[PATCH] media: i2c: ov5645: Fix power up sequence

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This is mostly a port of Jacopo's fix:

  commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
  Author: Jacopo Mondi <jacopo@xxxxxxxxxx>
  Date:   Fri Jul 6 05:51:52 2018 -0400

  media: ov5640: Re-work MIPI startup sequence

In the OV5645 case, the changes are:

- Move OV5645_IO_MIPI_CTRL00 (0x300e) out of the initial setting blob.
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
  LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current
  power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.

With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.

Many thanks to Fabio Estevam for his help debugging this issue.

Signed-off-by: Ezequiel Garcia <ezequiel@xxxxxxxxxxxxx>
---
 drivers/media/i2c/ov5645.c | 34 +++++++++++++++++++++++++++++++---
 1 file changed, 31 insertions(+), 3 deletions(-)

diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c
index 124c8df04633..05430a81c977 100644
--- a/drivers/media/i2c/ov5645.c
+++ b/drivers/media/i2c/ov5645.c
@@ -45,6 +45,8 @@
 #define		OV5645_CHIP_ID_HIGH_BYTE	0x56
 #define OV5645_CHIP_ID_LOW		0x300b
 #define		OV5645_CHIP_ID_LOW_BYTE		0x45
+#define OV5645_IO_MIPI_CTRL00		0x300e
+#define OV5645_PAD_OUTPUT00		0x3019
 #define OV5645_AWB_MANUAL_CONTROL	0x3406
 #define		OV5645_AWB_MANUAL_ENABLE	BIT(0)
 #define OV5645_AEC_PK_MANUAL		0x3503
@@ -55,6 +57,7 @@
 #define		OV5645_ISP_VFLIP		BIT(2)
 #define OV5645_TIMING_TC_REG21		0x3821
 #define		OV5645_SENSOR_MIRROR		BIT(1)
+#define OV5645_MIPI_CTRL00		0x4800
 #define OV5645_PRE_ISP_TEST_SETTING_1	0x503d
 #define		OV5645_TEST_PATTERN_MASK	0x3
 #define		OV5645_SET_TEST_PATTERN(x)	((x) & OV5645_TEST_PATTERN_MASK)
@@ -121,7 +124,6 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3503, 0x07 },
 	{ 0x3002, 0x1c },
 	{ 0x3006, 0xc3 },
-	{ 0x300e, 0x45 },
 	{ 0x3017, 0x00 },
 	{ 0x3018, 0x00 },
 	{ 0x302e, 0x0b },
@@ -737,13 +739,30 @@ static int ov5645_s_power(struct v4l2_subdev *sd, int on)
 				goto exit;
 			}
 
-			ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
-					       OV5645_SYSTEM_CTRL0_STOP);
+			ret = ov5645_write_reg(ov5645,
+					       OV5645_IO_MIPI_CTRL00, 0x40);
 			if (ret < 0) {
 				ov5645_set_power_off(ov5645);
 				goto exit;
 			}
+
+			ret = ov5645_write_reg(ov5645,
+					       OV5645_MIPI_CTRL00, 0x24);
+			if (ret < 0) {
+				ov5645_set_power_off(ov5645);
+				goto exit;
+			}
+
+			ret = ov5645_write_reg(ov5645,
+					       OV5645_PAD_OUTPUT00, 0x70);
+			if (ret < 0) {
+				ov5645_set_power_off(ov5645);
+				goto exit;
+			}
+
+			usleep_range(500, 1000);
 		} else {
+			ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58);
 			ov5645_set_power_off(ov5645);
 		}
 	}
@@ -1049,11 +1068,20 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable)
 			dev_err(ov5645->dev, "could not sync v4l2 controls\n");
 			return ret;
 		}
+
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_START);
 		if (ret < 0)
 			return ret;
 	} else {
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_STOP);
 		if (ret < 0)
-- 
2.20.1




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux