use the plain numbers; there's nothing really special about them.
Ideally you'd have both in a single location in the driver --- an array of
modes supported on each of them as they're different.
> #define OV8856_DATA_LANES 4
> #define OV8856_RGB_DEPTH 10
>
> +#define REG_X_ADDR_START 0x3808
> +#define X_OUTPUT_FULL_SIZE 0x0cc0
> +#define X_OUTPUT_BINNING_SIZE 0x0660
> +
> #define OV8856_REG_CHIP_ID 0x300a
> #define OV8856_CHIP_ID 0x00885a
>
> @@ -29,6 +37,22 @@
> #define OV8856_MODE_STANDBY 0x00
> #define OV8856_MODE_STREAMING 0x01
>
> +/* define 1B module revision */
> +#define OV8856_1B_MODULE 0x02
> +
> +/* the OTP read-out buffer is at 0x7000 and 0xf is the offset
> + * of the byte in the OTP that means the module revision
> + */
> +#define OV8856_MODULE_REVISION 0x700f
> +#define OV8856_OTP_MODE_CTRL 0x3d84
> +#define OV8856_OTP_LOAD_CTRL 0x3d81
> +#define OV8856_OTP_MODE_AUTO 0x00
> +#define OV8856_OTP_LOAD_CTRL_ENABLE BIT(0)
> +
> +/* Analog control register that decided by module revision */
> +#define OV8856_ANAL_MODE_CTRL 0x3614
> +#define OV8856_ANAL_1B_VAL 0x20
> +
> /* vertical-timings from sensor */
> #define OV8856_REG_VTS 0x380e
> #define OV8856_VTS_MAX 0x7fff
> @@ -64,6 +88,14 @@
>
> #define to_ov8856(_sd) container_of(_sd, struct ov8856, sd)
>
> +static const char * const ov8856_supply_names[] = {
> + "dovdd", /* Digital I/O power */
> + "avdd", /* Analog power */
> + "dvdd", /* Digital core power */
> +};
> +
> +#define OV8856_NUM_SUPPLIES ARRAY_SIZE(ov8856_supply_names)
> +
> enum {
> OV8856_LINK_FREQ_720MBPS,
> OV8856_LINK_FREQ_360MBPS,
> @@ -195,11 +227,11 @@ static const struct ov8856_reg mode_3280x2464_regs[] = {
> {0x3800, 0x00},
> {0x3801, 0x00},
> {0x3802, 0x00},
> - {0x3803, 0x06},
> + {0x3803, 0x07},
> {0x3804, 0x0c},
> {0x3805, 0xdf},
> {0x3806, 0x09},
> - {0x3807, 0xa7},
> + {0x3807, 0xa6},
This is changing an existing sensor mode. What are the effects of the
change?
Given that this register is not documented in the driver in any way, I'd
expect the commit message to carry some reasoning behind the change, also
suggesting it belongs to a separate patch. The same applies to changes to
the other existing modes.
> {0x3808, 0x0c},
> {0x3809, 0xd0},
> {0x380a, 0x09},
> @@ -211,7 +243,7 @@ static const struct ov8856_reg mode_3280x2464_regs[] = {
> {0x3810, 0x00},
> {0x3811, 0x00},
> {0x3812, 0x00},
> - {0x3813, 0x01},
> + {0x3813, 0x00},
> {0x3814, 0x01},
> {0x3815, 0x01},
> {0x3816, 0x00},
> @@ -316,6 +348,209 @@ static const struct ov8856_reg mode_3280x2464_regs[] = {
> {0x5e00, 0x00}
> };
>
> +static const struct ov8856_reg mode_3264x2448_regs[] = {
> + {0x0103, 0x01},
> + {0x0302, 0x3c},
> + {0x0303, 0x01},
> + {0x031e, 0x0c},
> + {0x3000, 0x20},
> + {0x3003, 0x08},
> + {0x300e, 0x20},
> + {0x3010, 0x00},
> + {0x3015, 0x84},
> + {0x3018, 0x72},
> + {0x3021, 0x23},
> + {0x3033, 0x24},
> + {0x3500, 0x00},
> + {0x3501, 0x9a},
> + {0x3502, 0x20},
> + {0x3503, 0x08},
> + {0x3505, 0x83},
> + {0x3508, 0x01},
> + {0x3509, 0x80},
> + {0x350c, 0x00},
> + {0x350d, 0x80},
> + {0x350e, 0x04},
> + {0x350f, 0x00},
> + {0x3510, 0x00},
> + {0x3511, 0x02},
> + {0x3512, 0x00},
> + {0x3600, 0x72},
> + {0x3601, 0x40},
> + {0x3602, 0x30},
> + {0x3610, 0xc5},
> + {0x3611, 0x58},
> + {0x3612, 0x5c},
> + {0x3613, 0xca},
> + {0x3614, 0x60},
> + {0x3628, 0xff},
> + {0x3629, 0xff},
> + {0x362a, 0xff},
> + {0x3633, 0x10},
> + {0x3634, 0x10},
> + {0x3635, 0x10},
> + {0x3636, 0x10},
> + {0x3663, 0x08},
> + {0x3669, 0x34},
> + {0x366d, 0x00},
> + {0x366e, 0x10},
> + {0x3706, 0x86},
> + {0x370b, 0x7e},
> + {0x3714, 0x23},
> + {0x3730, 0x12},
> + {0x3733, 0x10},
> + {0x3764, 0x00},
> + {0x3765, 0x00},
> + {0x3769, 0x62},
> + {0x376a, 0x2a},
> + {0x376b, 0x30},
> + {0x3780, 0x00},
> + {0x3781, 0x24},
> + {0x3782, 0x00},
> + {0x3783, 0x23},
> + {0x3798, 0x2f},
> + {0x37a1, 0x60},
> + {0x37a8, 0x6a},
> + {0x37ab, 0x3f},
> + {0x37c2, 0x04},
> + {0x37c3, 0xf1},
> + {0x37c9, 0x80},
> + {0x37cb, 0x16},
> + {0x37cc, 0x16},
> + {0x37cd, 0x16},
> + {0x37ce, 0x16},
> + {0x3800, 0x00},
> + {0x3801, 0x00},
> + {0x3802, 0x00},
> + {0x3803, 0x0c},
> + {0x3804, 0x0c},
> + {0x3805, 0xdf},
> + {0x3806, 0x09},
> + {0x3807, 0xa3},
> + {0x3808, 0x0c},
> + {0x3809, 0xc0},
> + {0x380a, 0x09},
> + {0x380b, 0x90},
> + {0x380c, 0x07},
> + {0x380d, 0x8c},
> + {0x380e, 0x09},
> + {0x380f, 0xb2},
> + {0x3810, 0x00},
> + {0x3811, 0x04},
> + {0x3812, 0x00},
> + {0x3813, 0x02},
> + {0x3814, 0x01},
> + {0x3815, 0x01},
> + {0x3816, 0x00},
> + {0x3817, 0x00},
> + {0x3818, 0x00},
> + {0x3819, 0x00},
> + {0x3820, 0x80},
> + {0x3821, 0x46},
> + {0x382a, 0x01},
> + {0x382b, 0x01},
> + {0x3830, 0x06},
> + {0x3836, 0x02},
> + {0x3862, 0x04},
> + {0x3863, 0x08},
> + {0x3cc0, 0x33},
> + {0x3d85, 0x17},
> + {0x3d8c, 0x73},
> + {0x3d8d, 0xde},
> + {0x4001, 0xe0},
> + {0x4003, 0x40},
> + {0x4008, 0x00},
> + {0x4009, 0x0b},
> + {0x400a, 0x00},
> + {0x400b, 0x84},
> + {0x400f, 0x80},
> + {0x4010, 0xf0},
> + {0x4011, 0xff},
> + {0x4012, 0x02},
> + {0x4013, 0x01},
> + {0x4014, 0x01},
> + {0x4015, 0x01},
> + {0x4042, 0x00},
> + {0x4043, 0x80},
> + {0x4044, 0x00},
> + {0x4045, 0x80},
> + {0x4046, 0x00},
> + {0x4047, 0x80},
> + {0x4048, 0x00},
> + {0x4049, 0x80},
> + {0x4041, 0x03},
> + {0x404c, 0x20},
> + {0x404d, 0x00},
> + {0x404e, 0x20},
> + {0x4203, 0x80},
