Hi, On 2019-08-29 13:43:49 +0200, Hans Verkuil wrote: > Adding Niklas. > > Niklas, can you take a look at this? I'm happy to have a look at this. I'm currently moving so all my boards are in a box somewhere. I hope to have my lab up and running next week, so if this is not urgent I will look at it then. > > Regards, > > Hans > > On 8/27/19 11:55 PM, Matthew Michilot wrote: > > From: Matthew Michilot <matthew.michilot@xxxxxxxxx> > > > > Captured video would be out of sync when using the adv7280 with > > the BT.656-4 protocol. Certain registers (0x04, 0x31, 0xE6) had to > > be configured properly to ensure BT.656-4 compatibility. > > > > An error in the adv7280 reference manual suggested that EAV/SAV mode > > was enabled by default, however upon inspecting register 0x31, it was > > determined to be disabled by default. > > > > Signed-off-by: Matthew Michilot <matthew.michilot@xxxxxxxxx> > > Reviewed-by: Tim Harvey <tharvey@xxxxxxxxxxxxx> > > --- > > drivers/media/i2c/adv7180.c | 15 +++++++++++++-- > > 1 file changed, 13 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/media/i2c/adv7180.c b/drivers/media/i2c/adv7180.c > > index 99697baad2ea..27da424dce76 100644 > > --- a/drivers/media/i2c/adv7180.c > > +++ b/drivers/media/i2c/adv7180.c > > @@ -94,6 +94,7 @@ > > #define ADV7180_REG_SHAP_FILTER_CTL_1 0x0017 > > #define ADV7180_REG_CTRL_2 0x001d > > #define ADV7180_REG_VSYNC_FIELD_CTL_1 0x0031 > > +#define ADV7180_VSYNC_FIELD_CTL_1_NEWAV 0x12 > > #define ADV7180_REG_MANUAL_WIN_CTL_1 0x003d > > #define ADV7180_REG_MANUAL_WIN_CTL_2 0x003e > > #define ADV7180_REG_MANUAL_WIN_CTL_3 0x003f > > @@ -935,10 +936,20 @@ static int adv7182_init(struct adv7180_state *state) > > adv7180_write(state, ADV7180_REG_EXTENDED_OUTPUT_CONTROL, 0x57); > > adv7180_write(state, ADV7180_REG_CTRL_2, 0xc0); > > } else { > > - if (state->chip_info->flags & ADV7180_FLAG_V2) > > + if (state->chip_info->flags & ADV7180_FLAG_V2) { > > + /* ITU-R BT.656-4 compatible */ > > adv7180_write(state, > > ADV7180_REG_EXTENDED_OUTPUT_CONTROL, > > - 0x17); > > + ADV7180_EXTENDED_OUTPUT_CONTROL_NTSCDIS); > > + /* Manually set NEWAVMODE */ > > + adv7180_write(state, > > + ADV7180_REG_VSYNC_FIELD_CTL_1, > > + ADV7180_VSYNC_FIELD_CTL_1_NEWAV); > > + /* Manually set V bit end position in NTSC mode */ > > + adv7180_write(state, > > + ADV7180_REG_NTSC_V_BIT_END, > > + ADV7180_NTSC_V_BIT_END_MANUAL_NVEND); > > + } > > else > > adv7180_write(state, > > ADV7180_REG_EXTENDED_OUTPUT_CONTROL, > > > -- Regards, Niklas Söderlund