On Fri, May 24, 2019 at 07:31:03AM +0200, Frédéric Deghetto wrote: > Probably related to this issue; ir-keytable -a /etc/rc_maps.conf -v gives: > > /sys/class/rc/rc0/protocols protocol rc-5 (disabled) > /sys/class/rc/rc0/protocols protocol nec (disabled) > /sys/class/rc/rc0/protocols protocol rc-6 (enabled) > /sys/class/rc/rc0/protocols protocol jvc (disabled) > /sys/class/rc/rc0/protocols protocol sony (disabled) > /sys/class/rc/rc0/protocols protocol rc-5-sz (disabled) > /sys/class/rc/rc0/protocols protocol sanyo (disabled) > /sys/class/rc/rc0/protocols protocol sharp (disabled) > /sys/class/rc/rc0/protocols protocol mce_kbd (disabled) > /sys/class/rc/rc0/protocols protocol xmp (disabled) > /sys/class/rc/rc0/protocols protocol imon (disabled) > /sys/class/rc/rc0/protocols protocol lirc (enabled) > Table for gpio_ir_recv, rc-rc6-mce not found. Keep as-is > > like if rc-rc6-mce was not available anymore ? This looks like ir-keytable could not match up your /etc/rc_maps.conf with your rc device. Please can you provide: 1) output of "ir-keytable" no (arguments) 2) output of "cat /etc/rc_maps.conf" 3) output of "ir-keytable --version" > > Have a good day, > > Frederic > > > Le 24/05/2019 à 06:12, Frédéric Deghetto a écrit : > > Good day, > > > > Information on the system: > > > > - Raspberry 3b+ > > > > - Updated yesterday to 4.19.42-v7+ > > > > > > Before the update the remote control was working well with: > > > > - gpio-rc-recv rc-rc6-mce kodi (into the file rc_maps.cfg) > > > > - And the following data into /etc/rc_keymaps/kodi: > > > > # table kodi, type: NEC > > 0x140 KEY_POWER > > 0x1ff KEY_TAB > > 0x143 KEY_RED > > 0x10f KEY_GREEN > > 0x110 KEY_MINUS > > 0x118 KEY_VOLUMEUP > > 0x111 KEY_ESC > > 0x119 KEY_BACKSPACE > > 0x116 KEY_UP > > 0x151 KEY_LEFT > > 0x113 KEY_ENTER > > 0x150 KEY_RIGHT > > 0x11a KEY_DOWN > > 0x14c KEY_EPG > > 0x100 KEY_C > > 0x14e KEY_1 > > 0x10d KEY_2 > > 0x10c KEY_3 > > 0x14a KEY_4 > > 0x109 KEY_5 > > 0x108 KEY_6 > > 0x146 KEY_7 > > 0x105 KEY_8 > > 0x104 KEY_9 > > 0x141 KEY_F8 > > 0x101 KEY_0 > > 0x142 KEY_DELETE > > > > > > Since the kernel update I get this message from dmesg: "rc rc0: two > > consecutive events of type space", and the remote control doesn't work. This is a warning message about the driver and should not affect functionality, > > I tried to force the protocol NEC with ir-keytable -t -p NEC and I can > > this some events. Something strange, when I push a button I can get the > > event of the previous pushed button. By insisting I get the right one. That's very odd. This sounds like a problem with trailing spaces/timeouts, which should work fine in v4.19. What distribtion are you using and what version? Thanks Sean > > > > I went to google and didn't see any workaround. > > > > Many thanks for your support, > > > > Frederic > >