> + {0x4307, 0x30},
> + {0x4317, 0x00},
> + {0x4502, 0x50},
> + {0x4503, 0x08},
> + {0x4601, 0x80},
> + {0x4800, 0x44},
> + {0x4816, 0x53},
> + {0x481b, 0x50},
> + {0x481f, 0x27},
> + {0x4823, 0x3c},
> + {0x482b, 0x00},
> + {0x4831, 0x66},
> + {0x4837, 0x16},
> + {0x483c, 0x0f},
> + {0x484b, 0x05},
> + {0x5000, 0x77},
> + {0x5001, 0x0a},
> + {0x5003, 0xc8},
> + {0x5004, 0x04},
> + {0x5006, 0x00},
> + {0x5007, 0x00},
> + {0x502e, 0x03},
> + {0x5030, 0x41},
> + {0x5780, 0x14},
> + {0x5781, 0x0f},
> + {0x5782, 0x44},
> + {0x5783, 0x02},
> + {0x5784, 0x01},
> + {0x5785, 0x01},
> + {0x5786, 0x00},
> + {0x5787, 0x04},
> + {0x5788, 0x02},
> + {0x5789, 0x0f},
> + {0x578a, 0xfd},
> + {0x578b, 0xf5},
> + {0x578c, 0xf5},
> + {0x578d, 0x03},
> + {0x578e, 0x08},
> + {0x578f, 0x0c},
> + {0x5790, 0x08},
> + {0x5791, 0x04},
> + {0x5792, 0x00},
> + {0x5793, 0x52},
> + {0x5794, 0xa3},
> + {0x5795, 0x02},
> + {0x5796, 0x20},
> + {0x5797, 0x20},
> + {0x5798, 0xd5},
> + {0x5799, 0xd5},
> + {0x579a, 0x00},
> + {0x579b, 0x50},
> + {0x579c, 0x00},
> + {0x579d, 0x2c},
> + {0x579e, 0x0c},
> + {0x579f, 0x40},
> + {0x57a0, 0x09},
> + {0x57a1, 0x40},
> + {0x59f8, 0x3d},
> + {0x5a08, 0x02},
> + {0x5b00, 0x02},
> + {0x5b01, 0x10},
> + {0x5b02, 0x03},
> + {0x5b03, 0xcf},
> + {0x5b05, 0x6c},
> + {0x5e00, 0x00},
> + {0x5e10, 0xfc}
> +};
> +
> static const struct ov8856_reg mode_1640x1232_regs[] = {
> {0x3000, 0x20},
> {0x3003, 0x08},
> @@ -385,11 +620,11 @@ static const struct ov8856_reg mode_1640x1232_regs[] = {
> {0x3800, 0x00},
> {0x3801, 0x00},
> {0x3802, 0x00},
> - {0x3803, 0x06},
> + {0x3803, 0x07},
> {0x3804, 0x0c},
> {0x3805, 0xdf},
> {0x3806, 0x09},
> - {0x3807, 0xa7},
> + {0x3807, 0xa6},
> {0x3808, 0x06},
> {0x3809, 0x68},
> {0x380a, 0x04},
> @@ -401,7 +636,7 @@ static const struct ov8856_reg mode_1640x1232_regs[] = {
> {0x3810, 0x00},
> {0x3811, 0x00},
> {0x3812, 0x00},
> - {0x3813, 0x01},
> + {0x3813, 0x00},
> {0x3814, 0x03},
> {0x3815, 0x01},
> {0x3816, 0x00},
> @@ -506,6 +741,209 @@ static const struct ov8856_reg mode_1640x1232_regs[] = {
> {0x5e00, 0x00}
> };
>
> +static const struct ov8856_reg mode_1632x1224_regs[] = {
> + {0x0103, 0x01},
> + {0x0302, 0x3c},
> + {0x0303, 0x01},
> + {0x031e, 0x0c},
> + {0x3000, 0x20},
> + {0x3003, 0x08},
> + {0x300e, 0x20},
> + {0x3010, 0x00},
> + {0x3015, 0x84},
> + {0x3018, 0x72},
> + {0x3021, 0x23},
> + {0x3033, 0x24},
> + {0x3500, 0x00},
> + {0x3501, 0x4c},
> + {0x3502, 0xe0},
> + {0x3503, 0x08},
> + {0x3505, 0x83},
> + {0x3508, 0x01},
> + {0x3509, 0x80},
> + {0x350c, 0x00},
> + {0x350d, 0x80},
> + {0x350e, 0x04},
> + {0x350f, 0x00},
> + {0x3510, 0x00},
> + {0x3511, 0x02},
> + {0x3512, 0x00},
> + {0x3600, 0x72},
> + {0x3601, 0x40},
> + {0x3602, 0x30},
> + {0x3610, 0xc5},
> + {0x3611, 0x58},
> + {0x3612, 0x5c},
> + {0x3613, 0xca},
> + {0x3614, 0x60},
> + {0x3628, 0xff},
> + {0x3629, 0xff},
> + {0x362a, 0xff},
> + {0x3633, 0x10},
> + {0x3634, 0x10},
> + {0x3635, 0x10},
> + {0x3636, 0x10},
> + {0x3663, 0x08},
> + {0x3669, 0x34},
> + {0x366d, 0x00},
> + {0x366e, 0x08},
> + {0x3706, 0x86},
> + {0x370b, 0x7e},
> + {0x3714, 0x27},
> + {0x3730, 0x12},
> + {0x3733, 0x10},
> + {0x3764, 0x00},
> + {0x3765, 0x00},
> + {0x3769, 0x62},
> + {0x376a, 0x2a},
> + {0x376b, 0x30},
> + {0x3780, 0x00},
> + {0x3781, 0x24},
> + {0x3782, 0x00},
> + {0x3783, 0x23},
> + {0x3798, 0x2f},
> + {0x37a1, 0x60},
> + {0x37a8, 0x6a},
> + {0x37ab, 0x3f},
> + {0x37c2, 0x14},
> + {0x37c3, 0xf1},
> + {0x37c9, 0x80},
> + {0x37cb, 0x16},
> + {0x37cc, 0x16},
> + {0x37cd, 0x16},
> + {0x37ce, 0x16},
> + {0x3800, 0x00},
> + {0x3801, 0x00},
> + {0x3802, 0x00},
> + {0x3803, 0x0c},
> + {0x3804, 0x0c},
> + {0x3805, 0xdf},
> + {0x3806, 0x09},
> + {0x3807, 0xa3},
> + {0x3808, 0x06},
> + {0x3809, 0x60},
> + {0x380a, 0x04},
> + {0x380b, 0xc8},
> + {0x380c, 0x07},
> + {0x380d, 0x8c},
> + {0x380e, 0x09},
> + {0x380f, 0xb2},
> + {0x3810, 0x00},
> + {0x3811, 0x02},
> + {0x3812, 0x00},
> + {0x3813, 0x02},
> + {0x3814, 0x03},
> + {0x3815, 0x01},
> + {0x3816, 0x00},
> + {0x3817, 0x00},
> + {0x3818, 0x00},
> + {0x3819, 0x00},
> + {0x3820, 0x80},
> + {0x3821, 0x47},
> + {0x382a, 0x03},
> + {0x382b, 0x01},
> + {0x3830, 0x06},
> + {0x3836, 0x02},
> + {0x3862, 0x04},
> + {0x3863, 0x08},
> + {0x3cc0, 0x33},
> + {0x3d85, 0x17},
> + {0x3d8c, 0x73},
> + {0x3d8d, 0xde},
> + {0x4001, 0xe0},
> + {0x4003, 0x40},
> + {0x4008, 0x00},
> + {0x4009, 0x05},
> + {0x400a, 0x00},
> + {0x400b, 0x84},
> + {0x400f, 0x80},
> + {0x4010, 0xf0},
> + {0x4011, 0xff},
> + {0x4012, 0x02},
> + {0x4013, 0x01},
> + {0x4014, 0x01},
> + {0x4015, 0x01},
> + {0x4042, 0x00},
> + {0x4043, 0x80},
> + {0x4044, 0x00},
> + {0x4045, 0x80},
> + {0x4046, 0x00},
> + {0x4047, 0x80},
> + {0x4048, 0x00},
> + {0x4049, 0x80},
> + {0x4041, 0x03},
> + {0x404c, 0x20},
> + {0x404d, 0x00},
> + {0x404e, 0x20},
> + {0x4203, 0x80},
> + {0x4307, 0x30},
> + {0x4317, 0x00},
> + {0x4502, 0x50},
> + {0x4503, 0x08},
> + {0x4601, 0x80},
> + {0x4800, 0x44},
> + {0x4816, 0x53},
> + {0x481b, 0x50},
> + {0x481f, 0x27},
> + {0x4823, 0x3c},
> + {0x482b, 0x00},
> + {0x4831, 0x66},
> + {0x4837, 0x16},
> + {0x483c, 0x0f},
> + {0x484b, 0x05},
> + {0x5000, 0x77},
> + {0x5001, 0x0a},
> + {0x5003, 0xc8},
> + {0x5004, 0x04},
> + {0x5006, 0x00},
> + {0x5007, 0x00},
> + {0x502e, 0x03},
> + {0x5030, 0x41},
> + {0x5795, 0x00},
> + {0x5796, 0x10},
> + {0x5797, 0x10},
> + {0x5798, 0x73},
> + {0x5799, 0x73},
> + {0x579a, 0x00},
> + {0x579b, 0x28},
> + {0x579c, 0x00},
> + {0x579d, 0x16},
> + {0x579e, 0x06},
> + {0x579f, 0x20},
> + {0x57a0, 0x04},
> + {0x57a1, 0xa0},
> + {0x5780, 0x14},
> + {0x5781, 0x0f},
> + {0x5782, 0x44},
> + {0x5783, 0x02},
> + {0x5784, 0x01},
> + {0x5785, 0x01},
> + {0x5786, 0x00},
> + {0x5787, 0x04},
> + {0x5788, 0x02},
> + {0x5789, 0x0f},
> + {0x578a, 0xfd},
> + {0x578b, 0xf5},
> + {0x578c, 0xf5},
> + {0x578d, 0x03},
> + {0x578e, 0x08},
> + {0x578f, 0x0c},
> + {0x5790, 0x08},
> + {0x5791, 0x04},
> + {0x5792, 0x00},
> + {0x5793, 0x52},
> + {0x5794, 0xa3},
> + {0x59f8, 0x3d},
> + {0x5a08, 0x02},
> + {0x5b00, 0x02},
> + {0x5b01, 0x10},
> + {0x5b02, 0x03},
> + {0x5b03, 0xcf},
> + {0x5b05, 0x6c},
> + {0x5e00, 0x00},
> + {0x5e10, 0xfc}
> +};
> +
> static const char * const ov8856_test_pattern_menu[] = {
> "Disabled",
> "Standard Color Bar",
> @@ -548,6 +986,18 @@ static const struct ov8856_mode supported_modes[] = {
> .link_freq_index = OV8856_LINK_FREQ_720MBPS,
> },
> {
> + .width = 3264,
> + .height = 2448,
> + .hts = 1932,
> + .vts_def = 2482,
> + .vts_min = 2482,
> + .reg_list = {
> + .num_of_regs = ARRAY_SIZE(mode_3264x2448_regs),
> + .regs = mode_3264x2448_regs,
> + },
> + .link_freq_index = OV8856_LINK_FREQ_720MBPS,
> + },
How do you guarantee that the modes are only used on the xvclk frequency
they're intended for?
I think it'd be best if you added the new modes in a separete patch.
> + {
> .width = 1640,
> .height = 1232,
> .hts = 3820,
> @@ -558,6 +1008,18 @@ static const struct ov8856_mode supported_modes[] = {
> .regs = mode_1640x1232_regs,
> },
> .link_freq_index = OV8856_LINK_FREQ_360MBPS,
> + },
> + {
> + .width = 1632,
> + .height = 1224,
> + .hts = 1932,
> + .vts_def = 2482,
> + .vts_min = 2482,
> + .reg_list = {
> + .num_of_regs = ARRAY_SIZE(mode_1632x1224_regs),
> + .regs = mode_1632x1224_regs,
> + },
> + .link_freq_index = OV8856_LINK_FREQ_360MBPS,
> }
> };
>
> @@ -566,16 +1028,28 @@ struct ov8856 {
> struct media_pad pad;
> struct v4l2_ctrl_handler ctrl_handler;
>
> + struct clk *xvclk;
> + struct gpio_desc *n_shutdn_gpio;
> + struct regulator_bulk_data supplies[OV8856_NUM_SUPPLIES];
> +
> /* V4L2 Controls */
> struct v4l2_ctrl *link_freq;
> struct v4l2_ctrl *pixel_rate;
> struct v4l2_ctrl *vblank;
> struct v4l2_ctrl *hblank;
> struct v4l2_ctrl *exposure;
> + struct v4l2_mbus_framefmt fmt;
>
> /* Current mode */
> const struct ov8856_mode *cur_mode;
>
> + /* module hardware version that can be read out from register 0x700f
> + * the register value corresponds to different hardware version
> + * 01: 2A module revision
> + * 02: 1B module revision
> + */
> + bool is_1B_revision;
> +
> /* To serialize asynchronus callbacks */
> struct mutex mutex;
>
> @@ -696,6 +1170,25 @@ static int ov8856_test_pattern(struct ov8856 *ov8856, u32 pattern)
> OV8856_REG_VALUE_08BIT, pattern);
> }
>
> +static int ov8856_check_revision(struct ov8856 *ov8856)
> +{
> + int ret;
> +
> + ret = ov8856_write_reg(ov8856, OV8856_REG_MODE_SELECT,
> + OV8856_REG_VALUE_08BIT, OV8856_MODE_STREAMING);
> + if (ret)
> + return ret;
> +
> + ret = ov8856_write_reg(ov8856, OV8856_OTP_MODE_CTRL,
> + OV8856_REG_VALUE_08BIT, OV8856_OTP_MODE_AUTO);
> + if (ret)
> + return ret;
> +
> + return ov8856_write_reg(ov8856, OV8856_OTP_LOAD_CTRL,
> + OV8856_REG_VALUE_08BIT,
> + OV8856_OTP_LOAD_CTRL_ENABLE);
Is it not necessary to disable streaming after reading EEPROM?
> +}
> +
> static int ov8856_set_ctrl(struct v4l2_ctrl *ctrl)
> {
> struct ov8856 *ov8856 = container_of(ctrl->handler,
> @@ -825,7 +1318,6 @@ static void ov8856_update_pad_format(const struct ov8856_mode *mode,
> {
> fmt->width = mode->width;
> fmt->height = mode->height;
> - fmt->code = MEDIA_BUS_FMT_SGRBG10_1X10;
> fmt->field = V4L2_FIELD_NONE;
> }
>
> @@ -834,6 +1326,7 @@ static int ov8856_start_streaming(struct ov8856 *ov8856)
> struct i2c_client *client = v4l2_get_subdevdata(&ov8856->sd);
> const struct ov8856_reg_list *reg_list;
> int link_freq_index, ret;
> + u32 h_size;
>
> link_freq_index = ov8856->cur_mode->link_freq_index;
> reg_list = &link_freq_configs[link_freq_index].reg_list;
> @@ -850,6 +1343,29 @@ static int ov8856_start_streaming(struct ov8856 *ov8856)
> return ret;
> }
>
> + /* Update R3614 if the revision is 1B module */
> + if (ov8856->is_1B_revision) {
> + ret = ov8856_write_reg(ov8856, OV8856_ANAL_MODE_CTRL,
> + OV8856_REG_VALUE_08BIT,
> + OV8856_ANAL_1B_VAL);
> + if (ret) {
> + dev_err(&client->dev, "failed to set R3614");
> + return ret;
> + }
> + }
> +
> + ret = ov8856_read_reg(ov8856, REG_X_ADDR_START,
> + OV8856_REG_VALUE_16BIT, &h_size);
> + if (ret) {
> + dev_err(&client->dev, "failed to read out R3614");
> + return ret;
> + }
> +
> + if (h_size == X_OUTPUT_FULL_SIZE || h_size == X_OUTPUT_BINNING_SIZE)
> + ov8856->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
I wonder if this condition is right. The pixel order (and thus the media
bus code) is determined by cropping (and flipping and mirroring, but
they're not supported right now). See e.g. the smiapp driver for an
example.
The correct media bus code needs to be available to the user through the
regular API at all times, not only after streaming is started.
I'd suggest adding support for other pixel orders in a separate patch.
> +
> ret = __v4l2_ctrl_handler_setup(ov8856->sd.ctrl_handler);
> if (ret)
> return ret;
> @@ -878,6 +1394,7 @@ static int ov8856_set_stream(struct v4l2_subdev *sd, int enable)
> struct ov8856 *ov8856 = to_ov8856(sd);
> struct i2c_client *client = v4l2_get_subdevdata(sd);
> int ret = 0;
> + u32 val;
>
> if (ov8856->streaming == enable)
> return 0;
> @@ -908,6 +1425,44 @@ static int ov8856_set_stream(struct v4l2_subdev *sd, int enable)
> return ret;
> }
>
> +static int __ov8856_power_on(struct ov8856 *ov8856)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov8856->sd);
> + int ret;
> +
> + ret = clk_prepare_enable(ov8856->xvclk);
> + if (ret < 0) {
> + dev_err(&client->dev, "failed to enable xvclk\n");
> + return ret;
> + }
> +
> + gpiod_set_value_cansleep(ov8856->n_shutdn_gpio, GPIOD_OUT_LOW);
> +
> + ret = regulator_bulk_enable(OV8856_NUM_SUPPLIES, ov8856->supplies);
> + if (ret < 0) {
> + dev_err(&client->dev, "failed to enable regulators\n");
> + goto disable_clk;
> + }
> +
> + gpiod_set_value_cansleep(ov8856->n_shutdn_gpio, GPIOD_OUT_HIGH);
..., 1);
> +
> + usleep_range(1400, 1500);
> +
> + return 0;
> +
> +disable_clk:
> + clk_disable_unprepare(ov8856->xvclk);
How about the n_shutdn GPIO?
> +
> + return ret;
> +}
> +
> +static void __ov8856_power_off(struct ov8856 *ov8856)
> +{
> + gpiod_set_value_cansleep(ov8856->n_shutdn_gpio, 1);
Why to inactivate xshutdn here (it already was)?
> + regulator_bulk_disable(OV8856_NUM_SUPPLIES, ov8856->supplies);
> + clk_disable_unprepare(ov8856->xvclk);
> +}
> +
> static int __maybe_unused ov8856_suspend(struct device *dev)
> {
> struct i2c_client *client = to_i2c_client(dev);
> @@ -951,6 +1506,7 @@ static int ov8856_set_format(struct v4l2_subdev *sd,
> struct v4l2_subdev_format *fmt)
> {
> struct ov8856 *ov8856 = to_ov8856(sd);
> + struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> const struct ov8856_mode *mode;
> s32 vblank_def, h_blank;
>
> @@ -960,7 +1516,9 @@ static int ov8856_set_format(struct v4l2_subdev *sd,
> fmt->format.height);
>
> mutex_lock(&ov8856->mutex);
> - ov8856_update_pad_format(mode, &fmt->format);
> + mbus_fmt->code = ov8856->fmt.code;
> + ov8856_update_pad_format(mode, mbus_fmt);
> + ov8856->fmt = fmt->format;
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> *v4l2_subdev_get_try_format(sd, cfg, fmt->pad) = fmt->format;
> } else {
> @@ -992,13 +1550,17 @@ static int ov8856_get_format(struct v4l2_subdev *sd,
> struct v4l2_subdev_format *fmt)
> {
> struct ov8856 *ov8856 = to_ov8856(sd);
> + struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
>
> mutex_lock(&ov8856->mutex);
> - if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
> + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> fmt->format = *v4l2_subdev_get_try_format(&ov8856->sd, cfg,
> fmt->pad);
> - else
> - ov8856_update_pad_format(ov8856->cur_mode, &fmt->format);
> + } else {
> + fmt->format = ov8856->fmt;
> + ov8856_update_pad_format(ov8856->cur_mode, mbus_fmt);
> + mbus_fmt->code = ov8856->fmt.code;
> + }
>
> mutex_unlock(&ov8856->mutex);
>
> @@ -1009,11 +1571,12 @@ static int ov8856_enum_mbus_code(struct v4l2_subdev *sd,
> struct v4l2_subdev_pad_config *cfg,
> struct v4l2_subdev_mbus_code_enum *code)
> {
> - /* Only one bayer order GRBG is supported */
> + struct ov8856 *ov8856 = to_ov8856(sd);
> +
> if (code->index > 0)
> return -EINVAL;
>
> - code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
> + code->code = ov8856->fmt.code;
>
> return 0;
> }
> @@ -1089,6 +1652,20 @@ static int ov8856_identify_module(struct ov8856 *ov8856)
> return -ENXIO;
> }
>
> + /* check sensor hardware revision */
> + ret = ov8856_check_revision(ov8856);
> + if (ret) {
> + dev_err(&client->dev, "failed to check sensor revision");
> + return ret;
> + }
> +
> + ret = ov8856_read_reg(ov8856, OV8856_MODULE_REVISION,
> + OV8856_REG_VALUE_08BIT, &val);
> + if (ret)
> + return ret;
> +
> + ov8856->is_1B_revision = (val == OV8856_1B_MODULE) ? 1 : 0;
> +
> return 0;
> }
>
> @@ -1107,7 +1684,7 @@ static int ov8856_check_hwcfg(struct device *dev)
> return -ENXIO;
>
> fwnode_property_read_u32(fwnode, "clock-frequency", &mclk);
> - if (mclk != OV8856_MCLK) {
> + if (mclk != OV8856_XVCLK) {
> dev_err(dev, "external clock %d is not supported", mclk);
> return -EINVAL;
> }
> @@ -1164,6 +1741,9 @@ static int ov8856_remove(struct i2c_client *client)
> media_entity_cleanup(&sd->entity);
> v4l2_ctrl_handler_free(sd->ctrl_handler);
> pm_runtime_disable(&client->dev);
> + if (!pm_runtime_status_suspended(&client->dev))
> + __ov8856_power_off(ov8856);
> + pm_runtime_set_suspended(&client->dev);
> mutex_destroy(&ov8856->mutex);
>
> return 0;
> @@ -1172,6 +1752,7 @@ static int ov8856_remove(struct i2c_client *client)
> static int ov8856_probe(struct i2c_client *client)
> {
> struct ov8856 *ov8856;
> + unsigned int i;
> int ret;
>
> ret = ov8856_check_hwcfg(&client->dev);
> @@ -1186,6 +1767,42 @@ static int ov8856_probe(struct i2c_client *client)
> return -ENOMEM;
>
> v4l2_i2c_subdev_init(&ov8856->sd, client, &ov8856_subdev_ops);
> + ov8856->fmt.code = MEDIA_BUS_FMT_SGRBG10_1X10;
> +
> + ov8856->xvclk = devm_clk_get(&client->dev, "xvclk");
Does this work on ACPI?
See e.g. the smiapp driver for an example. The same applies to the rest of
the chunk.
> + if (IS_ERR(ov8856->xvclk)) {
> + dev_err(&client->dev, "failed to get xvclk\n");
> + return -EINVAL;
> + }
> +
> + ret = clk_set_rate(ov8856->xvclk, OV8856_XVCLK_TYP);
> + if (ret < 0) {
> + dev_err(&client->dev, "failed to set xvclk rate (24MHz)\n");
> + return ret;
> + }
> + if (clk_get_rate(ov8856->xvclk) != OV8856_XVCLK_TYP)
> + dev_warn(&client->dev,
> + "xvclk mismatched, modes are based on 24MHz\n");
> +
> + ov8856->n_shutdn_gpio = devm_gpiod_get(&client->dev, "reset",
> + GPIOD_OUT_LOW);
> + if (IS_ERR(ov8856->n_shutdn_gpio)) {
> + dev_err(&client->dev, "failed to get reset-gpios\n");
> + return -EINVAL;
> + }
> +
> + for (i = 0; i < OV8856_NUM_SUPPLIES; i++)
> + ov8856->supplies[i].supply = ov8856_supply_names[i];
> +
> + ret = devm_regulator_bulk_get(&client->dev, OV8856_NUM_SUPPLIES,
> + ov8856->supplies);
> + if (ret)
> + dev_warn(&client->dev, "failed to get regulators\n");
> +
> + ret = __ov8856_power_on(ov8856);
> + if (ret)
> + dev_warn(&client->dev, "failed to power on\n");
> +
> ret = ov8856_identify_module(ov8856);
> if (ret) {
> dev_err(&client->dev, "failed to find sensor: %d", ret);
> @@ -1251,11 +1868,18 @@ static const struct acpi_device_id ov8856_acpi_ids[] = {
> MODULE_DEVICE_TABLE(acpi, ov8856_acpi_ids);
> #endif
>
> +static const struct of_device_id ov8856_of_match[] = {
> + { .compatible = "ovti,ov8856" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ov8856_of_match);
> +
> static struct i2c_driver ov8856_i2c_driver = {
> .driver = {
> .name = "ov8856",
> .pm = &ov8856_pm_ops,
> .acpi_match_table = ACPI_PTR(ov8856_acpi_ids),
> + .of_match_table = ov8856_of_match,
> },
> .probe_new = ov8856_probe,
> .remove = ov8856_remove,
--
Regards,
Sakari Ailus
sakari.ailus@xxxxxxxxxxxxxxx
