On Mon, Aug 26, 2019 at 5:38 PM Sakari Ailus
<sakari.ailus@xxxxxxxxxxxxxxx> wrote:
>
> Hi Tomasz,
>
> On Fri, Jun 07, 2019 at 04:54:06PM +0900, Tomasz Figa wrote:
> > On Wed, Jun 5, 2019 at 7:15 PM Sakari Ailus
> > <sakari.ailus@xxxxxxxxxxxxxxx> wrote:
> > >
> > > Hi Tomasz,
> > >
> > > On Wed, Jun 05, 2019 at 04:07:52PM +0900, Tomasz Figa wrote:
> > > > Hi Sakari,
> > > >
> > > > On Fri, May 10, 2019 at 01:09:28PM +0300, Sakari Ailus wrote:
> > > > > Tell ACPI device PM code that the driver supports the device being powered
> > > > > off when the driver's probe function is entered.
> > > > >
> > > > > Signed-off-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
> > > > > ---
> > > > > drivers/media/i2c/ov5670.c | 25 ++++++++++++++-----------
> > > > > 1 file changed, 14 insertions(+), 11 deletions(-)
> > > > >
> > > > > diff --git a/drivers/media/i2c/ov5670.c b/drivers/media/i2c/ov5670.c
> > > > > index 041fcbb4eebdf..57e8b92f90e09 100644
> > > > > --- a/drivers/media/i2c/ov5670.c
> > > > > +++ b/drivers/media/i2c/ov5670.c
> > > > > @@ -2444,6 +2444,7 @@ static int ov5670_probe(struct i2c_client *client)
> > > > > struct ov5670 *ov5670;
> > > > > const char *err_msg;
> > > > > u32 input_clk = 0;
> > > > > + bool powered_off;
> > > > > int ret;
> > > > >
> > > > > device_property_read_u32(&client->dev, "clock-frequency", &input_clk);
> > > > > @@ -2460,11 +2461,14 @@ static int ov5670_probe(struct i2c_client *client)
> > > > > /* Initialize subdev */
> > > > > v4l2_i2c_subdev_init(&ov5670->sd, client, &ov5670_subdev_ops);
> > > > >
> > > > > - /* Check module identity */
> > > > > - ret = ov5670_identify_module(ov5670);
> > > > > - if (ret) {
> > > > > - err_msg = "ov5670_identify_module() error";
> > > > > - goto error_print;
> > > > > + powered_off = acpi_dev_powered_off_for_probe(&client->dev);
> > > > > + if (!powered_off) {
> > > > > + /* Check module identity */
> > > > > + ret = ov5670_identify_module(ov5670);
> > > > > + if (ret) {
> > > > > + err_msg = "ov5670_identify_module() error";
> > > > > + goto error_print;
> > > > > + }
> > > > > }
> > > >
> > > > I don't like the fact that we can't detect any hardware connection issue
> > > > here anymore and we would actually get some obscure failure when we
> > > > actually start streaming.
> > > >
> > > > Wouldn't it be possible to still keep this behavior of not powering on
> > > > the device at boot-up if no driver is bound and then have this driver
> > > > built as a module and loaded later when the camera is to be used for the
> > > > first time after the system boots?
> > >
> > > That'd be a way to work around this, but the downside would be that the
> > > user space would need to know not only which drivers to load, but also
> > > which drivers _not_ to load. The user space could obtain the former from
> > > the kernel but not the latter, it'd be system specific configuration.
> > >
> > > Moving the responsibility of loading the driver to user space would also
> > > not address figuring out whether the sensor is accessible through its
> > > control bus: you have to power it on to do that. In fact, if you want to be
> > > sure that the hardware is all right, you have to start streaming on the
> > > device first and that is not a part of a typical driver initialisation
> > > sequence. Just checking the sensor is accessible over I涎 is not enough.
> > >
> > > The proposed solution addresses the problem without user space changes.
> >
> > I guess that makes sense indeed. If going this way, why not just move
> > all the hardware access from probe to streamon and avoid any
> > conditional checks at all?
>
> My apologies for the late answer.
>
> In that case there would be no way to verify the hardware actually is
> there, even on systems where there is no adverse effect from doing that.
> For a sensor driver this could be just fine, but I have doubts it'd be
> appropriate for e.g. the at24 driver.
For an eeprom, the first read could fail. That said, I agree that for
systems on which there is no such concern it would still be desirable
to check if the device is accessible in probe.
Anyway, I think you convinced me. :)
Reviewed-by: Tomasz Figa <tfiga@xxxxxxxxxxxx>
Best regards,
Tomasz
