On Wed, Aug 07, 2019 at 08:48:00PM +0800, Jungo Lin wrote:
> This patch adds DT binding document for the Pass 1 (P1) unit
> in Mediatek's camera ISP system. The Pass 1 unit grabs the sensor
> data out from the sensor interface, applies ISP image effects
> from tuning data and outputs the image data or statistics data to DRAM.
>
> Signed-off-by: Jungo Lin <jungo.lin@xxxxxxxxxxxx>
> ---
> .../bindings/media/mediatek,camisp.txt | 73 +++++++++++++++++++
> 1 file changed, 73 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/mediatek,camisp.txt
>
> diff --git a/Documentation/devicetree/bindings/media/mediatek,camisp.txt b/Documentation/devicetree/bindings/media/mediatek,camisp.txt
> new file mode 100644
> index 000000000000..fa2713acceca
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/mediatek,camisp.txt
> @@ -0,0 +1,73 @@
> +* Mediatek Image Signal Processor Pass 1 (ISP P1)
> +
> +The Pass 1 unit of Mediatek's camera ISP system grabs the sensor data out
> +from the sensor interface, applies ISP effects from tuning data and outputs
> +the image data and statistics data to DRAM. Furthermore, Pass 1 unit has
> +the ability to output two different resolutions frames at the same time to
> +increase the performance of the camera application.
> +
> +Required properties:
> +- compatible: Must be "mediatek,mt8183-camisp" for MT8183.
> +- reg: Physical base address of the camera function block register and
> + length of memory mapped region. Must contain an entry for each entry
> + in reg-names.
> +- reg-names: Must include the following entries:
> + "cam_sys": Camera base function block
> + "cam_uni": Camera UNI function block
> + "cam_a": Camera ISP P1 hardware unit A
> + "cam_b": Camera ISP P1 hardware unit B
> + "cam_c": Camera ISP P1 hardware unit C
> +- interrupts: Must contain an entry for each entry in interrupt-names.
> +- interrupt-names : Must include the following entries:
> + "cam_uni": Camera UNI interrupt
> + "cam_a": Camera unit A interrupt
> + "cam_b": Camera unit B interrupt
> + "cam_c": Camera unit C interrupt
> +- iommus: Shall point to the respective IOMMU block with master port
> + as argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
> + for details.
> +- clocks: A list of phandle and clock specifier pairs as listed
> + in clock-names property, see
> + Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
> +- clock-names: Must be "camsys_cam_cgpdn" and "camsys_camtg_cgpdn".
> +- mediatek,larb: Must contain the local arbiters in the current SoCs, see
> + Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
> + for details.
> +- power-domains: a phandle to the power domain, see
> + Documentation/devicetree/bindings/power/power_domain.txt for details.
> +- mediatek,scp : The node of system control processor (SCP), see
> + Documentation/devicetree/bindings/remoteproc/mtk,scp.txt for details.
> +
> +Example:
> +SoC specific DT entry:
> +
> + camisp: camisp@1a000000 {
Also, you can remove 2 levels of indentation here.
> + compatible = "mediatek,mt8183-camisp", "syscon";
> + reg = <0 0x1a000000 0 0x1000>,
> + <0 0x1a003000 0 0x1000>,
> + <0 0x1a004000 0 0x2000>,
> + <0 0x1a006000 0 0x2000>,
> + <0 0x1a008000 0 0x2000>;
> + reg-names = "cam_sys",
> + "cam_uni",
> + "cam_a",
> + "cam_b",
> + "cam_c";
> + interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 254 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 255 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 256 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-names = "cam_uni",
> + "cam_a",
> + "cam_b",
> + "cam_c";
> + iommus = <&iommu M4U_PORT_CAM_IMGO>;
> + clocks = <&camsys CLK_CAM_CAM>,
> + <&camsys CLK_CAM_CAMTG>;
> + clock-names = "camsys_cam_cgpdn",
> + "camsys_camtg_cgpdn";
> + mediatek,larb = <&larb3>,
> + <&larb6>;
> + power-domains = <&scpsys MT8183_POWER_DOMAIN_CAM>;
> + mediatek,scp = <&scp>;
> + };
> --
> 2.18.0
>
