On 8/8/19 11:02 AM, Steve Longerbeam wrote:
On 8/8/19 1:53 AM, Philipp Zabel wrote:
Hi Sakari,
On Thu, 2019-08-08 at 11:26 +0300, Sakari Ailus wrote:
[...]
Have you checked how it works if you simply leave out this test?
Whether this works or not depends on the sensor used, and for some
sensor/drivers may depend on timing (or random factors influencing it).
See below.
[...]
Some devices can be commanded to enter LP-11 state but some will just
briefly visit that state. The LP-11 state is mandatory but software
should
not be involved in detecting it if at all possible.
This is a good point. Devices that can be set to LP-11 state
immediately, but that don't stay there long enough (either because they
wait for less than the required by spec 100µs, or because system load
causes this check to be executed too late) may end up working reliably
even though the warning fires.
So if the hardware does not require further initialisation to be
done in
LP-11 state, you should remove the check.
We had to fix at least OV5645 and OV5640 recently because of this,
and I can imagine more drivers will have the same issue.
This is actually an issue in the IMX driver (or hardware), not in the
sensor driver. It may be that sometimes it's easier to work around
it in
the sensor driver.
So, I'd like to know whether the check itself is a driver bug, or
something
that the hardware requires. The fact that you're sending this patch
suggests the former.
This is something that the hardware requires, according to the reference
manual. See the comment in drivers/staging/media/imx/imx6-mipi-csi2.c,
especially step 5.:
/*
* The required sequence of MIPI CSI-2 startup as specified in the
i.MX6
* reference manual is as follows:
*
* 1. Deassert presetn signal (global reset).
* It's not clear what this "global reset" signal is (maybe APB
* global reset), but in any case this step would be probably
* be carried out during driver load in csi2_probe().
*
* 2. Configure MIPI Camera Sensor to put all Tx lanes in LP-11 state.
* This must be carried out by the MIPI sensor's s_power(ON)
subdev
* op.
*
* 3. D-PHY initialization.
* 4. CSI2 Controller programming (Set N_LANES, deassert PHY_SHUTDOWNZ,
* deassert PHY_RSTZ, deassert CSI2_RESETN).
* 5. Read the PHY status register (PHY_STATE) to confirm that all
data and
* clock lanes of the D-PHY are in LP-11 state.
* 6. Configure the MIPI Camera Sensor to start transmitting a clock
on the
* D-PHY clock lane.
* 7. CSI2 Controller programming - Read the PHY status register
(PHY_STATE)
* to confirm that the D-PHY is receiving a clock on the D-PHY
clock lane.
*/
I read this as the hardware needing to see the LP-11 -> HS transition
after the DPHY reset has been released, and before the CSI2 RX
controller is programmed.
I think that's a fair assumption, and there's another paragraph at the
end of that comment above that adds more evidence to that:
...
* All steps 3 through 7 are carried out by csi2_s_stream(ON) here. Step
* 6 is accomplished by calling the source subdev's s_stream(ON) between
* steps 5 and 7.
*/
So the driver is expecting that the LP-11 state persists until step 6,
at which the LP-11 -> HS transition occurs when streaming is started
at the transmitter.
But if the transmitter only stays in LP-11 state for the minimum 100
usec after it is powered on, and then _automatically_ transitions to
HS, it's quite possible the LP-11 -> HS transition will happen long
before the DPHY is taken out of reset. That's because the
transmitter's s_power(ON) is called when the capture device is opened
(via v4l2_pipeline_pm_use()), but the steps above are carried out when
streaming starts, so userland would have to issue VIDIOC_STREAMON well
within the 100 usec expires after open()'ing the device, for the
receiver hardware to see the transition.
Perhaps that would be an argument for moving steps 1 - 5 into the
driver's s_power(ON) call, which would first call s_power(ON) to the
transmitter and then immediately go through steps 1 - 5. Steps 6,7
would then remain in s_stream(ON).
Well, after more testing on the i.MX6q SabreSD with the MIPI CSI-2
OV5640, this looks like an advisable thing to do. I will submit a patch.
Steve
