RE: [PATCH v8 2/2] media: v4l: xilinx: Add Xilinx MIPI CSI-2 Rx Subsystem driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sakari,

> -----Original Message-----
> From: Sakari Ailus [mailto:sakari.ailus@xxxxxx]
> Sent: Tuesday, June 18, 2019 8:29 PM
> To: Vishal Sagar <vsagar@xxxxxxxxxx>
> Cc: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>; Vishal Sagar
> <vishal.sagar@xxxxxxxxxx>; Hyun Kwon <hyunk@xxxxxxxxxx>;
> laurent.pinchart@xxxxxxxxxxxxxxxx; mchehab@xxxxxxxxxx;
> robh+dt@xxxxxxxxxx; mark.rutland@xxxxxxx; Michal Simek
> <michals@xxxxxxxxxx>; linux-media@xxxxxxxxxxxxxxx;
> devicetree@xxxxxxxxxxxxxxx; hans.verkuil@xxxxxxxxx; linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; Dinesh Kumar
> <dineshk@xxxxxxxxxx>; Sandip Kothari <sandipk@xxxxxxxxxx>; Luca Ceresoli
> <luca@xxxxxxxxxxxxxxxx>; Jacopo Mondi <jacopo@xxxxxxxxxx>
> Subject: Re: [PATCH v8 2/2] media: v4l: xilinx: Add Xilinx MIPI CSI-2 Rx
> Subsystem driver
> 
> Hi Vishal,
> 
> On Fri, Jun 07, 2019 at 07:11:47AM +0000, Vishal Sagar wrote:
> ...
> > > > +/**
> > > > + * xcsi2rxss_s_ctrl - This is used to set the Xilinx MIPI CSI-2 V4L2 controls
> > > > + * @ctrl: V4L2 control to be set
> > > > + *
> > > > + * This function is used to set the V4L2 controls for the Xilinx MIPI
> > > > + * CSI-2 Rx Subsystem. It is used to set the active lanes in the system.
> > > > + * The event counters can be reset.
> > > > + *
> > > > + * Return: 0 on success, errors otherwise
> > > > + */
> > > > +static int xcsi2rxss_s_ctrl(struct v4l2_ctrl *ctrl)
> > > > +{
> > > > +     struct xcsi2rxss_state *xcsi2rxss =
> > > > +             container_of(ctrl->handler, struct xcsi2rxss_state,
> > > > +                          ctrl_handler);
> > > > +     struct xcsi2rxss_core *core = &xcsi2rxss->core;
> > > > +     int ret = 0;
> > > > +
> > > > +     mutex_lock(&xcsi2rxss->lock);
> > > > +
> > > > +     switch (ctrl->id) {
> > > > +     case V4L2_CID_XILINX_MIPICSISS_ACT_LANES:
> > > > +             /*
> > > > +              * This will be called only when "Enable Active Lanes" parameter
> > > > +              * is set in design
> > > > +              */
> > >
> > > You generally get the number of lanes from firmware. There's no need to
> add
> > > a control for it.
> > >
> >
> > I don't understand what firmware means here. There is no other code
> running.
> > I don't see how to modify the number of lanes apart from using v4l control.
> 
> It's not the user that provides this information. Again, if you want this
> feature right from the time the driver is merged to mainline, then rebase
> the set on top of Jacopo's frame descriptor set. But it may take a while.
> 

Thanks for reviewing again and sharing this. 
Since Jacopo's frame descriptor set will take a while, I will remove this control for now from the driver so that the driver can get into upstream.

Regards
Vishal Sagar

> >
> > > > +             if (core->enable_active_lanes) {
> > > > +                     u32 active_lanes;
> > > > +
> > > > +                     xcsi2rxss_clr_and_set(core, XCSI_PCR_OFFSET,
> > > > +                                           XCSI_PCR_ACTLANES_MASK,
> > > > +                                           ctrl->val - 1);
> > > > +                     /*
> > > > +                      * This delay is to allow the value to reflect as write
> > > > +                      * and read paths are different.
> > > > +                      */
> > > > +                     udelay(1);
> > > > +                     active_lanes = xcsi2rxss_read(core, XCSI_PCR_OFFSET);
> > > > +                     active_lanes &= XCSI_PCR_ACTLANES_MASK;
> > > > +                     active_lanes++;
> > > > +                     if (active_lanes != ctrl->val)
> > > > +                             dev_info(core->dev, "RxByteClkHS absent\n");
> > > > +                     dev_dbg(core->dev, "active lanes = %d\n", ctrl->val);
> > > > +             } else {
> > > > +                     ret = -EINVAL;
> > > > +             }
> > > > +             break;
> > > > +     case V4L2_CID_XILINX_MIPICSISS_RESET_COUNTERS:
> > > > +             xcsi2rxss_reset_event_counters(xcsi2rxss);
> > > > +             break;
> > > > +     default:
> > > > +             ret = -EINVAL;
> > > > +             break;
> > > > +     }
> > > > +
> > > > +     mutex_unlock(&xcsi2rxss->lock);
> > > > +
> > > > +     return ret;
> > > > +}
> 
> --
> Regards,
> 
> Sakari Ailus




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux