Hi Sakari,
gentle ping.
Regards,
Marco
On 19-07-29 12:40, Marco Felsch wrote:
> Hi Sakari,
>
> On 19-06-25 15:27, Sakari Ailus wrote:
> > Hi Marco,
> >
> > Thanks for the set.
> >
> > Looks quite good to me in general; a few minor comments below.
>
> Sorry for the delayed response.
>
> > On Wed, Jun 19, 2019 at 05:28:38PM +0200, Marco Felsch wrote:
> > > Adding support for the TC358746 bridge. The Bridge can receive images on
> > > the parallel input port and send it to the host using the CSI-TX unit.
> > > Furthermore the Bridge can receive images from the host using the CSI-RX
> > > unit and send it to the parallel output port.
> > >
> > > Currently the only the first case is implemented and tested. The bridge
> > > driver needs two information from the connected sensor: hblank time and
> > > pixel-rate. Both information are requested using the v4l2_ctrl interface.
> > > The driver won't create a media-link if one or both information are
> > > missing.
> > >
> > > Missing feature:
> > > - Provide mclk on GPIO[0]
> > > - Sending pictures from the host to a parallel display
> > > - v4l_event support
> > >
> > > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>
> > > ---
> > > Changes
> > > v2:
> > > - adapt Kconfig symbole description
> > > - reorder includes alphabetical
> > > - drop refclk input-clock is named 'refclk'
> > > - fix module license to GPL v2
> > > - use unsigned int for zero-based count vars
> > > - use unsigned int for width parameter in tc358746_adjust_fifo_size()
> > > tc358746_adjust_timings()
> > > - use unsgined int for state->link_freq local variables since that
> > > can't be negative
> > > - drop tc358746_g_mbus_config() since it will be removed soon
> > > - store the sensor_pclk_ctrl and sensor_hblank_ctrl references to
> > > request the ctrl's only once.
> > > - replace dev_*() by v4l2_*() macros
> > > - move to probe_new() and drop i2c_device_id table
> > > - improve error path during probe()
> > > - change i2c_wr16_and_or() logic so the user only have to specify the
> > > mask. This avoids build warnings due to '-Woverflow' compilations.
> > > The bug was found by the kbuild test robot.
> > >
> > > drivers/media/i2c/Kconfig | 12 +
> > > drivers/media/i2c/Makefile | 1 +
> > > drivers/media/i2c/tc358746.c | 1807 +++++++++++++++++++++++++++++
> > > drivers/media/i2c/tc358746_regs.h | 208 ++++
> > > 4 files changed, 2028 insertions(+)
> > > create mode 100644 drivers/media/i2c/tc358746.c
> > > create mode 100644 drivers/media/i2c/tc358746_regs.h
> > >
> > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> > > index cb8db944aa41..454d8f682126 100644
> > > --- a/drivers/media/i2c/Kconfig
> > > +++ b/drivers/media/i2c/Kconfig
> > > @@ -360,6 +360,18 @@ config VIDEO_TC358743_CEC
> > > When selected the tc358743 will support the optional
> > > HDMI CEC feature.
> > >
> > > +config VIDEO_TC358746
> > > + tristate "Toshiba TC358746 parallel-CSI2 bridge"
> > > + depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER
> > > + select V4L2_FWNODE
> > > + help
> > > + Support for the Toshiba TC358746 PARALLEL to MIPI CSI-2 bridge.
> > > + The bridge can work in both directions but currenty only the
> >
> > "currently"
>
> Fixed, thanks.
>
> > > + parallel-in / csi-out path is supported.
> > > +
> > > + To compile this driver as a module, choose M here: the
> > > + module will be called tc358746.
> > > +
> > > config VIDEO_TVP514X
> > > tristate "Texas Instruments TVP514x video decoder"
> > > depends on VIDEO_V4L2 && I2C
> > > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> > > index d8ad9dad495d..3d5073cc26cf 100644
> > > --- a/drivers/media/i2c/Makefile
> > > +++ b/drivers/media/i2c/Makefile
> > > @@ -108,6 +108,7 @@ obj-$(CONFIG_VIDEO_I2C) += video-i2c.o
> > > obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o
> > > obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
> > > obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
> > > +obj-$(CONFIG_VIDEO_TC358746) += tc358746.o
> > > obj-$(CONFIG_VIDEO_IMX214) += imx214.o
> > > obj-$(CONFIG_VIDEO_IMX258) += imx258.o
> > > obj-$(CONFIG_VIDEO_IMX274) += imx274.o
> > > diff --git a/drivers/media/i2c/tc358746.c b/drivers/media/i2c/tc358746.c
> > > new file mode 100644
> > > index 000000000000..58612824b267
> > > --- /dev/null
> > > +++ b/drivers/media/i2c/tc358746.c
> > > @@ -0,0 +1,1807 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only
> > > +/*
> > > + * tc358746 - Parallel to CSI-2 bridge
> > > + *
> > > + * Copyright 2018 Marco Felsch <kernel@xxxxxxxxxxxxxx>
> > > + *
> > > + * References:
> > > + * REF_01:
> > > + * - TC358746AXBG/TC358748XBG/TC358748IXBG Functional Specification Rev 1.2
> > > + * REF_02:
> > > + * - TC358746(A)748XBG_Parallel-CSI2_Tv23p.xlsx, Rev Tv23
> > > + */
> > > +
> > > +#include <linux/clk.h>
> > > +#include <linux/clk-provider.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/gpio/consumer.h>
> > > +#include <linux/i2c.h>
> > > +#include <linux/interrupt.h>
> > > +#include <linux/kernel.h>
> > > +#include <linux/module.h>
> > > +#include <linux/property.h>
> > > +#include <linux/slab.h>
> > > +#include <linux/timer.h>
> > > +#include <media/v4l2-ctrls.h>
> > > +#include <media/v4l2-device.h>
> > > +#include <media/v4l2-fwnode.h>
> > > +
> > > +#include "tc358746_regs.h"
> > > +
> > > +static int debug;
> > > +module_param(debug, int, 0644);
> > > +MODULE_PARM_DESC(debug, "debug level (0-3)");
> > > +
> > > +MODULE_DESCRIPTION("Toshiba TC358746 Parallel to CSI-2 bridge driver");
> > > +MODULE_AUTHOR("Marco Felsch <kernel@xxxxxxxxxxxxxx>");
> > > +MODULE_LICENSE("GPL v2");
> >
> > These are usually placed at the end.
>
> Okay, I will move it at the end.
>
> > > +
> > > +#define I2C_MAX_XFER_SIZE (512 + 2)
> > > +#define TC358746_MAX_FIFO_SIZE 512
> > > +#define TC358746_DEF_LINK_FREQ 0
> > > +
> > > +#define TC358746_LINEINIT_MIN_US 110
> > > +#define TC358746_TWAKEUP_MIN_US 1200
> > > +#define TC358746_LPTXTIME_MIN_NS 55
> > > +#define TC358746_TCLKZERO_MIN_NS 305
> > > +#define TC358746_TCLKTRAIL_MIN_NS 65
> > > +#define TC358746_TCLKPOST_MIN_NS 65
> > > +#define TC358746_THSZERO_MIN_NS 150
> > > +#define TC358746_THSTRAIL_MIN_NS 65
> > > +#define TC358746_THSPREPARE_MIN_NS 45
> > > +
> > > +static const struct v4l2_mbus_framefmt tc358746_def_fmt = {
> > > + .width = 640,
> > > + .height = 480,
> > > + .code = MEDIA_BUS_FMT_UYVY8_2X8,
> > > + .field = V4L2_FIELD_NONE,
> > > + .colorspace = V4L2_COLORSPACE_DEFAULT,
> > > + .ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT,
> > > + .quantization = V4L2_QUANTIZATION_DEFAULT,
> > > + .xfer_func = V4L2_XFER_FUNC_DEFAULT,
> > > +};
> > > +
> > > +struct tc358746_csi_param {
> > > + unsigned char speed_range;
> > > + unsigned int unit_clk_hz;
> > > + unsigned char unit_clk_mul;
> > > + unsigned int speed_per_lane; /* bps / lane */
> > > + unsigned short lane_num;
> > > + bool is_continuous_clk;
> > > +
> > > + /* CSI2-TX Parameters */
> > > + u32 lineinitcnt;
> > > + u32 lptxtimecnt;
> > > + u32 twakeupcnt;
> > > + u32 tclk_preparecnt;
> > > + u32 tclk_zerocnt;
> > > + u32 tclk_trailcnt;
> > > + u32 tclk_postcnt;
> > > + u32 ths_preparecnt;
> > > + u32 ths_zerocnt;
> > > + u32 ths_trailcnt;
> > > +
> > > + unsigned int csi_hs_lp_hs_ps;
> > > +};
> >
> > Would it be possible to use struct phy_configure_opts_mipi_dphy and perhaps
> > phy_mipi_dphy_get_default_config() as well? The result of the latter will
> > surely be different though, but still expected to be valid.
>
> I've checked the struct phy_configure_opts_mipi_dphy and have a few
> points to think about:
> 1) The values I need here are counter values. The struct you mentioned
> uses time based values. This is good but needs a retranslation into
> the count values.
> 2) The tclk_zerocnt and tclk_zerocnt has a other meaning here:
> tclk_zerocnt = ckl_prepare + clk_zero > 300ns
> ths_zerocnt = hs_prepare + hs_zero > 145ns + 10 * ui
>
> I can use the struct phy_configure_opts_mipi_dphy but then the
> meaning are not the same..
>
> If I should use the phy_mipi_dphy_get_default_config() helper I had to
> reconstruct the whole logic. Currently the driver is based on the
> following behaviour:
> - the fw (DT in our case) defines possible link frequencies and data
> lane numbers
> - based on that information I calculate possible counter values to
> confirm the mipi-spec
> - now the user specifies a format and I try to serve the request by
> - adjusting the fifo-size
> if not possible
> - use other link frequency setting and retry adjusting fifo_size
> if till not possible
> - begin to reduce the resultion
>
> Imagine it that way: I configure the dphy side and adjust the parallel
> side.
>
> Now phy_mipi_dphy_get_default_config() uses the format bpp and the
> pixel_clk to calculate the exact default config. Those configs must be
> converted to the counter values. This wouldn't be a big deal but the
> excel-sheet I used to calculate the timings adds some "random"
> undocumented constants. So it would not be just a conversion from a
> time-val to a counter-val. After that we need to verify the
> parallel-input settings against the dphy-settings and do proper
> fifo/picture-soze adjustments.
>
> I would keep my approach beacause of the "random" undocumented constants
> and the other meaning of the struct phy_configure_opts_mipi_dphy
> members. Maybe I can convert it later if I have more time to verify that
> the "random" undocumented constants aren't important and can be dropped.
> Also I checked a few other Toshiba TC convert chips and it seems that
> all off them uses the same DPHY. So maybe we should split out the
> phy-part to share it.
>
> > > +
> > > +enum tc358746_csi_direction {
> > > + TC358746_CSI_RX, /* CSI-in -> Parallel-out */
> > > + TC358746_CSI_TX /* Parallel-in -> CSI-out */
> > > +};
> > > +
> > > +struct tc358746_state {
> > > + struct v4l2_subdev sd;
> > > + struct i2c_client *i2c_client;
> > > + struct gpio_desc *reset_gpio;
> > > +
> > > + /*
> > > + * Generic
> > > + */
> > > + struct media_pad pads[2];
> > > + struct mutex confctl_mutex;
> > > + struct v4l2_mbus_framefmt fmt;
> > > + struct v4l2_ctrl_handler hdl;
> > > + bool fmt_changed;
> > > + bool test;
> > > +
> > > + /*
> > > + * Chip Clocks
> > > + */
> > > + struct clk *refclk;
> > > + /* internal pll */
> > > + unsigned int pllinclk_hz;
> > > + u16 pll_prd;
> > > + u16 pll_fbd;
> > > +
> > > + /*
> > > + * Video Buffer
> > > + */
> > > + u16 vb_fifo; /* The FIFO size is 511x32 */
> > > +
> > > + /* currently only TC358746_CSI_TX supported */
> > > + enum tc358746_csi_direction csi_dir;
> > > +
> > > + /*
> > > + * CSI TX
> > > + */
> > > + struct v4l2_ctrl *link_freq;
> > > + struct tc358746_csi_param *link_freq_settings;
> > > + u64 *link_frequencies;
> > > + unsigned int link_frequencies_num;
> > > +
> > > + /*
> > > + * Parallel input
> > > + */
> > > + struct v4l2_ctrl *sensor_pclk_ctrl;
> > > + struct v4l2_ctrl *sensor_hblank_ctrl;
> > > + unsigned int pclk;
> > > + unsigned int hblank;
> > > +};
> > > +
> > > +struct tc358746_mbus_fmt {
> > > + u32 code;
> > > + u8 bus_width;
> > > + u8 bpp; /* total bpp */
> > > + u8 pdformat; /* peripheral data format */
> > > + u8 pdataf; /* parallel data format option */
> > > + u8 ppp; /* pclk per pixel */
> > > + bool csitx_only; /* format only in csi-tx mode supported */
> > > +};
> > > +
> > > +/* TODO: Add other formats as required */
> > > +static const struct tc358746_mbus_fmt tc358746_formats[] = {
> > > + {
> > > + .code = MEDIA_BUS_FMT_UYVY8_2X8,
> >
> > Note that on CSI-2 V4L2 uses the one pixel / sample variants. I.e. this
> > would be MEDIA_BUS_FMT_UYVY8_1X16.
>
> Sorry but I didn't get you. The format you mentioned is...
>
> > > + .bus_width = 8,
> > > + .bpp = 16,
> > > + .pdformat = DATAFMT_PDFMT_YCBCRFMT_422_8_BIT,
> > > + .pdataf = CONFCTL_PDATAF_MODE0,
> > > + .ppp = 2,
> > > + }, {
> > > + .code = MEDIA_BUS_FMT_UYVY8_1X16,
>
> here.
>
> > > + .bus_width = 16,
> > > + .bpp = 16,
> > > + .pdformat = DATAFMT_PDFMT_YCBCRFMT_422_8_BIT,
> > > + .pdataf = CONFCTL_PDATAF_MODE1,
> > > + .ppp = 1,
> > > + }, {
> > > + .code = MEDIA_BUS_FMT_YUYV8_1X16,
> > > + .bus_width = 16,
> > > + .bpp = 16,
> > > + .pdformat = DATAFMT_PDFMT_YCBCRFMT_422_8_BIT,
> > > + .pdataf = CONFCTL_PDATAF_MODE2,
> > > + .ppp = 1,
> > > + }, {
> > > + .code = MEDIA_BUS_FMT_UYVY10_2X10,
> > > + .bus_width = 10,
> > > + .bpp = 20,
> > > + .pdformat = DATAFMT_PDFMT_YCBCRFMT_422_10_BIT,
> > > + .pdataf = CONFCTL_PDATAF_MODE0, /* don't care */
> > > + .ppp = 2,
> > > + }, {
> > > + /* in datasheet listed as YUV444 */
> > > + .code = MEDIA_BUS_FMT_GBR888_1X24,
> > > + .bus_width = 24,
> > > + .bpp = 24,
> > > + .pdformat = DATAFMT_PDFMT_YCBCRFMT_444,
> > > + .pdataf = CONFCTL_PDATAF_MODE0, /* don't care */
> > > + .ppp = 2,
> > > + .csitx_only = true,
> > > + },
> > > +};
> > > +
> > > +/* --------------- HELPERS ------------ */
> > > +static void
> > > +tc358746_dump_csi(struct v4l2_subdev *sd,
> > > + struct tc358746_csi_param *csi_setting)
> > > +{
> > > + v4l2_dbg(2, debug, sd, "Speed-Range value %u\n",
> > > + csi_setting->speed_range);
> > > + v4l2_dbg(2, debug, sd, "Unit Clock %u Hz\n", csi_setting->unit_clk_hz);
> > > + v4l2_dbg(2, debug, sd, "Unit Clock Mul %u\n",
> > > + csi_setting->unit_clk_mul);
> > > + v4l2_dbg(2, debug, sd, "CSI speed/lane %u bps/lane\n",
> > > + csi_setting->speed_per_lane);
> > > + v4l2_dbg(2, debug, sd, "CSI lanes %u\n", csi_setting->lane_num);
> > > + v4l2_dbg(2, debug, sd, "CSI clock during LP %sabled\n",
> > > + csi_setting->is_continuous_clk ? "en" : "dis");
> > > +
> > > + v4l2_dbg(2, debug, sd, "lineinitcnt %u\n", csi_setting->lineinitcnt);
> > > + v4l2_dbg(2, debug, sd, "lptxtimecnt %u\n", csi_setting->lptxtimecnt);
> > > + v4l2_dbg(2, debug, sd, "tclk_preparecnt %u\n",
> > > + csi_setting->tclk_preparecnt);
> > > + v4l2_dbg(2, debug, sd, "tclk_zerocnt %u\n", csi_setting->tclk_zerocnt);
> > > + v4l2_dbg(2, debug, sd, "tclk_trailcnt %u\n",
> > > + csi_setting->tclk_trailcnt);
> > > + v4l2_dbg(2, debug, sd, "ths_preparecnt %u\n",
> > > + csi_setting->ths_preparecnt);
> > > + v4l2_dbg(2, debug, sd, "ths_zerocnt %u\n", csi_setting->ths_zerocnt);
> > > + v4l2_dbg(2, debug, sd, "twakeupcnt %u\n", csi_setting->twakeupcnt);
> > > + v4l2_dbg(2, debug, sd, "tclk_postcnt %u\n", csi_setting->tclk_postcnt);
> > > + v4l2_dbg(2, debug, sd, "ths_trailcnt %u\n", csi_setting->ths_trailcnt);
> > > + v4l2_dbg(2, debug, sd, "csi_hs_lp_hs_ps %u (%u us)\n",
> > > + csi_setting->csi_hs_lp_hs_ps,
> > > + csi_setting->csi_hs_lp_hs_ps / 1000);
> > > +}
> > > +
> > > +static void
> > > +tc358746_dump_pll(struct v4l2_subdev *sd, struct tc358746_state *state)
> > > +{
> > > + v4l2_dbg(2, debug, sd, "refclk %lu Hz\n", clk_get_rate(state->refclk));
> > > + v4l2_dbg(2, debug, sd, "pll input clock %u Hz\n", state->pllinclk_hz);
> > > + v4l2_dbg(2, debug, sd, "PLL_PRD %u\n", state->pll_prd - 1);
> > > + v4l2_dbg(2, debug, sd, "PLL_FBD %u\n", state->pll_fbd - 1);
> > > +}
> > > +
> > > +static inline struct tc358746_state *to_state(struct v4l2_subdev *sd)
> > > +{
> > > + return container_of(sd, struct tc358746_state, sd);
> > > +}
> > > +
> > > +/* Find a data format by a pixel code */
> > > +static int tc358746_format_supported(u32 code)
> > > +{
> > > + unsigned int i;
> > > +
> > > + for (i = 0; i < ARRAY_SIZE(tc358746_formats); i++)
> > > + if (tc358746_formats[i].code == code)
> > > + return 0;
> > > +
> > > + return -EINVAL;
> > > +}
> > > +
> > > +static struct tc358746_csi_param *
> > > +tc358746_g_cur_csi_settings(struct tc358746_state *state)
> > > +{
> > > + unsigned int cur_freq = v4l2_ctrl_g_ctrl(state->link_freq);
> > > +
> > > + return &state->link_freq_settings[cur_freq];
> > > +}
> > > +
> > > +static const struct tc358746_mbus_fmt *tc358746_get_format(u32 code)
> > > +{
> > > + unsigned int i;
> > > +
> > > + for (i = 0; i < ARRAY_SIZE(tc358746_formats); i++)
> > > + if (tc358746_formats[i].code == code)
> > > + return &tc358746_formats[i];
> > > +
> > > + return NULL;
> > > +}
> > > +
> > > +static int
> > > +tc358746_adjust_fifo_size(struct tc358746_state *state,
> > > + const struct tc358746_mbus_fmt *format,
> > > + struct tc358746_csi_param *csi_settings,
> > > + unsigned int width, u16 *fifo_size)
> > > +{
> > > + int c_hactive_ps_diff, c_lp_active_ps_diff, c_fifo_delay_ps_diff;
> > > + unsigned int p_hactive_ps, p_hblank_ps, p_htotal_ps;
> > > + unsigned int c_hactive_ps, c_lp_active_ps, c_fifo_delay_ps;
> > > + unsigned int csi_bps, csi_bps_period_ps;
> > > + unsigned int csi_hsclk, csi_hsclk_period_ps;
> > > + unsigned int pclk_period_ps;
> > > + unsigned int _fifo_size;
> > > +
> > > + pclk_period_ps = 1000000000 / (state->pclk / 1000);
> > > + csi_bps = csi_settings->speed_per_lane * csi_settings->lane_num;
> > > + csi_bps_period_ps = 1000000000 / (csi_bps / 1000);
> > > + csi_hsclk = csi_settings->speed_per_lane >> 3;
> > > + csi_hsclk_period_ps = 1000000000 / (csi_hsclk / 1000);
> > > +
> > > + /*
> > > + * Calculation:
> > > + * p_hactive_ps = pclk_period_ps * pclk_per_pixel * h_active_pixel
> > > + */
> > > + p_hactive_ps = pclk_period_ps * format->ppp * width;
> > > +
> > > + /*
> > > + * Calculation:
> > > + * p_hblank_ps = pclk_period_ps * h_blank_pixel
> > > + */
> > > + p_hblank_ps = pclk_period_ps * state->hblank;
> > > + p_htotal_ps = p_hblank_ps + p_hactive_ps;
> > > +
> > > + /*
> > > + * Adjust the fifo size to adjust the csi timing. Hopefully we can find
> > > + * a fifo size where the parallel input timings and the csi tx timings
> > > + * fit together.
> > > + */
> > > + for (_fifo_size = 1; _fifo_size < TC358746_MAX_FIFO_SIZE;
> > > + _fifo_size++) {
> > > + /*
> > > + * Calculation:
> > > + * c_fifo_delay_ps = (fifo_size * 32) / parallel_bus_width *
> > > + * pclk_period_ps + 4 * csi_hsclk_period_ps
> > > + */
> > > + c_fifo_delay_ps = _fifo_size * 32 * pclk_period_ps;
> > > + c_fifo_delay_ps /= format->bus_width;
> > > + c_fifo_delay_ps += 4 * csi_hsclk_period_ps;
> > > +
> > > + /*
> > > + * Calculation:
> > > + * c_hactive_ps = csi_bps_period_ps * image_bpp * h_active_pixel
> > > + * + c_fifo_delay
> > > + */
> > > + c_hactive_ps = csi_bps_period_ps * format->bpp * width;
> > > + c_hactive_ps += c_fifo_delay_ps;
> > > +
> > > + /*
> > > + * Calculation:
> > > + * c_lp_active_ps = p_htotal_ps - c_hactive_ps
> > > + */
> > > + c_lp_active_ps = p_htotal_ps - c_hactive_ps;
> > > +
> > > + c_hactive_ps_diff = c_hactive_ps - p_hactive_ps;
> > > + c_fifo_delay_ps_diff = p_htotal_ps - c_hactive_ps;
> > > + c_lp_active_ps_diff =
> > > + c_lp_active_ps - csi_settings->csi_hs_lp_hs_ps;
> > > +
> > > + if (c_hactive_ps_diff > 0 &&
> > > + c_fifo_delay_ps_diff > 0 &&
> > > + c_lp_active_ps_diff > 0)
> > > + break;
> > > + }
> > > +
> > > + /*
> > > + * If we can't transfer the image using this csi link frequency try to
> > > + * use another link freq.
