RE: [v4 1/6] dt-bindings: media: Document bindings for DW MIPI CSI-2 Host

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sakari,

Thank you for your feedback.
I have my comments inline.

From: Sakari Ailus <sakari.ailus@xxxxxx>
Date: Fri, Jun 28, 2019 at 15:13:26

> Hi Luis,
> 
> Thank you for the patchset.
> 
> On Tue, Jun 11, 2019 at 09:20:50PM +0200, Luis Oliveira wrote:
> > From: Luis Oliveira <lolivei@xxxxxxxxxxxx>
> > 
> > Add bindings for Synopsys DesignWare MIPI CSI-2 host.
> > 
> > Signed-off-by: Luis Oliveira <lolivei@xxxxxxxxxxxx>
> > ---
> > Changelog
> > v3-v4
> > - remove "plat" from the block name @rob @laurent
> > - remove "phy-names" when single-entry @rob
> > - remove "snps,output-type" -> went to the driver config @laurent
> > 
> >  .../devicetree/bindings/media/snps,dw-csi.txt      | 41 ++++++++++++++++++++++
> >  1 file changed, 41 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/media/snps,dw-csi.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/media/snps,dw-csi.txt b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
> > new file mode 100644
> > index 0000000..613b7f9
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/snps,dw-csi.txt
> > @@ -0,0 +1,41 @@
> > +Synopsys DesignWare CSI-2 Host controller
> > +
> > +Description
> > +-----------
> > +
> > +This HW block is used to receive image coming from an MIPI CSI-2 compatible
> > +camera.
> > +
> > +Required properties:
> > +- compatible		: shall be "snps,dw-csi"
> > +- reg			: physical base address and size of the device memory
> > +			  mapped registers;
> > +- interrupts		: DW CSI-2 Host interrupts
> > +- phys			: List of one PHY specifier (as defined in
> > +			  Documentation/devicetree/bindings/phy/phy-bindings.txt).
> > +			  This PHY is a MIPI DPHY working in RX mode.
> > +- resets		: Reference to a reset controller (optional)
> > +
> > +The per-board settings:
> > + - port sub-node describing a single endpoint connected to the camera as
> > +   described in video-interfaces.txt[1].
> 
> Which endpoint properties in video-interfaces.txt are relevant for the
> hardware? Which values may they have?
> 

Currently I'm using only two properties "data-lanes" and "bus-width", but 
I have plans to add blanking info also.
I will add more info.

> > +
> > +Example:
> > +
> > +	csi2: csi2@3000 {
> > +		compatible = "snps,dw-csi";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		reg = < 0x03000 0x7FF>;
> 
> reg = <0x03000 0x7FF>;

Yes, I've missed that.

> 
> > +		phys = <&mipi_dphy_rx>;
> > +		resets = <&dw_rst 1>;
> > +		interrupts = <2>;
> > +
> > +		port@0 {
> > +			reg = <0>;
> 
> You can drop "@0" and the reg property.

Ok thank you.
> 
> > +			csi_ep1: endpoint {
> > +				remote-endpoint = <&camera_1>;
> > +				data-lanes = <1 2>;
> > +			};
> > +		};
> > +	};
> 
> -- 
> Kind regards,
> 
> Sakari Ailus

Best regards,
Luis





[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux