Describe the Texas Instruments DS90UB954-Q1, a 2-input video deserializer
with I2C Address Translator and remote GPIOs.
Signed-off-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
---
Changes RFCv1 -> RFCv2:
- add explicit aliases for the FPD-link RX ports (optional)
- add proper remote GPIO description
---
.../bindings/media/i2c/ti,ds90ub954-q1.txt | 194 ++++++++++++++++++
1 file changed, 194 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.txt
diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.txt b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.txt
new file mode 100644
index 000000000000..73ce21ecc3b6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.txt
@@ -0,0 +1,194 @@
+Texas Instruments DS90UB954-Q1 dual video deserializer
+======================================================
+
+The TI DS90UB954-Q1 is a MIPI CSI-2 video deserializer that forwards video
+streams from up to two FPD-Link 3 connections to a MIPI CSI-2 output. It
+also allows access to remote I2C and GPIO.
+
+Required properties:
+
+ - compatible: must be "ti,ds90ub954-q1"
+
+ - reg: main I2C slave address; optionally aliases for RX port registers
+ and remote serializers. The main address is mandatory and must be the
+ first, others are optional and fall back to defaults if not
+ specified. See "reg-names".
+
+ - reset-gpios: chip reset GPIO, active low (connected to PDB pin of the chip)
+ - i2c-alias-pool: list of I2C addresses that are known to be available on the
+ "local" (SoC-to-deser) I2C bus; they will be picked at
+ runtime and used as aliases to reach remove I2C chips
+ - gpio-controller
+ - #gpio-cells: must be 3: FPD-Link 3 RX port number, remote gpio number, flags
+
+Optional properties:
+
+ - reg-names: names of I2C address used to communicate with the chip, must
+ match the "reg" values; mandatory if there are 2 or more
+ addresses
+ - "main": the main I2C address, used to access shared registers
+ - "rxport0", "rxport1": I2C alias to access FPD-link RX port specific
+ registers; must not be used by other slaves on the same bus
+ - "ser0", "ser1": I2C alias to access the remote serializer connected
+ on each FPD-link RX port; must not be used by other slaves on the
+ same bus
+ - interrupts: interrupt pin from the chip
+
+Required subnodes:
+
+ - ports: A ports node with one port child node per device input and output
+ port, in accordance with the video interface bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt. The
+ port nodes are numbered as follows:
+
+ Port Description
+ ------------------------------------
+ 0 Input from FPD-Link 3 RX port 0
+ 1 Input from FPD-Link 3 RX port 1
+ 2 CSI-2 output
+
+ Each port must have a "remote-chip" subnode that defines the remote
+ chip (serializer) with at least a "compatible" property
+
+ - i2c-atr: contains one child per RX port, each describes the I2C bus on
+ the remote side
+
+ Required properties:
+ - #address-cells = <1>;
+ - #size-cells = <0>;
+
+ Subnodes: one per each FPD-link RX port, each having:
+
+ Required properties for "i2c-atr" child bus nodes:
+ - reg: The number of the port where the remove chip is connected
+ - #address-cells = <1>;
+ - #size-cells = <0>;
+
+ Optional properties for "i2c-atr" child bus nodes:
+ - Other properties specific to the remote hardware
+ - Child nodes conforming to i2c bus binding
+
+
+Device node example
+-------------------
+
+&i2c0 {
+ deser: deser@3d {
+ compatible = "ti,ds90ub954-q1";
+ reg-names = "main", "rxport0", "rxport1", "ser0", "ser1";
+ reg = <0x3d>, <0x40>, <0x41>, <0x44>, <0x45>;
+ clocks = <&clk_25M>;
+ interrupt-parent = <&gic>;
+ interrupts = <3 1 IRQ_TYPE_LEVEL_HIGH>;
+ reset-gpios = <&gpio_ctl 4 GPIO_ACTIVE_LOW>;
+
+ i2c-alias-pool = /bits/ 16 <0x4a 0x4b 0x4c 0x4d 0x4e 0x4f>;
+
+ gpio-controller;
+ #gpio-cells = <3>; /* rxport, remote gpio num, flags */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ ds90ub954_fpd3_in0: endpoint {
+ remote-endpoint = <&sensor_0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ ds90ub954_fpd3_in1: endpoint {
+ remote-endpoint = <&sensor_1_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ ds90ub954_mipi_out0: endpoint {
+ data-lanes = <1 2 3 4>;
+ /* Actually a REFCLK multiplier */
+ data-rate = <1600000000>;
+ remote-endpoint = <&csirx_0_in>;
+ };
+ };
+ };
+
+ i2c-atr {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ remote_i2c0: i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ remote_i2c1: i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+};
+
+&ds90ub954_fpd3_in0 {
+ remote-chip {
+ compatible = "ti,ds90ub953-q1";
+ gpio-functions = <DS90_GPIO_FUNC_OUTPUT_REMOTE
+ DS90_GPIO_FUNC_UNUSED
+ DS90_GPIO_FUNC_UNUSED
+ DS90_GPIO_FUNC_UNUSED>;
+ };
+};
+
+&ds90ub954_fpd3_in1 {
+ remote-chip {
+ compatible = "ti,ds90ub953-q1";
+ gpio-functions = <DS90_GPIO_FUNC_OUTPUT_REMOTE
+ DS90_GPIO_FUNC_UNUSED
+ DS90_GPIO_FUNC_UNUSED
+ DS90_GPIO_FUNC_UNUSED>;
+ };
+};
+
+&remote_i2c0 {
+ sensor_0@3c {
+ compatible = "sony,imx274";
+ reg = <0x3c>;
+
+ reset-gpios = <&deser 0 0 GPIO_ACTIVE_LOW>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ sensor_0_out: endpoint {
+ remote-endpoint = <&ds90ub954_fpd3_in0>;
+ };
+ };
+ };
+};
+
+&remote_i2c1 {
+ sensor_0@3c {
+ compatible = "sony,imx274";
+ reg = <0x3c>;
+
+ reset-gpios = <&deser 1 0 GPIO_ACTIVE_LOW>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ sensor_1_out: endpoint {
+ remote-endpoint = <&ds90ub954_fpd3_in1>;
+ };
+ };
+ };
+};
--
2.17.1