> > > + */
> > > + v4l2_dbg(1, debug, &state->sd, "found fifo-size %d\n",
> > > + _fifo_size == TC358746_MAX_FIFO_SIZE ? -1 : _fifo_size);
> > > + *fifo_size = _fifo_size;
> > > + return _fifo_size == TC358746_MAX_FIFO_SIZE ? -EINVAL : 0;
> > > +}
> > > +
> > > +static int
> > > +tc358746_adjust_timings(struct tc358746_state *state,
> > > + const struct tc358746_mbus_fmt *format,
> > > + unsigned int *width, u16 *fifo_size)
> > > +{
> > > +
> > > + unsigned int cur_freq = v4l2_ctrl_g_ctrl(state->link_freq);
> > > + unsigned int freq = cur_freq;
> > > + struct tc358746_csi_param *csi_lane_setting;
> > > + int err;
> > > + int _width;
> > > +
> > > + /*
> > > + * Adjust timing:
> > > + * 1) Try to use the desired width and the current csi-link-frequency
> > > + * 2) If this doesn't fit try other csi-link-frequencies
> > > + * 3) If this doesn't fit too, reducing the desired width and test
> > > + * it again width the current csi-link-frequency
> > > + * 4) Goto step 2 if it doesn't fit at all
> > > + */
> > > + for (_width = *width; _width > 0; _width -= 10) {
> > > + csi_lane_setting = &state->link_freq_settings[cur_freq];
> > > + err = tc358746_adjust_fifo_size(state, format, csi_lane_setting,
> > > + _width, fifo_size);
> > > + if (!err)
> > > + goto out;
> > > +
> > > + for (freq = 0; freq < state->link_frequencies_num; freq++) {
> > > + if (freq == cur_freq)
> > > + continue;
> > > +
> > > + csi_lane_setting = &state->link_freq_settings[freq];
> > > + err = tc358746_adjust_fifo_size(state, format,
> > > + csi_lane_setting,
> > > + _width, fifo_size);
> > > + if (!err)
> > > + goto out;
> > > + }
> > > + }
> > > +
> > > +out:
> > > + *width = _width;
> > > + return freq;
> > > +}
> > > +
> > > +static int
> > > +tc358746_calculate_csi_txtimings(struct tc358746_state *state,
> > > + struct tc358746_csi_param *csi_setting)
> > > +{
> > > + unsigned int spl;
> > > + unsigned int spl_p_ps, hsclk_p_ps, hfclk_p_ns;
> > > + unsigned int hfclk, hsclk; /* SYSCLK */
> > > + unsigned int tmp;
> > > + unsigned int lptxtime_ps, tclk_post_ps, tclk_trail_ps, tclk_zero_ps,
> > > + ths_trail_ps, ths_zero_ps;
> > > +
> > > + spl = csi_setting->speed_per_lane;
> > > + hsclk = spl >> 3; /* spl in bit-per-second, hsclk in byte-per-sercond */
> > > + hfclk = hsclk >> 1; /* HFCLK = SYSCLK / 2 */
> > > +
> > > + if (hsclk > 125000000U) {
> > > + v4l2_err(&state->sd, "unsupported HS byte clock %d, must <= 125 MHz\n",
> > > + hsclk);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + hfclk_p_ns = DIV_ROUND_CLOSEST(1000000000, hfclk);
> > > + hsclk_p_ps = 1000000000 / (hsclk / 1000);
> > > + spl_p_ps = 1000000000 / (spl / 1000);
> > > +
> > > + /*
> > > + * Calculation:
> > > + * hfclk_p_ns * lineinitcnt > 100us
> > > + * lineinitcnt > 100 * 10^-6s / hfclk_p_ns * 10^-9
> > > + *
> > > + */
> > > + csi_setting->lineinitcnt = DIV_ROUND_UP(TC358746_LINEINIT_MIN_US * 1000,
> > > + hfclk_p_ns);
> > > +
> > > + /*
> > > + * Calculation:
> > > + * (lptxtimecnt + 1) * hsclk_p_ps > 50ns
> > > + * 38ns < (tclk_preparecnt + 1) * hsclk_p_ps < 95ns
> > > + */
> > > + csi_setting->lptxtimecnt = csi_setting->tclk_preparecnt =
> > > + DIV_ROUND_UP(TC358746_LPTXTIME_MIN_NS * 1000, hsclk_p_ps) - 1;
> > > +
> > > + /*
> > > + * Limit:
> > > + * (tclk_zero + tclk_prepar) period > 300ns.
> > > + * Since we have no upper limit and for simplicity:
> > > + * tclk_zero > 300ns.
> > > + *
> > > + * Calculation:
> > > + * tclk_zero = ([2,3] + tclk_zerocnt) * hsclk_p_ps + ([2,3] * spl_p_ps)
> > > + *
> > > + * Note: REF_02 uses
> > > + * tclk_zero = (2.5 + tclk_zerocnt) * hsclk_p_ps + (3.5 * spl_p_ps)
> > > + */
> > > + tmp = TC358746_TCLKZERO_MIN_NS * 1000 - 3 * spl_p_ps;
> > > + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> > > + csi_setting->tclk_zerocnt = tmp - 2;
> > > +
> > > + /*
> > > + * Limit:
> > > + * 40ns + 4 * spl_p_ps < (ths_preparecnt + 1) * hsclk_p_ps
> > > + * < 85ns + 6 * spl_p_ps
> > > + */
> > > + tmp = TC358746_THSPREPARE_MIN_NS * 1000 + 4 * spl_p_ps;
> > > + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> > > + csi_setting->ths_preparecnt = tmp - 1;
> > > +
> > > + /*
> > > + * Limit:
> > > + * (ths_zero + ths_prepare) period > 145ns + 10 * spl_p_ps.
> > > + * Since we have no upper limit and for simplicity:
> > > + * ths_zero period > 145ns + 10 * spl_p_ps.
> > > + *
> > > + * Calculation:
> > > + * ths_zero = ([6,8] + ths_zerocnt) * hsclk_p_ps + [3,4] * hsclk_p_ps +
> > > + * [13,14] * spl_p_ps
> > > + *
> > > + * Note: REF_02 uses
> > > + * ths_zero = (7 + ths_zerocnt) * hsclk_p_ps + 4 * hsclk_p_ps +
> > > + * 11 * spl_p_ps
> > > + */
> > > + tmp = TC358746_THSZERO_MIN_NS * 1000 - spl_p_ps;
> > > + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> > > + csi_setting->ths_zerocnt = tmp < 11 ? 0 : tmp - 11;
> > > +
> > > + /*
> > > + * Limit:
> > > + * hsclk_p_ps * (lptxtimecnt + 1) * (twakeupcnt + 1) > 1ms
> > > + *
> > > + * Since we have no upper limit use 1.2ms as lower limit to
> > > + * surley meet the spec limit.
> > > + */
> > > + tmp = hsclk_p_ps / 1000; /* tmp = hsclk_p_ns */
> > > + csi_setting->twakeupcnt =
> > > + DIV_ROUND_UP(TC358746_TWAKEUP_MIN_US * 1000,
> > > + tmp * (csi_setting->lptxtimecnt + 1)) - 1;
> > > +
> > > + /*
> > > + * Limit:
> > > + * 60ns + 4 * spl_p_ps < thstrail < 105ns + 12 * spl_p_ps
> > > + *
> > > + * Calculation:
> > > + * thstrail = (1 + ths_trailcnt) * hsclk_p_ps + [3,4] * hsclk_p_ps -
> > > + * [13,14] * spl_p_ps
> > > + *
> > > + * [2] set formula to:
> > > + * thstrail = (1 + ths_trailcnt) * hsclk_p_ps + 4 * hsclk_p_ps -
> > > + * 11 * spl_p_ps
> > > + */
> > > + tmp = TC358746_THSTRAIL_MIN_NS * 1000 + 15 * spl_p_ps;
> > > + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> > > + csi_setting->ths_trailcnt = tmp - 5;
> > > +
> > > + /*
> > > + * Limit:
> > > + * 60ns < tclk_trail < 105ns + 12 * spl_p_ps
> > > + *
> > > + * Limit used by REF_02:
> > > + * 60ns < tclk_trail < 105ns + 12 * spl_p_ps - 30
> > > + *
> > > + * Calculation:
> > > + * tclk_trail = ([1,2] + tclk_trailcnt) * hsclk_p_ps +
> > > + * (2 + [1,2]) * hsclk_p_ps - [2,3] * spl_p_ps
> > > + *
> > > + * Calculation used by REF_02:
> > > + * tclk_trail = (1 + tclk_trailcnt) * hsclk_p_ps +
> > > + * 4 * hsclk_p_ps - 3 * spl_p_ps
> > > + */
> > > + tmp = TC358746_TCLKTRAIL_MIN_NS * 1000 + 3 * spl_p_ps;
> > > + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> > > + csi_setting->tclk_trailcnt = tmp < 5 ? 0 : tmp - 5;
> > > +
> > > + /*
> > > + * Limit:
> > > + * tclk_post > 60ns + 52 * spl_p_ps
> > > + *
> > > + * Limit used by REF_02:
> > > + * tclk_post > 60ns + 52 * spl_p_ps
> > > + *
> > > + * Calculation:
> > > + * tclk_post = ([1,2] + (tclk_postcnt + 1)) * hsclk_p_ps + hsclk_p_ps
> > > + *
> > > + * Note REF_02 uses:
> > > + * tclk_post = (2.5 + tclk_postcnt) * hsclk_p_ps + hsclk_p_ps +
> > > + * 2.5 * spl_p_ps
> > > + * To meet the REF_02 validation limits following equation is used:
> > > + * tclk_post = (2 + tclk_postcnt) * hsclk_p_ps + hsclk_p_ps +
> > > + * 3 * spl_p_ps
> > > + */
> > > + tmp = TC358746_TCLKPOST_MIN_NS * 1000 + 49 * spl_p_ps;
> > > + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> > > + csi_setting->tclk_postcnt = tmp - 3;
> > > +
> > > + /*
> > > + * Last calculate the csi hs->lp->hs transistion time in ns. Note REF_02
> > > + * mixed units in the equation for the continuous case. I don't know if
> > > + * this was the intention. The driver drops the last 'multiply all by
> > > + * two' to get nearly the same results.
> > > + */
> > > + lptxtime_ps = (csi_setting->lptxtimecnt + 1) * hsclk_p_ps;
> > > + tclk_post_ps =
> > > + (4 + csi_setting->tclk_postcnt) * hsclk_p_ps + 3 * spl_p_ps;
> > > + tclk_trail_ps =
> > > + (5 + csi_setting->tclk_trailcnt) * hsclk_p_ps - 3 * spl_p_ps;
> > > + tclk_zero_ps =
> > > + (2 + csi_setting->tclk_zerocnt) * hsclk_p_ps + 3 * spl_p_ps;
> > > + ths_trail_ps =
> > > + (5 + csi_setting->ths_trailcnt) * hsclk_p_ps - 11 * spl_p_ps;
> > > + ths_zero_ps =
> > > + (7 + csi_setting->ths_zerocnt) * hsclk_p_ps + 4 * hsclk_p_ps +
> > > + 11 * spl_p_ps;
> > > +
> > > + if (csi_setting->is_continuous_clk) {
> > > + tmp = 2 * lptxtime_ps;
> > > + tmp += 25 * hsclk_p_ps;
> > > + tmp += ths_trail_ps;
> > > + tmp += ths_zero_ps;
> > > + } else {
> > > + tmp = 4 * lptxtime_ps;
> > > + tmp += ths_trail_ps + tclk_post_ps + tclk_trail_ps +
> > > + tclk_zero_ps + ths_zero_ps;
> > > + tmp += (13 + csi_setting->lptxtimecnt * 8) * hsclk_p_ps;
> > > + tmp += 22 * hsclk_p_ps;
> > > + tmp *= 3;
> > > + tmp = DIV_ROUND_CLOSEST(tmp, 2);
> > > + }
> > > + csi_setting->csi_hs_lp_hs_ps = tmp;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +/* --------------- i2c helper ------------ */
> > > +
> > > +static void i2c_rd(struct v4l2_subdev *sd, u16 reg, u8 *values, u32 n)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + struct i2c_client *client = state->i2c_client;
> > > + int err;
> > > + u8 buf[2] = { reg >> 8, reg & 0xff };
> > > + u8 data[I2C_MAX_XFER_SIZE];
> > > +
> > > + struct i2c_msg msgs[] = {
> > > + {
> > > + .addr = client->addr,
> > > + .flags = 0,
> > > + .len = 2,
> > > + .buf = buf,
> > > + },
> > > + {
> > > + .addr = client->addr,
> > > + .flags = I2C_M_RD,
> > > + .len = n,
> > > + .buf = data,
> > > + },
> > > + };
> > > +
> > > + err = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
> > > + if (err != ARRAY_SIZE(msgs)) {
> > > + v4l2_err(sd, "%s: reading register 0x%x from 0x%x failed\n",
> > > + __func__, reg, client->addr);
> > > + }
> > > +
> > > + switch (n) {
> > > + case 1:
> > > + values[0] = data[0];
> > > + break;
> > > + case 2:
> > > + values[0] = data[1];
> > > + values[1] = data[0];
> > > + break;
> > > + case 4:
> > > + values[0] = data[1];
> > > + values[1] = data[0];
> > > + values[2] = data[3];
> > > + values[3] = data[2];
> > > + break;
> > > + default:
> > > + v4l2_info(sd, "unsupported I2C read %d bytes from address 0x%04x\n",
> > > + n, reg);
> > > + }
> > > +
> > > + if (debug < 3)
> > > + return;
> > > +
> > > + switch (n) {
> > > + case 1:
> > > + v4l2_info(sd, "I2C read 0x%04x = 0x%02x",
> > > + reg, data[0]);
> > > + break;
> > > + case 2:
> > > + v4l2_info(sd, "I2C read 0x%04x = 0x%02x%02x",
> > > + reg, data[0], data[1]);
> > > + break;
> > > + case 4:
> > > + v4l2_info(sd, "I2C read 0x%04x = 0x%02x%02x%02x%02x",
> > > + reg, data[2], data[3], data[0], data[1]);
> > > + break;
> > > + default:
> > > + v4l2_info(sd, "I2C unsupported read %d bytes from address 0x%04x\n",
> > > + n, reg);
> > > + }
> > > +}
> > > +
> > > +static void i2c_wr(struct v4l2_subdev *sd, u16 reg, u8 *values, u32 n)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + struct i2c_client *client = state->i2c_client;
> > > + int err;
> > > + struct i2c_msg msg;
> > > + u8 data[I2C_MAX_XFER_SIZE];
> > > +
> > > + if ((2 + n) > I2C_MAX_XFER_SIZE) {
> > > + n = I2C_MAX_XFER_SIZE - 2;
> > > + v4l2_warn(sd, "i2c wr reg=%04x: len=%d is too big!\n",
> > > + reg, 2 + n);
> > > + }
> > > +
> > > + msg.addr = client->addr;
> > > + msg.buf = data;
> > > + msg.len = 2 + n;
> > > + msg.flags = 0;
> > > +
> > > + data[0] = reg >> 8;
> > > + data[1] = reg & 0xff;
> > > +
> > > + switch (n) {
> > > + case 1:
> > > + data[2 + 0] = values[0];
> > > + break;
> > > + case 2:
> > > + data[2 + 0] = values[1];
> > > + data[2 + 1] = values[0];
> > > + break;
> > > + case 4:
> > > + data[2 + 0] = values[1];
> > > + data[2 + 1] = values[0];
> > > + data[2 + 2] = values[3];
> > > + data[2 + 3] = values[2];
> > > + break;
> > > + default:
> > > + v4l2_info(sd, "unsupported I2C write %d bytes from address 0x%04x\n",
> > > + n, reg);
> >
> > You'd need to return here. Perhaps WARN_ON(1) instead of v4l2_info(), as
> > this would presumably be a driver bug.
>
> Okay.
>
> > > + }
> > > +
> > > + err = i2c_transfer(client->adapter, &msg, 1);
> > > + if (err != 1) {
> > > + v4l2_err(sd, "%s: writing register 0x%x from 0x%x failed\n",
> > > + __func__, reg, client->addr);
> > > + return;
> > > + }
> > > +
> > > + if (debug < 3)
> > > + return;
> > > +
> > > + switch (n) {
> > > + case 1:
> > > + v4l2_info(sd, "I2C write 0x%04x = 0x%02x", reg, data[2 + 0]);
> > > + break;
> > > + case 2:
> > > + v4l2_info(sd, "I2C write 0x%04x = 0x%02x%02x", reg, data[2 + 0],
> > > + data[2 + 1]);
> > > + break;
> > > + case 4:
> > > + v4l2_info(sd, "I2C write 0x%04x = 0x%02x%02x%02x%02x", reg,
> > > + data[2 + 2], data[2 + 3], data[2 + 0], data[2 + 1]);
> > > + break;
> > > + default:
> > > + v4l2_info(sd, "I2C unsupported write %d bytes from address 0x%04x\n",
> > > + n, reg);
> > > + }
> > > +}
> > > +
> > > +static noinline u32 i2c_rdreg(struct v4l2_subdev *sd, u16 reg, u32 n)
> > > +{
> > > + __le32 val = 0;
> > > +
> > > + i2c_rd(sd, reg, (u8 __force *)&val, n);
> > > +
> > > + return le32_to_cpu(val);
> > > +}
> > > +
> > > +static noinline void i2c_wrreg(struct v4l2_subdev *sd, u16 reg, u32 val, u32 n)
> > > +{
> > > + __le32 raw = cpu_to_le32(val);
> > > +
> > > + i2c_wr(sd, reg, (u8 __force *)&raw, n);
> > > +}
> > > +
> > > +static u16 __maybe_unused i2c_rd8(struct v4l2_subdev *sd, u16 reg)
> > > +{
> > > + return i2c_rdreg(sd, reg, 1);
> > > +}
> > > +
> > > +static u16 __maybe_unused i2c_rd16(struct v4l2_subdev *sd, u16 reg)
> > > +{
> > > + return i2c_rdreg(sd, reg, 2);
> > > +}
> > > +
> > > +static u32 __maybe_unused i2c_rd32(struct v4l2_subdev *sd, u16 reg)
> > > +{
> > > + return i2c_rdreg(sd, reg, 4);
> > > +}
> > > +
> > > +static void __maybe_unused i2c_wr8(struct v4l2_subdev *sd, u16 reg, u16 val)
> > > +{
> > > + i2c_wrreg(sd, reg, val, 1);
> > > +}
> > > +
> > > +static void i2c_wr16(struct v4l2_subdev *sd, u16 reg, u16 val)
> > > +{
> > > + i2c_wrreg(sd, reg, val, 2);
> > > +}
> > > +
> > > +static void i2c_wr16_and_or(struct v4l2_subdev *sd, u16 reg, u32 mask, u16 val)
> > > +{
> > > + u16 m = (u16) ~mask;
> > > +
> > > + i2c_wrreg(sd, reg, (i2c_rd16(sd, reg) & m) | val, 2);
> > > +}
> > > +
> > > +static void i2c_wr32(struct v4l2_subdev *sd, u16 reg, u32 val)
> > > +{
> > > + i2c_wrreg(sd, reg, val, 4);
> > > +}
> > > +
> > > +/* --------------- init --------------- */
> > > +
> > > +static void
> > > +tc358746_wr_csi_control(struct v4l2_subdev *sd, int val)
> > > +{
> > > + u32 _val;
> > > +
> > > + val &= CSI_CONFW_DATA_MASK;
> > > + _val = CSI_CONFW_MODE_SET_MASK | CSI_CONFW_ADDRESS_CSI_CONTROL_MASK |
> > > + val;
> > > +
> > > + v4l2_dbg(2, debug, sd, "CSI_CONFW 0x%04x\n", _val);
> > > + i2c_wr32(sd, CSI_CONFW, _val);
> > > +}
> > > +
> > > +static inline void tc358746_sleep_mode(struct v4l2_subdev *sd, int enable)
> > > +{
> > > + i2c_wr16_and_or(sd, SYSCTL, SYSCTL_SLEEP_MASK,
> > > + enable ? SYSCTL_SLEEP_MASK : 0);
> > > +}
> > > +
> > > +static inline void tc358746_sreset(struct v4l2_subdev *sd)
> > > +{
> > > + i2c_wr16(sd, SYSCTL, SYSCTL_SRESET_MASK);
> > > + udelay(10);
> > > + i2c_wr16(sd, SYSCTL, 0);
> > > +}
> > > +
> > > +static inline void tc358746_enable_stream(struct v4l2_subdev *sd, int enable)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > +
> > > + v4l2_dbg(1, debug, sd, "%sable\n", enable ? "en" : "dis");
> > > +
> > > + mutex_lock(&state->confctl_mutex);
> > > + if (!enable) {
> > > + i2c_wr16_and_or(sd, PP_MISC, PP_MISC_FRMSTOP_MASK,
> > > + PP_MISC_FRMSTOP_MASK);
> > > + i2c_wr16_and_or(sd, CONFCTL, CONFCTL_PPEN_MASK, 0);
> > > + i2c_wr16_and_or(sd, PP_MISC, PP_MISC_RSTPTR_MASK,
> > > + PP_MISC_RSTPTR_MASK);
> > > +
> > > + i2c_wr32(sd, CSIRESET, (CSIRESET_RESET_CNF_MASK |
> > > + CSIRESET_RESET_MODULE_MASK));
> > > + i2c_wr16(sd, DBG_ACT_LINE_CNT, 0);
> > > + } else {
> > > + i2c_wr16(sd, PP_MISC, 0);
> > > + i2c_wr16_and_or(sd, CONFCTL, CONFCTL_PPEN_MASK,
> > > + CONFCTL_PPEN_MASK);
> > > + }
> > > + mutex_unlock(&state->confctl_mutex);
> > > +}
> > > +
> > > +static void tc358746_set_pll(struct v4l2_subdev *sd)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + struct tc358746_csi_param *csi_setting =
> > > + tc358746_g_cur_csi_settings(state);
> > > + u16 pllctl0 = i2c_rd16(sd, PLLCTL0);
> > > + u16 pllctl1 = i2c_rd16(sd, PLLCTL1);
> > > + u16 pll_frs = csi_setting->speed_range;
> > > + u16 pllctl0_new;
> > > +
> > > + /*
> > > + * Calculation:
> > > + * speed_per_lane = (pllinclk_hz * (fbd + 1)) / 2^frs
> > > + *
> > > + * Calculation used by REF_02:
> > > + * speed_per_lane = (pllinclk_hz * fbd) / 2^frs
> > > + */
> > > + state->pll_fbd = csi_setting->speed_per_lane / state->pllinclk_hz;
> > > + state->pll_fbd <<= pll_frs;
> > > +
> > > + pllctl0_new = PLLCTL0_PLL_PRD_SET(state->pll_prd) |
> > > + PLLCTL0_PLL_FBD_SET(state->pll_fbd);
> > > +
> > > + /*
> > > + * Only rewrite when needed (new value or disabled), since rewriting
> > > + * triggers another format change event.
> > > + */
> > > + if ((pllctl0 != pllctl0_new) ||
> > > + ((pllctl1 & PLLCTL1_PLL_EN_MASK) == 0)) {
> > > + u16 pllctl1_mask = PLLCTL1_PLL_FRS_MASK | PLLCTL1_RESETB_MASK |
> > > + PLLCTL1_PLL_EN_MASK;
> > > + u16 pllctl1_val = PLLCTL1_PLL_FRS_SET(pll_frs) |
> > > + PLLCTL1_RESETB_MASK | PLLCTL1_PLL_EN_MASK;
> > > +
> > > + v4l2_dbg(1, debug, sd, "Updating PLL clock\n");
> > > + i2c_wr16(sd, PLLCTL0, pllctl0_new);
> > > + i2c_wr16_and_or(sd, PLLCTL1, pllctl1_mask, pllctl1_val);
> > > + udelay(1000);
> > > + i2c_wr16_and_or(sd, PLLCTL1, PLLCTL1_CKEN_MASK,
> > > + PLLCTL1_CKEN_MASK);
> > > + }
> > > +
> > > + tc358746_dump_pll(sd, state);
> > > +}
> > > +
> > > +static void tc358746_set_csi_color_space(struct v4l2_subdev *sd)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + const struct tc358746_mbus_fmt *tc358746_fmt =
> > > + tc358746_get_format(state->fmt.code);
> > > +
> > > + /* currently no self defined csi user data type id's are supported */
> > > + mutex_lock(&state->confctl_mutex);
> > > + i2c_wr16_and_or(sd, DATAFMT,
> > > + (DATAFMT_PDFMT_MASK | DATAFMT_UDT_EN_MASK),
> > > + DATAFMT_PDFMT_SET(tc358746_fmt->pdformat));
> > > + i2c_wr16_and_or(sd, CONFCTL, CONFCTL_PDATAF_MASK,
> > > + CONFCTL_PDATAF_SET(tc358746_fmt->pdataf));
> > > + mutex_unlock(&state->confctl_mutex);
> > > +}
> > > +
> > > +static void tc38764_debug_pattern_80(struct v4l2_subdev *sd)
> > > +{
> > > + unsigned int i;
> > > +
> > > + i2c_wr16(sd, DBG_ACT_LINE_CNT, 0x8000);
> > > + i2c_wr16(sd, DBG_LINE_WIDTH, 0x0396);
> > > + i2c_wr16(sd, DBG_VERT_BLANK_LINE_CNT, 0x0000);
> > > +
> > > + for (i = 0; i < 80; i++)
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0xff7f);
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0xff00);
> > > + for (i = 0; i < 40; i++)
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0xffff);
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0xc0ff);
> > > + for (i = 0; i < 40; i++)
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0xc000);
> > > + for (i = 0; i < 80; i++)
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0x7f00);
> > > + for (i = 0; i < 80; i++)
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0x7fff);
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0x0000);
> > > + for (i = 0; i < 40; i++)
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0x00ff);
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0x00ff);
> > > + for (i = 0; i < 40; i++)
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0x0000);
> > > + i2c_wr16(sd, DBG_VIDEO_DATA, 0x007f);
> > > +
> > > + i2c_wr16(sd, DBG_ACT_LINE_CNT, 0xC1DF);
> > > +}
> > > +
> > > +static void tc358746_enable_csi_lanes(struct v4l2_subdev *sd, int enable)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + struct tc358746_csi_param *csi_setting =
> > > + tc358746_g_cur_csi_settings(state);
> > > + unsigned int lanes = csi_setting->lane_num;
> > > + u32 val = 0;
> > > +
> > > + if (lanes < 1 || !enable)
> > > + i2c_wr32(sd, CLW_CNTRL, CLW_CNTRL_CLW_LANEDISABLE_MASK);
> > > + if (lanes < 1 || !enable)
> > > + i2c_wr32(sd, D0W_CNTRL, D0W_CNTRL_D0W_LANEDISABLE_MASK);
> >
> > Please put the two in the same basic block; no need for two conditions that
> > are the same.
> >
> > > + if (lanes < 2 || !enable)
> > > + i2c_wr32(sd, D1W_CNTRL, D1W_CNTRL_D1W_LANEDISABLE_MASK);
> > > + if (lanes < 3 || !enable)
> > > + i2c_wr32(sd, D2W_CNTRL, D2W_CNTRL_D2W_LANEDISABLE_MASK);
> > > + if (lanes < 4 || !enable)
> > > + i2c_wr32(sd, D3W_CNTRL, D2W_CNTRL_D3W_LANEDISABLE_MASK);
> > > +
> > > + if (lanes > 0 && enable)
> >
> > Isn't lanes always greater than 0?
>
> Sure.. changed this and above comment.
>
> > > + val |= HSTXVREGEN_CLM_HSTXVREGEN_MASK |
> > > + HSTXVREGEN_D0M_HSTXVREGEN_MASK;
> > > + if (lanes > 1 && enable)
> > > + val |= HSTXVREGEN_D1M_HSTXVREGEN_MASK;
> > > + if (lanes > 2 && enable)
> > > + val |= HSTXVREGEN_D2M_HSTXVREGEN_MASK;
> > > + if (lanes > 3 && enable)
> > > + val |= HSTXVREGEN_D3M_HSTXVREGEN_MASK;
> > > +
> > > + i2c_wr32(sd, HSTXVREGEN, val);
> > > +}
> > > +
> > > +static void tc358746_set_csi(struct v4l2_subdev *sd)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + struct tc358746_csi_param *csi_setting =
> > > + tc358746_g_cur_csi_settings(state);
> > > + bool en_continuous_clk = csi_setting->is_continuous_clk;
> > > + u32 val;
> > > +
> > > + val = TCLK_HEADERCNT_TCLK_ZEROCNT_SET(csi_setting->tclk_zerocnt) |
> > > + TCLK_HEADERCNT_TCLK_PREPARECNT_SET(csi_setting->tclk_preparecnt);
> > > + i2c_wr32(sd, TCLK_HEADERCNT, val);
> > > + val = THS_HEADERCNT_THS_ZEROCNT_SET(csi_setting->ths_zerocnt) |
> > > + THS_HEADERCNT_THS_PREPARECNT_SET(csi_setting->ths_preparecnt);
> > > + i2c_wr32(sd, THS_HEADERCNT, val);
> > > + i2c_wr32(sd, TWAKEUP, csi_setting->twakeupcnt);
> > > + i2c_wr32(sd, TCLK_POSTCNT, csi_setting->tclk_postcnt);
> > > + i2c_wr32(sd, THS_TRAILCNT, csi_setting->ths_trailcnt);
> > > + i2c_wr32(sd, LINEINITCNT, csi_setting->lineinitcnt);
> > > + i2c_wr32(sd, LPTXTIMECNT, csi_setting->lptxtimecnt);
> > > + i2c_wr32(sd, TCLK_TRAILCNT, csi_setting->tclk_trailcnt);
> > > + i2c_wr32(sd, TXOPTIONCNTRL,
> > > + en_continuous_clk ? TXOPTIONCNTRL_CONTCLKMODE_MASK : 0);
> > > +
> > > + if (state->test)
> > > + tc38764_debug_pattern_80(sd);
> > > +
> > > + tc358746_dump_csi(sd, csi_setting);
> > > +}
> > > +
> > > +static void tc358746_enable_csi_module(struct v4l2_subdev *sd, int enable)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + struct tc358746_csi_param *csi_setting =
> > > + tc358746_g_cur_csi_settings(state);
> > > + unsigned int lanes = csi_setting->lane_num;
> > > + u32 val;
> > > +
> > > + if (!enable)
> > > + return;
> > > +
> > > + i2c_wr32(sd, STARTCNTRL, STARTCNTRL_START_MASK);
> > > + i2c_wr32(sd, CSI_START, CSI_START_STRT_MASK);
> > > +
> > > + val = CSI_CONTROL_NOL_1_MASK;
> > > + if (lanes == 2)
> > > + val = CSI_CONTROL_NOL_2_MASK;
> > > + else if (lanes == 3)
> > > + val = CSI_CONTROL_NOL_3_MASK;
> > > + else if (lanes == 4)
> > > + val = CSI_CONTROL_NOL_4_MASK;
> > > +
> > > + val |= CSI_CONTROL_CSI_MODE_MASK | CSI_CONTROL_TXHSMD_MASK;
> > > + tc358746_wr_csi_control(sd, val);
> > > +}
> > > +
> > > +static void tc358746_set_buffers(struct v4l2_subdev *sd)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + const struct tc358746_mbus_fmt *tc358746_mbusfmt =
> > > + tc358746_get_format(state->fmt.code);
> > > + unsigned int byte_per_line =
> > > + (state->fmt.width * tc358746_mbusfmt->bpp) / 8;
> > > +
> > > + i2c_wr16(sd, FIFOCTL, state->vb_fifo);
> > > + i2c_wr16(sd, WORDCNT, byte_per_line);
> > > + v4l2_dbg(1, debug, sd, "FIFOCTL 0x%02x: WORDCNT 0x%02x\n",
> > > + state->vb_fifo, byte_per_line);
> > > +}
> > > +
> > > +/* --------------- CORE OPS --------------- */
> > > +
> > > +static int tc358746_log_status(struct v4l2_subdev *sd)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + uint16_t sysctl = i2c_rd16(sd, SYSCTL);
> > > +
> > > + v4l2_info(sd, "-----Chip status-----\n");
> > > + v4l2_info(sd, "Chip ID: 0x%02lx\n",
> > > + (i2c_rd16(sd, CHIPID) & CHIPID_CHIPID_MASK) >> 8);
> > > + v4l2_info(sd, "Chip revision: 0x%02lx\n",
> > > + i2c_rd16(sd, CHIPID) & CHIPID_REVID_MASK);
> > > + v4l2_info(sd, "Sleep mode: %s\n", sysctl & SYSCTL_SLEEP_MASK ?
> > > + "on" : "off");
> > > +
> > > + v4l2_info(sd, "-----CSI-TX status-----\n");
> > > + v4l2_info(sd, "Waiting for particular sync signal: %s\n",
> > > + (i2c_rd16(sd, CSI_STATUS) & CSI_STATUS_S_WSYNC_MASK) ?
> > > + "yes" : "no");
> > > + v4l2_info(sd, "Transmit mode: %s\n",
> > > + (i2c_rd16(sd, CSI_STATUS) & CSI_STATUS_S_TXACT_MASK) ?
> > > + "yes" : "no");
> > > + v4l2_info(sd, "Stopped: %s\n",
> > > + (i2c_rd16(sd, CSI_STATUS) & CSI_STATUS_S_HLT_MASK) ?
> > > + "yes" : "no");
> > > + v4l2_info(sd, "Color space: %s\n",
> > > + state->fmt.code == MEDIA_BUS_FMT_UYVY8_2X8 ?
> > > + "YCbCr 422 8-bit" : "Unsupported");
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +#ifdef CONFIG_VIDEO_ADV_DEBUG
> > > +static void tc358746_print_register_map(struct v4l2_subdev *sd)
> > > +{
> > > + v4l2_info(sd, "0x0000-0x0050: Global Register\n");
> > > + v4l2_info(sd, "0x0056-0x0070: Rx Control Registers\n");
> > > + v4l2_info(sd, "0x0080-0x00F8: Rx Status Registers\n");
> > > + v4l2_info(sd, "0x0100-0x0150: Tx D-PHY Register\n");
> > > + v4l2_info(sd, "0x0204-0x0238: Tx PPI Register\n");
> > > + v4l2_info(sd, "0x040c-0x0518: Tx Control Register\n");
> > > +}
> > > +
> > > +static int tc358746_get_reg_size(u16 address)
> > > +{
> > > + if (address <= 0x00ff)
> > > + return 2;
> > > + else if ((address >= 0x0100) && (address <= 0x05FF))
> > > + return 4;
> > > + else
> > > + return 1;
> > > +}
> > > +
> > > +static int tc358746_g_register(struct v4l2_subdev *sd,
> > > + struct v4l2_dbg_register *reg)
> > > +{
> > > + if (reg->reg > 0xffff) {
> > > + tc358746_print_register_map(sd);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + reg->size = tc358746_get_reg_size(reg->reg);
> > > +
> > > + reg->val = i2c_rdreg(sd, reg->reg, reg->size);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int tc358746_s_register(struct v4l2_subdev *sd,
> > > + const struct v4l2_dbg_register *reg)
> > > +{
> > > + if (reg->reg > 0xffff) {
> > > + tc358746_print_register_map(sd);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + i2c_wrreg(sd, (u16)reg->reg, reg->val,
> > > + tc358746_get_reg_size(reg->reg));
> > > +
> > > + return 0;
> > > +}
> > > +#endif
> > > +
> > > +/* --------------- video ops --------------- */
> > > +
> > > +static int tc358746_s_power(struct v4l2_subdev *sd, int on)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > +
> > > + /*
> > > + * REF_01:
> > > + * Softreset don't reset configuration registers content but is needed
> >
> > "doesn't"
> >
> > > + * during power-on to trigger a csi LP-11 state change and during
> > > + * power-off to disable the csi-module.
> > > + */
> > > + tc358746_sreset(sd);
> > > +
> > > + if (state->fmt_changed) {
> > > + tc358746_set_buffers(sd);
> > > + tc358746_set_csi(sd);
> > > + tc358746_set_csi_color_space(sd);
> > > +
> > > + /* as recommend in REF_01 */
> > > + tc358746_sleep_mode(sd, 1);
> > > + tc358746_set_pll(sd);
> > > + tc358746_sleep_mode(sd, 0);
> > > +
> > > + state->fmt_changed = false;
> > > + }
> > > +
> > > + tc358746_enable_csi_lanes(sd, on);
> > > + tc358746_enable_csi_module(sd, on);
> > > + tc358746_sleep_mode(sd, !on);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int tc358746_s_stream(struct v4l2_subdev *sd, int enable)
> > > +{
> > > + tc358746_enable_stream(sd, enable);
> >
> > Could you use tc358746_enable_stream() directly as the s_stream op?
>
> Of course, added it for naming consistency since the enable_stream() is
> a internal function and I didn't wanted to mix those.
>
> > Note that you need to call the upstream sub-device's s_stream op from here
> > as well.
>
> I tought this is done by the host driver trough iterating over the whole
> graph?
>
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +/* --------------- pad ops --------------- */
> > > +
> > > +static int tc358746_enum_mbus_code(struct v4l2_subdev *sd,
> > > + struct v4l2_subdev_pad_config *cfg,
> > > + struct v4l2_subdev_mbus_code_enum *code)
> > > +{
> > > + if (code->index >= ARRAY_SIZE(tc358746_formats))
> > > + return -EINVAL;
> > > +
> > > + code->code = tc358746_formats[code->index].code;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static struct v4l2_mbus_framefmt *
> > > +__tc358746_get_pad_format(struct v4l2_subdev *sd,
> > > + struct v4l2_subdev_pad_config *cfg,
> > > + unsigned int pad, u32 which)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > +
> > > + switch (which) {
> > > + case V4L2_SUBDEV_FORMAT_TRY:
> > > + return v4l2_subdev_get_try_format(sd, cfg, pad);
> > > + case V4L2_SUBDEV_FORMAT_ACTIVE:
> > > + return &state->fmt;
> > > + default:
> > > + return NULL;
> > > + }
> > > +}
> > > +
> > > +static int tc358746_get_fmt(struct v4l2_subdev *sd,
> > > + struct v4l2_subdev_pad_config *cfg,
> > > + struct v4l2_subdev_format *format)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > +
> > > + if (format->pad != 0 && format->pad != 1)
> > > + return -EINVAL;
> > > +
> > > + format->format.code = state->fmt.code;
> > > + format->format.width = state->fmt.width;
> > > + format->format.height = state->fmt.height;
> > > + format->format.field = state->fmt.field;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int tc358746_set_fmt(struct v4l2_subdev *sd,
> > > + struct v4l2_subdev_pad_config *cfg,
> > > + struct v4l2_subdev_format *format)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + struct media_pad *pad = &state->pads[format->pad];
> > > + struct v4l2_mbus_framefmt *mbusformat;
> > > + const struct tc358746_mbus_fmt *tc358746_mbusformat;
> > > + unsigned int pclk, hblank;
> > > + unsigned int new_freq, cur_freq = v4l2_ctrl_g_ctrl(state->link_freq);
> > > + u16 vb_fifo;
> > > +
> > > + if (pad->flags == MEDIA_PAD_FL_SOURCE)
> > > + return tc358746_get_fmt(sd, cfg, format);
> > > +
> > > + mbusformat = __tc358746_get_pad_format(sd, cfg, format->pad,
> > > + format->which);
> > > + if (!mbusformat)
> > > + return -EINVAL;
> > > +
> > > + tc358746_mbusformat = tc358746_get_format(format->format.code);
> > > + if (!tc358746_mbusformat) {
> > > + format->format.code = tc358746_def_fmt.code;
> > > + tc358746_mbusformat = tc358746_get_format(format->format.code);
> > > + }
> > > +
> > > + /*
> > > + * Some sensors change their hblank and pclk value on different formats,
> > > + * so we need to request it again.
> > > + */
> > > + pclk = v4l2_ctrl_g_ctrl_int64(state->sensor_pclk_ctrl);
> > > + if (pclk != state->pclk) {
> > > + v4l2_dbg(1, debug, sd, "Update pclk %u -> %u\n",
> > > + state->pclk, pclk);
> > > + state->pclk = pclk;
> > > + }
> > > +
> > > + hblank = v4l2_ctrl_g_ctrl(state->sensor_hblank_ctrl);
> > > + if (hblank != state->hblank) {
> > > + v4l2_dbg(1, debug, sd, "Update hblank %u -> %u\n",
> > > + state->hblank, hblank);
> > > + state->hblank = hblank;
> > > + }
> > > +
> > > + /*
> > > + * Normaly the HW has no size limitations but we have to check if the
> > > + * csi timings are valid for this size. The timings can be adjust by the
> > > + * fifo size. If this doesn't work we have to do this check again with a
> > > + * other csi link frequency if it is possible.
> > > + */
> > > + new_freq = tc358746_adjust_timings(state, tc358746_mbusformat,
> > > + &format->format.width, &vb_fifo);
> > > +
> > > + /* Currently only a few YUV based formats are supported */
> > > + if (tc358746_format_supported(format->format.code))
> > > + format->format.code = MEDIA_BUS_FMT_UYVY8_2X8;
> > > +
> > > + /* Currently only non interleaved images are supported */
> > > + format->format.field = V4L2_FIELD_NONE;
> > > +
> > > + *mbusformat = format->format;
> > > +
> > > + if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
> > > + state->fmt_changed = true;
> > > + state->vb_fifo = vb_fifo;
> > > + if (new_freq != cur_freq)
> > > + v4l2_ctrl_s_ctrl(state->link_freq, new_freq);
> > > + }
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int
> > > +tc358746_link_validate(struct v4l2_subdev *sd, struct media_link *link,
> > > + struct v4l2_subdev_format *source_fmt,
> > > + struct v4l2_subdev_format *sink_fmt)
> > > +{
> > > + struct tc358746_state *state = to_state(sd);
> > > + const struct tc358746_mbus_fmt *tc358746_mbusformat;
> > > + unsigned int pclk, pclk_old = state->pclk;
> > > + unsigned int hblank, hblank_old = state->hblank;
> > > + int new_freq;
> > > + u16 vb_fifo;
> > > +
> > > + /*
> > > + * Only validate if the timings are changed, after the link was already
> > > + * initialized. This can be happen if the parallel sensor frame interval
> > > + * is changed. Format checks are perfomed by the common code.
> > > + */
> > > +
> > > + tc358746_mbusformat = tc358746_get_format(sink_fmt->format.code);
> > > + if (!tc358746_mbusformat)
> > > + return -EINVAL; /* Format was changed too and is invalid */
> > > +
> > > + pclk = v4l2_ctrl_g_ctrl_int64(state->sensor_pclk_ctrl);
> > > + if (pclk != state->pclk)
> > > + state->pclk = pclk;
> > > +
> > > + hblank = v4l2_ctrl_g_ctrl(state->sensor_hblank_ctrl);
> > > + if (hblank != state->hblank)
> > > + state->hblank = hblank;
> > > +
> > > + new_freq = tc358746_adjust_timings(state, tc358746_mbusformat,
> > > + &source_fmt->format.width, &vb_fifo);
> > > +
> > > + if (new_freq != v4l2_ctrl_g_ctrl(state->link_freq)) {
> > > + /*
> > > + * This can lead into undefined behaviour, so we don't support
> > > + * dynamic changes due to a to late re-configuration.
> > > + */
> > > + state->pclk = pclk_old;
> > > + state->hblank = hblank_old;
> > > +
> > > + return -EINVAL;
> > > + }
> > > +
> > > + state->fmt_changed = true;
> > > + state->vb_fifo = vb_fifo;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int tc358764_s_ctrl(struct v4l2_ctrl *ctrl)
> > > +{
> > > + struct tc358746_state *state = container_of(ctrl->handler,
> > > + struct tc358746_state, hdl);
> > > + struct v4l2_subdev *sd = &state->sd;
> > > +
> > > + switch (ctrl->id) {
> > > + case V4L2_CID_LINK_FREQ:
> > > + v4l2_info(sd, "Update link-frequency %llu -> %llu\n",
> > > + state->link_frequencies[ctrl->cur.val],
> > > + state->link_frequencies[ctrl->val]);
> > > +
> > > + return 0;
> > > + case V4L2_CID_TEST_PATTERN:
> > > + state->test = ctrl->val;
> > > + return 0;
> > > + }
> > > +
> > > + return -EINVAL;
> > > +}
> > > +
> > > +static int tc358746_link_setup(struct media_entity *entity,
> > > + const struct media_pad *local,
> > > + const struct media_pad *remote, u32 flags)
> > > +{
> > > + struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
> > > + struct v4l2_subdev *ps_sd = media_entity_to_v4l2_subdev(remote->entity);
> > > + struct tc358746_state *state = to_state(sd);
> > > + struct v4l2_ctrl *ctrl;
> > > +
> > > + /* no special requirements on source pads */
> > > + if (local->flags & MEDIA_PAD_FL_SOURCE)
> > > + return 0;
> > > +
> > > + v4l2_dbg(1, debug, sd, "link setup '%s':%d->'%s':%d[%d]",
> > > + remote->entity->name, remote->index, local->entity->name,
> > > + local->index, flags & MEDIA_LNK_FL_ENABLED);
> > > +
> > > + /*
> > > + * The remote parallel sensor must support pixel rate and hblank query
> > > + */
> > > + ctrl = v4l2_ctrl_find(ps_sd->ctrl_handler, V4L2_CID_PIXEL_RATE);
> > > + if (!ctrl) {
> > > + v4l2_err(sd, "Subdev %s must support V4L2_CID_PIXEL_RATE\n",
> > > + ps_sd->name);
> > > + return -EINVAL;
> > > + }
> > > + state->pclk = v4l2_ctrl_g_ctrl_int64(ctrl);
> > > + state->sensor_pclk_ctrl = ctrl;
> > > +
> > > + ctrl = v4l2_ctrl_find(ps_sd->ctrl_handler, V4L2_CID_HBLANK);
> > > + if (!ctrl) {
> > > + v4l2_err(sd, "Subdev %s must support V4L2_CID_HBLANK\n",
> > > + ps_sd->name);
> > > + return -EINVAL;
> > > + }
> > > + state->hblank = v4l2_ctrl_g_ctrl(ctrl);
> > > + state->sensor_hblank_ctrl = ctrl;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +/* -------------------------------------------------------------------------- */
> > > +
> > > +static const struct v4l2_ctrl_ops tc358764_ctrl_ops = {
> > > + .s_ctrl = tc358764_s_ctrl,
> > > +};
> > > +
> > > +static const struct v4l2_subdev_core_ops tc358746_core_ops = {
> > > + .log_status = tc358746_log_status,
> > > +#ifdef CONFIG_VIDEO_ADV_DEBUG
> > > + .g_register = tc358746_g_register,
> > > + .s_register = tc358746_s_register,
> > > +#endif
> > > + .s_power = tc358746_s_power,
> > > +};
> > > +
> > > +static const struct v4l2_subdev_video_ops tc358746_video_ops = {
> > > + .s_stream = tc358746_s_stream,
> > > +};
> > > +
> > > +static const struct v4l2_subdev_pad_ops tc358746_pad_ops = {
> > > + .enum_mbus_code = tc358746_enum_mbus_code,
> > > + .set_fmt = tc358746_set_fmt,
> > > + .get_fmt = tc358746_get_fmt,
> > > + .link_validate = tc358746_link_validate,
> > > +};
> > > +
> > > +static const struct v4l2_subdev_ops tc358746_ops = {
> > > + .core = &tc358746_core_ops,
> > > + .video = &tc358746_video_ops,
> > > + .pad = &tc358746_pad_ops,
> > > +};
> > > +
> > > +static const struct media_entity_operations tc358746_entity_ops = {
> > > + .link_setup = &tc358746_link_setup,
> > > + .link_validate = &v4l2_subdev_link_validate,
> > > +};
> > > +
> > > +/* --------------- PROBE / REMOVE --------------- */
> > > +
> > > +static int tc358746_set_lane_settings(struct tc358746_state *state,
> > > + struct v4l2_fwnode_endpoint *fw)
> > > +{
> > > + struct v4l2_subdev *sd = &state->sd;
> > > + int i;
> >
> > unsigned int ?
> >
> > > +
> > > + for (i = 0; i < fw->nr_of_link_frequencies; i++) {
> > > + struct tc358746_csi_param *s =
> > > + &state->link_freq_settings[i];
> > > + u32 bps_pr_lane;
> > > +
> > > + state->link_frequencies[i] = fw->link_frequencies[i];
> > > +
> > > + /*
> > > + * The CSI bps per lane must be between 62.5 Mbps and 1 Gbps.
> > > + * bps_pr_lane = 2 * link_freq, because MIPI data lane is double
> > > + * data rate.
> > > + */
> > > + bps_pr_lane = 2 * fw->link_frequencies[i];
> > > + if (bps_pr_lane < 62500000U || bps_pr_lane > 1000000000U) {
> > > + v4l2_err(sd, "unsupported bps per lane: %u bps\n",
> > > + bps_pr_lane);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + if (bps_pr_lane > 500000000)
> > > + s->speed_range = 0;
> > > + else if (bps_pr_lane > 250000000)
> > > + s->speed_range = 1;
> > > + else if (bps_pr_lane > 125000000)
> > > + s->speed_range = 2;
> > > + else
> > > + s->speed_range = 3;
> > > +
> > > + s->unit_clk_hz = state->pllinclk_hz >> s->speed_range;
> > > + s->unit_clk_mul = bps_pr_lane / s->unit_clk_hz;
> > > + s->speed_per_lane = bps_pr_lane;
> > > + s->lane_num = fw->bus.mipi_csi2.num_data_lanes;
> > > + s->is_continuous_clk = fw->bus.mipi_csi2.flags &
> > > + V4L2_MBUS_CSI2_CONTINUOUS_CLOCK;
> > > +
> > > + if (s->speed_per_lane != 432000000U)
> > > + v4l2_warn(sd, "untested bps per lane: %u bps\n",
> > > + s->speed_per_lane);
> > > +
> > > + v4l2_dbg(2, debug, sd, "lane setting %d\n", i);
> > > + v4l2_dbg(2, debug, sd,
> > > + "unit_clk %uHz: unit_clk_mul %u: speed_range %u: speed_per_lane(bps/lane) %u: csi_lange_numbers %u\n",
> > > + s->unit_clk_hz, s->unit_clk_mul, s->speed_range,
> > > + s->speed_per_lane, s->lane_num);
> > > + }
> > > +
> > > + state->link_frequencies_num = fw->nr_of_link_frequencies;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static void tc358746_gpio_reset(struct tc358746_state *state)
> > > +{
> > > + usleep_range(5000, 10000);
> > > + gpiod_set_value(state->reset_gpio, 1);
> > > + usleep_range(1000, 2000);
> > > + gpiod_set_value(state->reset_gpio, 0);
> > > + msleep(20);
> > > +}
> > > +
> > > +static int tc358746_apply_fw(struct tc358746_state *state)
> > > +{
> > > + struct v4l2_subdev *sd = &state->sd;
> > > + struct tc358746_csi_param *csi_setting;
> > > + int err, i;
> >
> > unsigned int i
>
> Yes.
>
> > > +
> > > + for (i = 0; i < state->link_frequencies_num; i++) {
> > > + csi_setting = &state->link_freq_settings[i];
> > > +
> > > + err = tc358746_calculate_csi_txtimings(state, csi_setting);
> > > + if (err) {
> > > + v4l2_err(sd, "Failed to calc csi-tx tminings\n");
> > > + return err;
> > > + }
> > > + }
> > > +
> > > + /*
> > > + * Set it to the hw default value. The correct value will be set during
> > > + * set_fmt(), since it depends on the pclk and and the resulution.
> > > + */
> > > + state->vb_fifo = 1;
> > > +
> > > + err = clk_prepare_enable(state->refclk);
> > > + if (err) {
> > > + v4l2_err(sd, "Failed to enable clock\n");
> > > + return err;
> > > + }
> >
> > Is there a need to keep the clock running even if the device is not
> > streaming? Please consider adding runtime PM support. That's not strictly
> > needed for the patch to be merged though IMO.
>
> Thats a good point. The Chip can act as clk-provider fo rother devices.
> So I would probably say yes.
>
> > > +
> > > + if (state->reset_gpio)
> > > + tc358746_gpio_reset(state);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int tc358746_probe_fw(struct tc358746_state *state)
> > > +{
> > > + struct device *dev = &state->i2c_client->dev;
> > > + struct v4l2_subdev *sd = &state->sd;
> > > + struct v4l2_fwnode_endpoint endpoint = {
> > > + .bus_type = V4L2_MBUS_CSI2_DPHY,
> > > + };
> > > + struct fwnode_handle *fw_node;
> > > + unsigned int refclk, pllinclk;
> > > + unsigned char pll_prediv;
> > > + int ret = -EINVAL;
> >
> > ret is always assigned elsewhere; no need to initialise.
> >
> > > +
> > > + /* Parse all clocks */
> > > + state->refclk = devm_clk_get(dev, NULL);
> > > + if (IS_ERR(state->refclk)) {
> > > + if (PTR_ERR(state->refclk) != -EPROBE_DEFER)
> > > + v4l2_err(sd, "failed to get refclk: %ld\n",
> > > + PTR_ERR(state->refclk));
> > > + return PTR_ERR(state->refclk);
> > > + }
> > > +
> > > + refclk = clk_get_rate(state->refclk);
> > > + if (refclk < 6000000 || refclk > 40000000) {
> > > + v4l2_err(sd, "Invalid refclk %u, valid range: 6-40 MHz\n",
> > > + refclk);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + /*
> > > + * The PLL input clock is obtained by dividing refclk by pll_prd.
> > > + * It must be between 4 MHz and 40 MHz, lower frequency is better.
> > > + */
> > > + pll_prediv = DIV_ROUND_CLOSEST(refclk, 4000000);
> > > + if (pll_prediv < 1 || pll_prediv > 16) {
> > > + v4l2_err(sd, "Invalid pll pre-divider value: %d\n", pll_prediv);
> > > + return -EINVAL;
> > > + }
> > > + state->pll_prd = pll_prediv;
> > > +
> > > + pllinclk = DIV_ROUND_CLOSEST(refclk, pll_prediv);
> > > + if (pllinclk < 4000000 || pllinclk > 40000000) {
> > > + v4l2_err(sd, "Invalid pll input clock: %d Hz\n", pllinclk);
> > > + return -EINVAL;
> > > + }
> > > + state->pllinclk_hz = pllinclk;
> > > +
> > > + /* Now parse the fw-node */
> > > + fwnode_graph_for_each_endpoint(dev_fwnode(dev), fw_node) {
> > > + struct fwnode_endpoint fw_ep;
> > > +
> > > + ret = fwnode_graph_parse_endpoint(fw_node, &fw_ep);
> > > + if (ret)
> > > + return -EINVAL;
> > > +
> > > + /* Get downstream endpoint */
> > > + if (fw_ep.port == 1)
> > > + break;
> >
> > You could use fwnode_graph_get_endpoint_by_id() instead of the loop.
>
> Of course.
>
> > > + }
> > > +
> > > + if (!fw_node) {
> > > + v4l2_err(sd, "Missing endpoint node\n");
> > > + return -EINVAL;
> > > + }
> > > +
> > > + ret = v4l2_fwnode_endpoint_alloc_parse(fw_node, &endpoint);
> > > + if (ret) {
> > > + v4l2_err(sd, "Failed to parse endpoint %d\n", ret);
> > > + return ret;
> > > + }
> > > +
> > > + state->csi_dir = TC358746_CSI_TX;
> > > +
> > > + if (endpoint.bus.mipi_csi2.num_data_lanes == 0 ||
> > > + endpoint.nr_of_link_frequencies == 0) {
> > > + v4l2_err(sd, "Missing CSI-2 properties in endpoint\n");
> > > + ret = -EINVAL;
> > > + goto free_ep;
> > > + }
> > > +
> > > + if (endpoint.bus.mipi_csi2.num_data_lanes > 4) {
> > > + v4l2_err(sd, "Invalid number of lanes\n");
> > > + ret = -EINVAL;
> > > + goto free_ep;
> > > + }
> > > +
> > > + state->link_freq_settings =
> > > + devm_kcalloc(dev, endpoint.nr_of_link_frequencies,
> > > + sizeof(*state->link_freq_settings), GFP_KERNEL);
> > > + if (!state->link_freq_settings) {
> > > + ret = -ENOMEM;
> > > + goto free_ep;
> > > + }
> > > +
> > > + state->link_frequencies =
> > > + devm_kcalloc(dev, endpoint.nr_of_link_frequencies,
> > > + sizeof(*state->link_frequencies), GFP_KERNEL);
> > > + if (!state->link_frequencies) {
> > > + ret = -ENOMEM;
> > > + goto free_ep;
> > > + }
> > > +
> > > + ret = tc358746_set_lane_settings(state, &endpoint);
> > > + if (ret)
> > > + goto free_ep;
> > > +
> > > + state->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> > > + GPIOD_OUT_LOW);
> > > + if (IS_ERR(state->reset_gpio)) {
> > > + v4l2_err(sd, "failed to get reset gpio\n");
> > > + ret = PTR_ERR(state->reset_gpio);
> > > + goto free_ep;
> > > + }
> > > +
> > > + ret = 0;
> > > +
> > > +free_ep:
> > > + v4l2_fwnode_endpoint_free(&endpoint);
> > > + return ret;
> > > +}
> > > +
> > > +static int tc358746_parse_endpoint(struct device *dev,
> > > + struct v4l2_fwnode_endpoint *vep,
> > > + struct v4l2_async_subdev *asd)
> > > +{
> > > + struct v4l2_subdev *sd = dev_get_drvdata(dev);
> > > + struct tc358746_state *state = to_state(sd);
> > > +
> > > + if (!fwnode_device_is_available(asd->match.fwnode)) {
> > > + v4l2_err(sd, "remote is not available\n");
> > > + return -ENOTCONN;
> > > + }
> > > +
> > > + if (state->csi_dir == TC358746_CSI_TX &&
> > > + vep->bus_type != V4L2_MBUS_PARALLEL) {
> > > + v4l2_err(sd, "invalid bus type, must be PARALLEL\n");
> > > + return -ENOTCONN;
> > > + }
> > > +
> > > + return 0;
> > > +};
> > > +
> > > +static int tc358746_async_register(struct v4l2_subdev *sd)
> > > +{
> > > + unsigned int port = 0;
> > > +
> > > + return v4l2_async_register_fwnode_subdev(
> > > + sd, sizeof(struct v4l2_async_subdev), &port, 1,
> > > + tc358746_parse_endpoint);
> >
> > Please move this to the caller instead.
>
> Okay.
>
> > > +
> > > +}
> > > +
> > > +static const char * const tc358764_test_pattern_menu[] = {
> > > + "Disabled",
> > > + "80 Pixel Color Bars",
> > > +};
> > > +
> > > +static int tc358746_probe(struct i2c_client *client)
> > > +{
> > > + struct tc358746_state *state;
> > > + struct v4l2_subdev *sd;
> > > + int err;
> > > +
> > > + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
> > > + return -EIO;
> > > +
> > > + state = devm_kzalloc(&client->dev, sizeof(*state), GFP_KERNEL);
> > > + if (!state)
> > > + return -ENOMEM;
> > > +
> > > + state->i2c_client = client;
> >
> > You can use v4l2_get_subdevdata() to obtain the I²C client; no need to
> > store it separately.
>
> Yes, your're right. I change that.
>
> > > + sd = &state->sd;
> > > + v4l2_i2c_subdev_init(sd, client, &tc358746_ops);
> > > + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > > +
> > > + err = tc358746_probe_fw(state);
> > > + if (err)
> > > + return err;
> > > +
> > > + err = tc358746_apply_fw(state);
> > > + if (err)
> > > + return err;
> > > +
> > > + if (((i2c_rd16(sd, CHIPID) & CHIPID_CHIPID_MASK) >> 8) != 0x44) {
> > > + v4l2_info(sd, "not a TC358746 on address 0x%x\n",
> > > + client->addr << 1);
> > > + err = -ENODEV;
> > > + goto err_clk;
> > > + }
> > > +
> > > + v4l2_ctrl_handler_init(&state->hdl, 2);
> > > +
> > > + v4l2_ctrl_new_std_menu_items(&state->hdl,
> > > + &tc358764_ctrl_ops, V4L2_CID_TEST_PATTERN,
> > > + ARRAY_SIZE(tc358764_test_pattern_menu) - 1, 0, 0,
> > > + tc358764_test_pattern_menu);
> > > +
> > > + state->link_freq =
> > > + v4l2_ctrl_new_int_menu(&state->hdl, &tc358764_ctrl_ops,
> > > + V4L2_CID_LINK_FREQ,
> > > + state->link_frequencies_num - 1,
> > > + TC358746_DEF_LINK_FREQ,
> > > + state->link_frequencies);
> > > +
> > > +
> > > + sd->ctrl_handler = &state->hdl;
> > > + if (state->hdl.error) {
> > > + err = state->hdl.error;
> > > + goto err_hdl;
> > > + }
> > > +
> > > + state->pads[0].flags = MEDIA_PAD_FL_SINK;
> > > + state->pads[1].flags = MEDIA_PAD_FL_SOURCE;
> > > + sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
> > > + sd->entity.ops = &tc358746_entity_ops;
> > > + err = media_entity_pads_init(&sd->entity, 2, state->pads);
> > > + if (err < 0)
> > > + goto err_hdl;
> > > +
> > > + mutex_init(&state->confctl_mutex);
> > > +
> > > + state->fmt = tc358746_def_fmt;
> > > +
> > > + /* Apply default settings */
> > > + tc358746_sreset(sd);
> > > + tc358746_set_buffers(sd);
> > > + tc358746_set_csi(sd);
> > > + tc358746_set_csi_color_space(sd);
> > > + tc358746_sleep_mode(sd, 1);
> > > + tc358746_set_pll(sd);
> > > + tc358746_enable_stream(sd, 0);
> > > +
> > > + err = tc358746_async_register(sd);
> > > + if (err < 0)
> > > + goto err_mutex;
> > > +
> > > + v4l2_info(sd, "%s found @ 0x%x (%s)\n", client->name,
> > > + client->addr << 1, client->adapter->name);
> > > +
> > > + return 0;
> > > +
> > > +err_mutex:
> > > + mutex_destroy(&state->confctl_mutex);
> > > +err_hdl:
> > > + media_entity_cleanup(&sd->entity);
> > > + v4l2_ctrl_handler_free(&state->hdl);
> > > +err_clk:
> > > + clk_disable_unprepare(state->refclk);
> > > +
> > > + return err;
> > > +}
> > > +
> > > +static int tc358746_remove(struct i2c_client *client)
> > > +{
> > > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > > + struct tc358746_state *state = to_state(sd);
> > > +
> > > + v4l2_async_unregister_subdev(sd);
> > > + v4l2_device_unregister_subdev(sd);
> > > + mutex_destroy(&state->confctl_mutex);
> > > + media_entity_cleanup(&sd->entity);
> > > + v4l2_ctrl_handler_free(&state->hdl);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static const struct of_device_id __maybe_unused tc358746_of_match[] = {
> > > + { .compatible = "toshiba,tc358746" },
> > > + { },
> > > +};
> > > +MODULE_DEVICE_TABLE(of, tc358746_of_match);
> > > +
> > > +static struct i2c_driver tc358746_driver = {
> > > + .driver = {
> > > + .name = "tc358746",
> > > + .of_match_table = of_match_ptr(tc358746_of_match),
> >
> > No need for of_patch_ptr() here.
>
> Okay.
>
>
> Thanks for the review =)
>
> Regards,
> Marco
>
> >
> > > + },
> > > + .probe_new = tc358746_probe,
> > > + .remove = tc358746_remove,
> > > +};
> > > +
> > > +module_i2c_driver(tc358746_driver);
> > > diff --git a/drivers/media/i2c/tc358746_regs.h b/drivers/media/i2c/tc358746_regs.h
> > > new file mode 100644
> > > index 000000000000..9232d00d0e92
> > > --- /dev/null
> > > +++ b/drivers/media/i2c/tc358746_regs.h
> > > @@ -0,0 +1,208 @@
> > > +/* SPDX-License-Identifier: GPL-2.0-only */
> > > +/*
> > > + * tc358746 - Toshiba Parallel to CSI-2 bridge - register names and bit masks
> > > + *
> > > + * Convention:
> > > + * <REGISTER>
> > > + * <REGISTER>_<BITFIELD>_MASK
> > > + * <REGISTER>_<BITFIELD>_<VALUE>
> > > + * <REGISTER>_<BITFIELD>_SET(val = <REGISTER>_<BITFIELD>_<VALUE>)
> > > + *
> > > + * References:
> > > + * REF_01:
> > > + * - TC358746AXBG/TC358748XBG/TC358748IXBG Functional Specification Rev 1.2
> > > + */
> > > +
> > > +#ifndef __TC358746_REGS_H
> > > +#define __TC358746_REGS_H
> > > +
> > > +#define CHIPID 0x0000
> > > +#define CHIPID_CHIPID_MASK GENMASK(15, 8)
> > > +#define CHIPID_REVID_MASK GENMASK(7, 0)
> > > +
> > > +#define SYSCTL 0x0002
> > > +#define SYSCTL_SLEEP_MASK BIT(1)
> > > +#define SYSCTL_SRESET_MASK BIT(0)
> > > +
> > > +#define CONFCTL 0x0004
> > > +#define CONFCTL_TRIEN_MASK BIT(15)
> > > +#define CONFCTL_INTE2N_MASK BIT(13)
> > > +#define CONFCTL_BT656EN_MASK BIT(12)
> > > +#define CONFCTL_PDATAF_MASK GENMASK(9, 8)
> > > +#define CONFCTL_PDATAF_SET(val) (((val << 8) & CONFCTL_PDATAF_MASK))
> > > +#define CONFCTL_PDATAF_MODE0 0
> > > +#define CONFCTL_PDATAF_MODE1 1
> > > +#define CONFCTL_PDATAF_MODE2 2
> > > +#define CONFCTL_PPEN_MASK BIT(6)
> > > +#define CONFCTL_VVALIDP_MASK BIT(5)
> > > +#define CONFCTL_HVALIDP_MASK BIT(4)
> > > +#define CONFCTL_PCLKP_MASK BIT(3)
> > > +#define CONFCTL_AUTO_MASK BIT(2)
> > > +#define CONFCTL_DATALANE_MASK GENMASK(1, 0)
> > > +#define CONFCTL_DATALANE_1 0
> > > +#define CONFCTL_DATALANE_2 1
> > > +#define CONFCTL_DATALANE_3 2
> > > +#define CONFCTL_DATALANE_4 3
> > > +
> > > +#define FIFOCTL 0x0006
> > > +#define DATAFMT 0x0008
> > > +#define DATAFMT_PDFMT_RAW8 0
> > > +#define DATAFMT_PDFMT_RAW10 1
> > > +#define DATAFMT_PDFMT_RAW12 2
> > > +#define DATAFMT_PDFMT_RGB888 3
> > > +#define DATAFMT_PDFMT_RGB666 4
> > > +#define DATAFMT_PDFMT_RGB565 5
> > > +#define DATAFMT_PDFMT_YCBCRFMT_422_8_BIT 6
> > > +#define DATAFMT_PDFMT_RAW14 8
> > > +#define DATAFMT_PDFMT_YCBCRFMT_422_10_BIT 9
> > > +#define DATAFMT_PDFMT_YCBCRFMT_444 10
> > > +#define DATAFMT_PDFMT_MASK GENMASK(7, 4)
> > > +#define DATAFMT_PDFMT_SET(val) (((val) << 4) & DATAFMT_PDFMT_MASK)
> > > +#define DATAFMT_UDT_EN_MASK BIT(0)
> > > +
> > > +#define MCLKCTL 0x000c
> > > +#define MCLKCTL_MCLK_HIGH_MASK GENMASK(15, 8)
> > > +#define MCLKCTL_MCLK_HIGH_SET(val) ((((val) - 1) << 8) & MCLKCTL_MCLK_HIGH_MASK)
> > > +#define MCLKCTL_MCLK_LOW_MASK GENMASK(7, 0)
> > > +#define MCLKCTL_MCLK_LOW_SET(val) (((val) - 1) & MCLKCTL_MCLK_LOW_MASK)
> > > +
> > > +#define PLLCTL0 0x0016
> > > +#define PLLCTL0_PLL_PRD_MASK GENMASK(15, 12)
> > > +#define PLLCTL0_PLL_PRD_SET(prd) ((((prd) - 1) << 12) & PLLCTL0_PLL_PRD_MASK)
> > > +#define PLLCTL0_PLL_FBD_MASK GENMASK(8, 0)
> > > +#define PLLCTL0_PLL_FBD_SET(fbd) (((fbd) - 1) & PLLCTL0_PLL_FBD_MASK)
> > > +
> > > +#define PLLCTL1 0x0018
> > > +#define PLLCTL1_PLL_FRS_MASK GENMASK(11, 10)
> > > +#define PLLCTL1_PLL_FRS_SET(frs) (((frs) << 10) & PLLCTL1_PLL_FRS_MASK)
> > > +#define PLLCTL1_PLL_LBWS_MASK GENMASK(9, 8)
> > > +#define PLLCTL1_LFBREN_MASK BIT(6)
> > > +#define PLLCTL1_BYPCKEN_MASK BIT(5)
> > > +#define PLLCTL1_CKEN_MASK BIT(4)
> > > +#define PLLCTL1_RESETB_MASK BIT(1)
> > > +#define PLLCTL1_PLL_EN_MASK BIT(0)
> > > +
> > > +#define CLKCTL 0x0020
> > > +#define CLKCTL_MCLKDIV_MASK GENMASK(3, 2)
> > > +#define CLKCTL_MCLKDIV_SET(val) ((val << 2) & CLKCTL_MCLKDIV_MASK)
> > > +#define CLKCTL_MCLKDIV_8 0
> > > +#define CLKCTL_MCLKDIV_4 1
> > > +#define CLKCTL_MCLKDIV_2 2
> > > +
> > > +#define WORDCNT 0x0022
> > > +#define PP_MISC 0x0032
> > > +#define PP_MISC_FRMSTOP_MASK BIT(15)
> > > +#define PP_MISC_RSTPTR_MASK BIT(14)
> > > +
> > > +#define CSI2TX_DATA_TYPE 0x0050
> > > +#define MIPI_PHY_STATUS 0x0062
> > > +#define CSI2_ERROR_STATUS 0x0064
> > > +#define CSI2_ERR_EN 0x0066
> > > +#define CSI2_IDID_ERROR 0x006c
> > > +#define DBG_ACT_LINE_CNT 0x00e0
> > > +#define DBG_LINE_WIDTH 0x00e2
> > > +#define DBG_VERT_BLANK_LINE_CNT 0x00e4
> > > +#define DBG_VIDEO_DATA 0x00e8
> > > +#define FIFOSTATUS 0x00F8
> > > +
> > > +#define CLW_CNTRL 0x0140
> > > +#define CLW_CNTRL_CLW_LANEDISABLE_MASK BIT(0)
> > > +
> > > +#define D0W_CNTRL 0x0144
> > > +#define D0W_CNTRL_D0W_LANEDISABLE_MASK BIT(0)
> > > +
> > > +#define D1W_CNTRL 0x0148
> > > +#define D1W_CNTRL_D1W_LANEDISABLE_MASK BIT(0)
> > > +
> > > +#define D2W_CNTRL 0x014C
> > > +#define D2W_CNTRL_D2W_LANEDISABLE_MASK BIT(0)
> > > +
> > > +#define D3W_CNTRL 0x0150
> > > +#define D2W_CNTRL_D3W_LANEDISABLE_MASK BIT(0)
> > > +
> > > +#define STARTCNTRL 0x0204
> > > +#define STARTCNTRL_START_MASK BIT(0)
> > > +
> > > +#define LINEINITCNT 0x0210
> > > +#define LPTXTIMECNT 0x0214
> > > +#define TCLK_HEADERCNT 0x0218
> > > +#define TCLK_HEADERCNT_TCLK_ZEROCNT_MASK GENMASK(15, 8)
> > > +#define TCLK_HEADERCNT_TCLK_PREPARECNT_MASK GENMASK(6, 0)
> > > +#define TCLK_HEADERCNT_TCLK_ZEROCNT_SET(val) ((val << 8) & TCLK_HEADERCNT_TCLK_ZEROCNT_MASK)
> > > +#define TCLK_HEADERCNT_TCLK_PREPARECNT_SET(val) (val & TCLK_HEADERCNT_TCLK_PREPARECNT_MASK)
> > > +
> > > +#define TCLK_TRAILCNT 0x021C
> > > +#define THS_HEADERCNT 0x0220
> > > +#define THS_HEADERCNT_THS_ZEROCNT_MASK GENMASK(14, 8)
> > > +#define THS_HEADERCNT_THS_PREPARECNT_MASK GENMASK(6, 0)
> > > +#define THS_HEADERCNT_THS_ZEROCNT_SET(val) ((val << 8) & THS_HEADERCNT_THS_ZEROCNT_MASK)
> > > +#define THS_HEADERCNT_THS_PREPARECNT_SET(val) (val & THS_HEADERCNT_THS_PREPARECNT_MASK)
> > > +
> > > +#define TWAKEUP 0x0224
> > > +#define TCLK_POSTCNT 0x0228
> > > +#define THS_TRAILCNT 0x022C
> > > +#define HSTXVREGCNT 0x0230
> > > +#define HSTXVREGEN 0x0234
> > > +#define HSTXVREGEN_D3M_HSTXVREGEN_MASK BIT(4)
> > > +#define HSTXVREGEN_D2M_HSTXVREGEN_MASK BIT(3)
> > > +#define HSTXVREGEN_D1M_HSTXVREGEN_MASK BIT(2)
> > > +#define HSTXVREGEN_D0M_HSTXVREGEN_MASK BIT(1)
> > > +#define HSTXVREGEN_CLM_HSTXVREGEN_MASK BIT(0)
> > > +
> > > +#define TXOPTIONCNTRL 0x0238
> > > +#define TXOPTIONCNTRL_CONTCLKMODE_MASK BIT(0)
> > > +
> > > +#define CSI_CONTROL 0x040C
> > > +#define CSI_CONTROL_CSI_MODE_MASK BIT(15)
> > > +#define CSI_CONTROL_HTXTOEN_MASK BIT(10)
> > > +#define CSI_CONTROL_TXHSMD_MASK BIT(7)
> > > +#define CSI_CONTROL_NOL_MASK GENMASK(2, 1)
> > > +#define CSI_CONTROL_NOL_1_MASK 0
> > > +#define CSI_CONTROL_NOL_2_MASK BIT(1)
> > > +#define CSI_CONTROL_NOL_3_MASK BIT(2)
> > > +#define CSI_CONTROL_NOL_4_MASK (BIT(1) | BIT(2))
> > > +#define CSI_CONTROL_EOTDIS_MASK BIT(0)
> > > +
> > > +#define CSI_STATUS 0x0410
> > > +#define CSI_STATUS_S_WSYNC_MASK BIT(10)
> > > +#define CSI_STATUS_S_TXACT_MASK BIT(9)
> > > +#define CSI_STATUS_S_HLT_MASK BIT(0)
> > > +
> > > +#define CSI_INT 0x0414
> > > +#define CSI_INT_INTHLT_MASK BIT(3)
> > > +#define CSI_INT_INTER_MASK BIT(2)
> > > +
> > > +#define CSI_INT_ENA 0x0418
> > > +#define CSI_INT_ENA_IENHLT_MASK BIT(3)
> > > +#define CSI_INT_ENA_IENER_MASK BIT(2)
> > > +
> > > +#define CSI_ERR 0x044C
> > > +#define CSI_ERR_INER_MASK BIT(9)
> > > +#define CSI_ERR_WCER_MASK BIT(8)
> > > +#define CSI_ERR_QUNK_MASK BIT(4)
> > > +#define CSI_ERR_TXBRK_MASK BIT(1)
> > > +
> > > +#define CSI_ERR_INTENA 0x0450
> > > +#define CSI_ERR_HALT 0x0454
> > > +#define CSI_CONFW 0x0500
> > > +#define CSI_CONFW_MODE_MASK GENMASK(31, 29)
> > > +#define CSI_CONFW_MODE_SET_MASK (BIT(31) | BIT(29))
> > > +#define CSI_CONFW_MODE_CLEAR_MASK (BIT(31) | BIT(30))
> > > +#define CSI_CONFW_ADDRESS_MASK GENMASK(28, 24)
> > > +#define CSI_CONFW_ADDRESS_CSI_CONTROL_MASK (BIT(24) | BIT(25))
> > > +#define CSI_CONFW_ADDRESS_CSI_INT_ENA_MASK (BIT(25) | BIT(26))
> > > +#define CSI_CONFW_ADDRESS_CSI_ERR_INTENA_MASK (BIT(28) | BIT(26))
> > > +#define CSI_CONFW_ADDRESS_CSI_ERR_HALT_MASK (BIT(28) | BIT(26) | BIT(24))
> > > +#define CSI_CONFW_DATA_MASK GENMASK(15, 0)
> > > +
> > > +#define CSIRESET 0x0504
> > > +#define CSIRESET_RESET_CNF_MASK BIT(1)
> > > +#define CSIRESET_RESET_MODULE_MASK BIT(0)
> > > +
> > > +#define CSI_INT_CLR 0x050C
> > > +#define CSI_INT_CLR_ICRER_MASK BIT(2)
> > > +
> > > +#define CSI_START 0x0518
> > > +#define CSI_START_STRT_MASK BIT(0)
> > > +
> > > +#endif
> >
> > --
> > Kind regards,
> >
> > Sakari Ailus
> > sakari.ailus@xxxxxxxxxxxxxxx
> >
>
> --
> Pengutronix e.K. | |
> Industrial Linux Solutions | http://www.pengutronix.de/ |
> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
