Hi Louis, Thanks for the update! I added one inline comment below. Best regards, Keiichi On Tue, Mar 12, 2019 at 5:49 PM Louis Kuo <louis.kuo@xxxxxxxxxxxx> wrote: > > Hi Keiichi, > Thanks for your advice. > I have fixed code following your comments. > > Please help me to review my notes below your comments, I will wait your > reply and send new patch again. > > BRs > Louis > > > > On Fri, 2019-03-08 at 18:59 +0900, Keiichi Watanabe wrote: > > Hi, thank you Louis for the patch! > > And, thank you Tomasz for adding me to CC in this thread:) > > > > Let me add only general comments because I don't have enough knowledge > > about the technical details of this device. > > Please see my comments inline. > > > > > > On Tue, Mar 5, 2019 at 4:51 PM Tomasz Figa <tfiga@xxxxxxxxxxxx> wrote: > > > > > > +CC Shik and Keiichi > > > > > > On Thu, Feb 21, 2019 at 4:22 PM Louis Kuo <louis.kuo@xxxxxxxxxxxx> wrote: > > > > > > > > This patch adds Mediatek's sensor interface driver. Sensor interface driver > > > > is a MIPI-CSI2 host driver, namely, a HW camera interface controller. > > > > It support a widely adopted, simple, high-speed protocol primarily intended > > > > for point-to-point image and video transmission between cameras and host > > > > devices. > > > > > > > > The mtk-isp directory will contain drivers for multiple IP blocks found in > > > > Mediatek ISP system. It will include ISP Pass 1 driver, sensor interface > > > > driver, DIP driver and face detection driver. > > > > > > > > Signed-off-by: Louis Kuo <louis.kuo@xxxxxxxxxxxx> > > > > --- > > > > drivers/media/platform/Makefile | 2 + > > > > drivers/media/platform/mtk-isp/Makefile | 14 + > > > > drivers/media/platform/mtk-isp/isp_50/Makefile | 17 + > > > > .../media/platform/mtk-isp/isp_50/seninf/Makefile | 4 + > > > > .../platform/mtk-isp/isp_50/seninf/mtk_seninf.c | 1339 ++++++++++++++++++++ > > > > .../mtk-isp/isp_50/seninf/seninf_drv_def.h | 201 +++ > > > > .../platform/mtk-isp/isp_50/seninf/seninf_reg.h | 992 +++++++++++++++ > > > > 7 files changed, 2569 insertions(+) > > > > create mode 100644 drivers/media/platform/mtk-isp/Makefile > > > > create mode 100644 drivers/media/platform/mtk-isp/isp_50/Makefile > > > > create mode 100644 drivers/media/platform/mtk-isp/isp_50/seninf/Makefile > > > > create mode 100644 drivers/media/platform/mtk-isp/isp_50/seninf/mtk_seninf.c > > > > create mode 100644 drivers/media/platform/mtk-isp/isp_50/seninf/seninf_drv_def.h > > > > create mode 100644 drivers/media/platform/mtk-isp/isp_50/seninf/seninf_reg.h > > > > > > > > diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile > > > > index e6deb25..9fef94f 100644 > > > > --- a/drivers/media/platform/Makefile > > > > +++ b/drivers/media/platform/Makefile > > > > @@ -75,6 +75,8 @@ obj-$(CONFIG_VIDEO_ROCKCHIP_RGA) += rockchip/rga/ > > > > > > > > obj-y += omap/ > > > > > > > > +obj-y += mtk-isp/ > > > > + > > > > obj-$(CONFIG_VIDEO_AM437X_VPFE) += am437x/ > > > > > > > > obj-$(CONFIG_VIDEO_XILINX) += xilinx/ > > > > diff --git a/drivers/media/platform/mtk-isp/Makefile b/drivers/media/platform/mtk-isp/Makefile > > > > new file mode 100644 > > > > index 0000000..9d245f0 > > > > --- /dev/null > > > > +++ b/drivers/media/platform/mtk-isp/Makefile > > > > @@ -0,0 +1,14 @@ > > > > +# > > > > +# Copyright (C) 2018 MediaTek Inc. > > > > +# > > > > +# This program is free software: you can redistribute it and/or modify > > > > +# it under the terms of the GNU General Public License version 2 as > > > > +# published by the Free Software Foundation. > > > > +# > > > > +# This program is distributed in the hope that it will be useful, > > > > +# but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > > +# GNU General Public License for more details. > > > > +# > > > > + > > > > +obj-y += isp_50/ > > > > \ No newline at end of file > > > > diff --git a/drivers/media/platform/mtk-isp/isp_50/Makefile b/drivers/media/platform/mtk-isp/isp_50/Makefile > > > > new file mode 100644 > > > > index 0000000..bd8cd19 > > > > --- /dev/null > > > > +++ b/drivers/media/platform/mtk-isp/isp_50/Makefile > > > > @@ -0,0 +1,17 @@ > > > > +# > > > > +# Copyright (C) 2018 MediaTek Inc. > > > > +# > > > > +# This program is free software: you can redistribute it and/or modify > > > > +# it under the terms of the GNU General Public License version 2 as > > > > +# published by the Free Software Foundation. > > > > +# > > > > +# This program is distributed in the hope that it will be useful, > > > > +# but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > > +# GNU General Public License for more details. > > > > +# > > > > + > > > > +ifeq ($(CONFIG_MTK_SENINF),y) > > > > +obj-y += seninf/ > > > > +endif > > > > + > > > > diff --git a/drivers/media/platform/mtk-isp/isp_50/seninf/Makefile b/drivers/media/platform/mtk-isp/isp_50/seninf/Makefile > > > > new file mode 100644 > > > > index 0000000..f1b2e2d > > > > --- /dev/null > > > > +++ b/drivers/media/platform/mtk-isp/isp_50/seninf/Makefile > > > > @@ -0,0 +1,4 @@ > > > > +MODULE = mtk_seninf > > > > +LIB_FILES = mtk_seninf > > > > + > > > > +obj-$(CONFIG_MTK_SENINF) += mtk_seninf.o > > > > diff --git a/drivers/media/platform/mtk-isp/isp_50/seninf/mtk_seninf.c b/drivers/media/platform/mtk-isp/isp_50/seninf/mtk_seninf.c > > > > new file mode 100644 > > > > index 0000000..7ac8a4a > > > > --- /dev/null > > > > +++ b/drivers/media/platform/mtk-isp/isp_50/seninf/mtk_seninf.c > > > > @@ -0,0 +1,1339 @@ > > > > +// SPDX-License-Identifier: GPL-2.0 > > > > +/* > > > > + * Copyright (C) 2016 MediaTek Inc. > > > > + * > > > > + * This program is free software; you can redistribute it and/or modify > > > > + * it under the terms of the GNU General Public License version 2 as > > > > + * published by the Free Software Foundation. > > > > + * > > > > + * This program is distributed in the hope that it will be useful, > > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. > > > > + * See http://www.gnu.org/licenses/gpl-2.0.html for more details. > > > > + */ > > > > + > > > > +#include <linux/types.h> > > > > +#include <linux/delay.h> > > > > +#include <linux/err.h> > > > > +#include <linux/io.h> > > > > +#include <linux/platform_device.h> > > > > +#include <linux/slab.h> > > > > +#include <linux/module.h> > > > > +#include <linux/init.h> > > > > +#include <linux/pm_runtime.h> > > > > +#include <linux/clk.h> > > > > +#include <linux/interrupt.h> > > > > +#include <linux/of_platform.h> > > > > +#include <linux/of.h> > > > > +#include <linux/of_graph.h> > > > > +#include <linux/of_irq.h> > > > > +#include <linux/of_address.h> > > > > +#include <linux/vmalloc.h> > > > > +#ifdef CONFIG_COMPAT > > > > +#include <linux/compat.h> > > > > +#endif > > > > +#include <linux/videodev2.h> > > > > +#include <media/v4l2-common.h> > > > > +#include <media/v4l2-dev.h> > > > > +#include <media/v4l2-device.h> > > > > +#include <media/v4l2-subdev.h> > > > > +#include <media/v4l2-fwnode.h> > > > > +#include <media/v4l2-ctrls.h> > > > > +#include <media/v4l2-async.h> > > > > +#include <media/media-entity.h> > > > > +#include "seninf_reg.h" > > > > +#include "seninf_drv_def.h" > > > > + > > > > +#define IS_4D1C (csi_info->port < CFG_CSI_PORT_0A) > > > > +#define IS_CDPHY_COMBO (csi_info->port == CFG_CSI_PORT_0A ||\ > > > > + csi_info->port == CFG_CSI_PORT_0B ||\ > > > > + csi_info->port == CFG_CSI_PORT_0) > > > > + > > > > +static struct seninf_csi_info SENINF_CSI_INFO[CFG_CSI_PORT_MAX_NUM] = { > > > > + {CFG_CSI_PORT_0, SENINF_1}, > > > > + {CFG_CSI_PORT_1, SENINF_3}, > > > > + {CFG_CSI_PORT_2, SENINF_5}, > > > > + {CFG_CSI_PORT_0A, SENINF_1}, > > > > + {CFG_CSI_PORT_0B, SENINF_2}, > > > > +}; > > > > + > > > > +static struct sensor_vc_info_struct SENSOR_VC_INFO[2] = { > > > > + /* Preview mode setting */ > > > > + { > > > > + 0x02, 0x0A, 0x00, 0x08, 0x40, 0x00, > > > > + 0x00, 0x2B, 0x0500, 0x02D0, 0x00, 0x00, 0x0000, 0x0000, > > > > + 0x00, 0x00, 0x0000, 0x0000, 0x00, 0x00, 0x0000, 0x0000 > > > > + }, > > > > + /* Capture mode setting */ > > > > + { > > > > + 0x02, 0x0A, 0x00, 0x08, 0x40, 0x00, > > > > + 0x00, 0x2B, 0x1080, 0x0C40, 0x00, 0x00, 0x0000, 0x0000, > > > > + 0x01, 0x2B, 0x0100, 0x0300, 0x00, 0x00, 0x0000, 0x0000 > > > > + } > > > > +}; > > > > + > > > > +struct _seninf { > > > > + struct v4l2_subdev subdev; > > > > + struct device *dev; > > > > + struct v4l2_fwnode_endpoint ep[2]; > > > > + struct v4l2_ctrl_handler ctrl_handler; > > > > + struct v4l2_ctrl *test_pattern; > > > > + struct media_pad pads[NUM_PADS]; > > > > + struct clk *cam_clk, *top_mux_clk; > > > > + unsigned int port; > > > > + int format; > > > > + int dpcm; > > > > + int mux_select; > > > > + void __iomem *base_reg; > > > > + void __iomem *rx_reg; > > > > + unsigned char *seninf_hw; > > > > + unsigned char *seninf_ctrl[SENINF_NUM]; > > > > + unsigned char *seninf_mux[SENINF_MUX_NUM]; > > > > + unsigned char *csi2_rx[CFG_CSI_PORT_MAX_NUM]; > > > > + unsigned char *csi_rx_conf[SENINF_NUM]; > > > > +}; > > > > + > > > > +static int set_top_mux_ctrl(struct _seninf *priv, > > > > + unsigned int mux_idx, unsigned int seninf_src > > > > +) > > > > +{ > > > > + int ret = 0; > > > > Since |ret| is always 0, you don't need to define |ret|. You can > > simply write "return 0" instead. > Got it and fixed. > > > > > > + void *pseninf = priv->seninf_hw; > > > > + > > > > + seninf_write_reg(pseninf, SENINF_TOP_MUX_CTRL, > > > > + ((seninf_read_reg(pseninf, SENINF_TOP_MUX_CTRL) & > > > > + (~(0xF << (mux_idx * 4)))) | ((seninf_src & 0xF) > > > > + << (mux_idx * 4)))); > > > > + return ret; > > > > +} > > > > + > > > > +static int __attribute__((unused)) > > > > + set_tg_mux_ctrl(struct _seninf *priv, > > > > + unsigned int target_tg, unsigned int mux_src > > > > +) > > > > +{ > > > > + int ret = 0; > > > > ditto. > > > > > > + void *pseninf = priv->seninf_hw; > > > > + > > > > + seninf_write_reg(pseninf, SENINF_TOP_CAM_MUX_CTRL, > > > > + ((seninf_read_reg(pseninf, > > > > + SENINF_TOP_CAM_MUX_CTRL) & > > > > + (~(0xF << (target_tg * 4)))) | ((mux_src & 0xF) > > > > + << (target_tg * 4)))); > > > > + return ret; > > > > +} > > > > + > > > > +static int set_virtual_channel(struct _seninf *priv, unsigned int seninf_sel, > > > > + unsigned int vc0_id, unsigned int vc1_id, > > > > + unsigned int vc2_id, unsigned int vc3_id, > > > > + unsigned int vc4_id, unsigned int vc5_id) > > > > +{ > > > > + int ret = 0; > > > > ditto. > > > > > > + void *pseninf = NULL; > > > > Could you initialize pseninf with priv->seninf_ctrl[seninf_sel] here? > Got it and fixed. > > > > > > + > > > > + return 0; /* todo: support virtual channel */ > > > > Hmm, can we remove this todo now? > > Or, are the following part still work in progress? > Yes, this function is prepared for virtual channel case. > I remove this line and add a define "SUPPORT_VIRTUAL_CHANNEL" to enclose > this function for future advanced application. Is supporting virtual channel a separated work? Then, how about removing this function from this patch and creating a new patch later for virtual channel support? > > > > > > + > > > > + pseninf = priv->seninf_ctrl[seninf_sel]; > > > > + > > > > + /* General Long Packet Data Types: 0x10-0x17 */ > > > > + if ((0x10 <= (vc0_id >> 2) && (vc0_id >> 2) <= 0x17) || > > > > + (0x10 <= (vc1_id >> 2) && (vc1_id >> 2) <= 0x17) || > > > > + (0x10 <= (vc2_id >> 2) && (vc2_id >> 2) <= 0x17) || > > > > + (0x10 <= (vc3_id >> 2) && (vc3_id >> 2) <= 0x17) || > > > > + (0x10 <= (vc4_id >> 2) && (vc4_id >> 2) <= 0x17) || > > > > + (0x10 <= (vc5_id >> 2) && (vc5_id >> 2) <= 0x17)) > > > > + write_master(pseninf, SENINF1_CSI2_CTL, > > > > + (1 << 12), 0x00001000); > > > > + > > > > + pr_debug("VC Data set :0x%x 0x%x\n", ((vc3_id) << 24) | ((vc2_id) << 16) > > > > + | ((vc1_id) << 8) | (vc0_id), (vc5_id << 8) | (vc4_id)); > > > > + > > > > + /* 0x1a04_0a3c for VC0~VC3 */ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_DI, ((vc3_id) << 24) | > > > > + ((vc2_id) << 16) | ((vc1_id) << 8) | (vc0_id)); > > > > + /* 0x1a04_0af0 for VC4~VC5 */ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_DI_EXT, > > > > + (vc5_id << 8) | (vc4_id)); > > > > + /* Clear */ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_DI_CTRL, 0x00); > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_DI_CTRL_EXT, 0x00); > > > > + if (vc0_id == 0 && vc1_id == 0 && vc2_id == 0 && > > > > + vc3_id == 0 && vc4_id == 0 && vc5_id == 0) > > > > + return ret; > > > > + > > > > + if ((vc0_id & 0xfc) != 0) > > > > + write_master(pseninf, SENINF1_CSI2_DI_CTRL, > > > > + ((1 << 0) | (1 << 1)), 0x00000007); > > > > + if ((vc1_id & 0xfc) != 0) > > > > + write_master(pseninf, SENINF1_CSI2_DI_CTRL, > > > > + ((1 << 8) | (1 << 9)), 0x00000700); > > > > + if ((vc2_id & 0xfc) != 0) > > > > + write_master(pseninf, SENINF1_CSI2_DI_CTRL, > > > > + ((1 << 16) | (1 << 17)), 0x00070000); > > > > + if ((vc3_id & 0xfc) != 0) > > > > + write_master(pseninf, SENINF1_CSI2_DI_CTRL, > > > > + ((1 << 24) | (1 << 25)), 0x07000000); > > > > + if ((vc4_id & 0xfc) != 0) > > > > + write_master(pseninf, SENINF1_CSI2_DI_CTRL_EXT, > > > > + ((1 << 0) | (1 << 1)), 0x00000007); > > > > + if ((vc5_id & 0xfc) != 0) > > > > + write_master(pseninf, SENINF1_CSI2_DI_CTRL_EXT, > > > > + ((1 << 8) | (1 << 9)), 0x00000700); > > > > + > > > > + pr_debug("VC Data(0x%x,0x%x), VC Ctrl(0x%x,0x%x)", > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_DI), > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_DI_EXT), > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_DI_CTRL), > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_DI_CTRL_EXT)); > > > > + return ret; > > > > +} > > > > + > > > > +static int set_mux_ctrl(struct _seninf *priv, > > > > + unsigned int mux, unsigned int hs_pol, > > > > + unsigned int vs_pol, unsigned int src_type_sel, > > > > + unsigned int input_data_type, unsigned int pixel_mode > > > > +) > > > > +{ > > > > + int ret = 0; > > > > ditto. > > > > > > + void *pseninf = priv->seninf_mux[mux]; > > > > + > > > > + unsigned int temp = 0; > > > > + > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + (src_type_sel << 12), 0x0000F000); > > > > + temp = (src_type_sel == TEST_MODEL) ? 0 : 1; > > > > + write_master(pseninf, SENINF1_MUX_CTRL_EXT, > > > > + (temp << 0), 0x00000003); > > > > + if (pixel_mode == 1) { /*2 Pixel*/ > > > > + write_master(pseninf, SENINF1_MUX_CTRL_EXT, > > > > + (0 << 4), 0x00000010); > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + (1 << 8), 0x00000100); > > > > + > > > > + } else if (pixel_mode == 2) { /* 4 Pixel*/ > > > > + write_master(pseninf, SENINF1_MUX_CTRL_EXT, > > > > + (1 << 4), 0x00000010); > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + (0 << 8), 0x00000100); > > > > + } else { /* 1 pixel*/ > > > > + write_master(pseninf, SENINF1_MUX_CTRL_EXT, > > > > + (0 << 4), 0x00000010); > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + (0 << 8), 0x00000100); > > > > + } > > > > Could you use switch-statement here for readability? > > Probably, like this? > Got it and fixed. > > > > unsigned int temp1, temp2; > > ... > > switch(pixel_mode) { > > case 1: /* 2 Pixel */ > > temp1 = 0 << 4; > > temp2 = 1 << 8; > > break; > > case 2: /* 4 Pixel */ > > temp1 = 1 << 4; > > temp2 = 0 << 8; > > break; > > default: /* 1 Pixel */ > > temp1 = 0 << 4; > > temp2 = 0 << 8; > > } > > write_master(pseninf, SENINF1_MUX_CTRL_EXT, temp1, 0x00000010); > > write_master(pseninf, SENINF1_MUX_CTRL, temp2, 0x00000100); > > > > > > + > > > > + if (input_data_type != JPEG_FMT) > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + (2 << 28), 0x30000000); > > > > + else > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + (0 << 28), 0x30000000); > > > > + > > > > + if (src_type_sel == CSI2 || src_type_sel >= MIPI_SENSOR) { > > > > + /*Need to use Default for New design*/ > > > > nit: Please add a spaces after '/*' and before '*/'. > > same for all other one-line comments below. > Got it and fixed all. > > > > > > + if (input_data_type != JPEG_FMT) > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + ((0x1B << 22) | (0x1F << 16)), > > > > + 0x0FFF0000); > > > > + else > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + ((0x18 << 22) | (0x1E << 16)), > > > > + 0x0FFF0000); > > > > + } > > > > + > > > > + write_master(pseninf, SENINF1_MUX_CTRL, > > > > + ((hs_pol << 10) | (vs_pol << 9)), 0x00000600); > > > > + > > > > + temp = seninf_read_reg(pseninf, SENINF1_MUX_CTRL); > > > > + seninf_write_reg(pseninf, SENINF1_MUX_CTRL, temp | 0x3); > > > > + seninf_write_reg(pseninf, SENINF1_MUX_CTRL, temp & 0xFFFFFFFC); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int enable_mux(struct _seninf *priv, unsigned int mux) > > > > +{ > > > > + void *pseninf = priv->seninf_mux[mux]; > > > > + > > > > + write_master(pseninf, SENINF1_MUX_CTRL, (1 << 31), 0x80000000); > > > > + return 0; > > > > +} > > > > + > > > > +static struct seninf_csi_info *get_csi_info(struct _seninf *priv, > > > > + unsigned int mipi_port) > > > > +{ > > > > + int i; > > > > + > > > > + for (i = 0; i < CFG_CSI_PORT_MAX_NUM; i++) { > > > > + if (SENINF_CSI_INFO[i].port == mipi_port) > > > > + return &SENINF_CSI_INFO[i]; > > > > + } > > > > + > > > > + return NULL; > > > > +} > > > > + > > > > +static int set_csi_mipi(struct _seninf *priv, > > > > + struct seninf_csi_mipi *pcsi_mipi) > > > > +{ > > > > + int ret = 0; > > > > ditto. > > > > > > + void *pseninf = NULL; > > > > + void *seninf_base = priv->seninf_hw; > > > > + void *pmipi_rx = NULL; > > > > + void *pmipi_rx_base = priv->csi2_rx[CFG_CSI_PORT_0]; > > > > + void *pmipi_rx_conf = NULL; > > > > Could you initialize |pmipi_rx|, |pseninf|, and |pmipi_rx_conf| here > > instead of the below? > Got it and fixed. > > > > > > + struct seninf_csi_info *csi_info = pcsi_mipi->csi_info; > > > > + unsigned int cal_sel; > > > > + unsigned int temp = 0; > > > > + > > > > + pr_debug("IS_4D1C %d csi_type %d port %d enable %d\n", > > > > + IS_4D1C, pcsi_mipi->csi_type, csi_info->port, > > > > + pcsi_mipi->enable); > > > > + > > > > + pmipi_rx = priv->csi2_rx[csi_info->port]; > > > > + pseninf = priv->seninf_ctrl[csi_info->seninf]; > > > > + pmipi_rx_conf = priv->csi_rx_conf[csi_info->seninf]; > > > > + > > > > + if (csi_info->port == CFG_CSI_PORT_1) { > > > > + write_master(seninf_base, SENINF_TOP_PHY_SENINF_CTL_CSI1, > > > > + ((0 << 0) | (2 << 8) | > > > > + (pcsi_mipi->enable << 31)), 0x80000701); > > > > + cal_sel = 1; > > > > + } else if (csi_info->port == CFG_CSI_PORT_2) { > > > > + write_master(seninf_base, SENINF_TOP_PHY_SENINF_CTL_CSI2, > > > > + ((0 << 0) | (2 << 8) | > > > > + (pcsi_mipi->enable << 31)), 0x80000701); > > > > + cal_sel = 2; > > > > + } else if (csi_info->port == CFG_CSI_PORT_0) { > > > > + cal_sel = 0; > > > > + write_master(seninf_base, SENINF_TOP_PHY_SENINF_CTL_CSI0, > > > > + ((0 << 0) | (2 << 8) | > > > > + (pcsi_mipi->enable << 31)), 0x80000701); > > > > + } else if (csi_info->port == CFG_CSI_PORT_0A) { > > > > + cal_sel = 0; > > > > + write_master(seninf_base, SENINF_TOP_PHY_SENINF_CTL_CSI0, > > > > + ((0 << 1) | (1 << 8) | (1 << 12) | > > > > + (pcsi_mipi->enable << 31)), 0x80003701); > > > > + } else if (csi_info->port == CFG_CSI_PORT_0B) { > > > > + cal_sel = 0; > > > > + write_master(seninf_base, SENINF_TOP_PHY_SENINF_CTL_CSI0, > > > > + ((0 << 1) | (1 << 8) | (1 << 12) | > > > > + (pcsi_mipi->enable << 31)), 0x80003701); > > > > + } else { > > > > + pr_err("unsupported CSI configuration\n"); > > > > + cal_sel = 0; > > > > + write_master(seninf_base, SENINF_TOP_PHY_SENINF_CTL_CSI0, > > > > + ((0 << 0) | (2 << 8) | > > > > + (pcsi_mipi->enable << 31)), 0x80000701); > > > > + } > > > > Could you use switch-statement here as well? > Got it and fixed. > > > > > > + > > > > + /*First Enable Sensor interface and select pad (0x1a04_0200)*/ > > > > + write_master(pseninf, SENINF1_CTRL, > > > > + pcsi_mipi->enable << 0, 0x00000001); > > > > + write_master(pseninf, SENINF1_CTRL, > > > > + pcsi_mipi->pad_sel << 28, 0x70000000); > > > > + > > > > + if (pcsi_mipi->csi_type == CSI2_1_5G || > > > > + pcsi_mipi->csi_type == CSI2_2_5G) { > > > > + write_master(pseninf, SENINF1_CTRL, 0 << 12, 0x0000F000); > > > > + write_master(pseninf, SENINF1_CTRL_EXT, > > > > + (pcsi_mipi->enable << 6) | (0 << 5), 0x00000060); > > > > + } > > > > + if (!pcsi_mipi->enable) { > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_CTL, > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_CTL) & > > > > + 0xFFFFFFE0); > > > > + /* disable mipi BG */ > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (0 << 3) | (0 << 2), 0x0000000C); > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (0 << 3) | (0 << 2), 0x0000000C); > > > > + return ret; > > > > + } > > > > + > > > > + if (pcsi_mipi->csi_type != CSI2_2_5G_CPHY) { /* Dphy */ > > > > + /* set analog phy mode to DPHY */ > > > > + if (IS_CDPHY_COMBO) > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (0 << 0), 0x00000001); > > > > + > > > > + if (IS_4D1C) /* 4D1C (MIPIRX_ANALOG_A_BASE) = 0x00001A42 */ > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (0 << 5) | (1 << 6) | (0 << 8) | > > > > + (1 << 9) | (1 << 11) | (1 << 12), > > > > + 0x00001B60); > > > > + else /*(MIPIRX_ANALOG_BASE) = 0x102;*/ > > > > nit: remove semi-collon for consistency. same for the bellow. > Got it and fixed. > > > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (0 << 5) | (0 << 6) | (1 << 8) | > > > > + (0 << 9) | (0 << 11) | (0 << 12), > > > > + 0x00001B60); > > > > + > > > > + if (IS_CDPHY_COMBO) > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (0 << 0), 0x00000001); > > > > + > > > > + /*only 4d1c need set CSIB (MIPIRX_ANALOG_B_BASE) = 0x00001242*/ > > > > + if (IS_4D1C) > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (0 << 5) | (1 << 6) | (0 << 8) | > > > > + (1 << 9) | (0 << 11) | (1 << 12), > > > > + 0x00001B60); > > > > + else /*(MIPIRX_ANALOG_BASE) = 0x102;*/ > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (0 << 6) | (1 << 8) | (1 << 9) | > > > > + (0 << 11) | (0 << 12), > > > > + 0x00001B40); > > > > + > > > > + /* byte clock invert*/ > > > > + write_master(pmipi_rx, MIPI_RX_ANAA8_CSI0A, > > > > + (1 << 0) | (1 << 1) | (1 << 2), 0x00000007); > > > > + if (IS_4D1C) > > > > + write_master(pmipi_rx, MIPI_RX_ANAA8_CSI0B, > > > > + (1 << 0) | (1 << 1) | (1 << 2), > > > > + 0x00000007); > > > > + > > > > + /*start ANA EQ tuning*/ > > > > + if (IS_CDPHY_COMBO) { > > > > + write_master(pmipi_rx, MIPI_RX_ANA18_CSI0A, > > > > + (1 << 4) | (1 << 6), 0x000000F0); > > > > + write_master(pmipi_rx, MIPI_RX_ANA1C_CSI0A, > > > > + (1 << 20) | (1 << 22), 0x00F00000); > > > > + write_master(pmipi_rx, MIPI_RX_ANA20_CSI0A, > > > > + (1 << 20) | (1 << 22), 0x00F00000); > > > > + > > > > + if (IS_4D1C) { /* 4d1c */ > > > > + write_master(pmipi_rx, MIPI_RX_ANA18_CSI0B, > > > > + (1 << 4) | (1 << 6), 0x000000F0); > > > > + write_master(pmipi_rx, MIPI_RX_ANA1C_CSI0B, > > > > + (1 << 20) | (1 << 22), > > > > + 0x00F00000); > > > > + write_master(pmipi_rx, MIPI_RX_ANA20_CSI0B, > > > > + (1 << 20) | (1 << 22), > > > > + 0x00F00000); > > > > + } > > > > + } else { > > > > + void *pdhy_ana_base = pmipi_rx; > > > > Why don't you use |pmipi_rx| as is? > Got it, remove pdhy_ana_base, use pmipi_rx directly. > > > > > > + > > > > + write_master(pdhy_ana_base, MIPI_RX_ANA18_CSI1A, > > > > + (1 << 4) | (1 << 6) | (1 << 20) | > > > > + (1 << 22), 0x00F000F0); > > > > + write_master(pdhy_ana_base, MIPI_RX_ANA1C_CSI1A, > > > > + (1 << 4) | (1 << 6), 0x000000F0); > > > > + > > > > + if (IS_4D1C) { /* 4d1c */ > > > > + write_master(pdhy_ana_base, > > > > + MIPI_RX_ANA18_CSI1B, (1 << 4) | > > > > + (1 << 6) | (1 << 20) | > > > > + (1 << 22), 0x00F000F0); > > > > + write_master(pdhy_ana_base, > > > > + MIPI_RX_ANA1C_CSI1B, (1 << 4) | > > > > + (1 << 6), 0x000000F0); > > > > + } > > > > + } > > > > + /*end ANA EQ tuning*/ > > > > huge nit: add a blank line. > Got it and fixed. > > > > > > + seninf_write_reg(pmipi_rx_base, MIPI_RX_ANA40_CSI0A, 0x90); > > > > + write_master(pmipi_rx, MIPI_RX_ANA24_CSI0A, > > > > + (0x40 << 24), 0xFF000000); > > > > + if (IS_4D1C) > > > > + write_master(pmipi_rx, MIPI_RX_ANA24_CSI0B, > > > > + (0x40 << 24), 0xFF000000); > > > > + write_master(pmipi_rx, MIPI_RX_WRAPPER80_CSI0A, > > > > + (0 << 16), 0x00030000); > > > > + if (IS_4D1C) > > > > + write_master(pmipi_rx, MIPI_RX_WRAPPER80_CSI0B, > > > > + (0 << 16), 0x00030000); > > > > + /*ANA power on*/ > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (1 << 3), 0x00000008); > > > > + if (IS_4D1C) > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (1 << 3), 0x00000008); > > > > + usleep_range(20, 40); > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (1 << 3), 0x00000008); > > > > + if (IS_4D1C) > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (1 << 2), 0x00000004); > > > > + udelay(1); > > > > +#ifdef CSI2_SW_OFFSET_CAL > > > > + pr_debug("CSI offset calibration start"); > > > > nit: add '\n'. > > Same for other pr_debug below. > Got it and fixed all. > > > > > > + if (IS_CDPHY_COMBO) { > > > > + write_master(pmipi_rx, MIPI_RX_ANA18_CSI0A, > > > > + (1 << 0), 0x00000001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA1C_CSI0A, > > > > + (1 << 0), 0x00000001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA20_CSI0A, > > > > + (1 << 0), 0x00000001); > > > > + > > > > + if (IS_4D1C) { > > > > + write_master(pmipi_rx, MIPI_RX_ANA18_CSI0B, > > > > + (1 << 0), 0x00000001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA1C_CSI0B, > > > > + (1 << 0), 0x00000001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA20_CSI0B, > > > > + (1 << 0), 0x00000001); > > > > + } > > > > + } else { > > > > + void *pdhy_ana_base = pmipi_rx; > > > > same. > > > > > > + > > > > + write_master(pdhy_ana_base, MIPI_RX_ANA18_CSI1A, > > > > + (1 << 0) | (1 << 16), 0x00010001); > > > > + write_master(pdhy_ana_base, MIPI_RX_ANA1C_CSI1A, > > > > + (1 << 0), 0x00000001); > > > > + if (IS_4D1C) { > > > > + write_master(pdhy_ana_base, MIPI_RX_ANA18_CSI1B, > > > > + (1 << 0) | (1 << 16), 0x00010001); > > > > + write_master(pdhy_ana_base, MIPI_RX_ANA1C_CSI1B, > > > > + (1 << 0), 0x00000001); > > > > + } > > > > + } > > > > + udelay(1); > > > > + int status = 0; > > > > + int i = 0; > > > > You can declare variables only at the beginning of scopes. > > I guess you can find warnings while building. > > (Or, you might have forgotten to test this code because here is inside > > of #ifdef) > Got it and fixed. > > > > > > + > > > > + while (1) { > > > > + status = seninf_read_reg(pmipi_rx, MIPI_RX_ANA48_CSI0A); > > > > + if ((IS_CDPHY_COMBO) && (status & (1 << 0)) && > > > > + (status & (1 << 3)) && (status & (1 << 5))) > > > > + break; > > > > + else if ((status & (1 << 3)) && (status & (1 << 4)) && > > > > + (status & (1 << 5))) > > > > + break; > > > > + > > > > + pr_debug("CSIA offset calibration ongoing"); > > > > + i++; > > > > + if (i > 100) { > > > > + pr_debug("CSIA offset calibration timeout"); > > > > + break; > > > > + } > > > > + usleep_range(20, 40); > > > > + } > > > > + if (IS_4D1C) { > > > > + i = 0; > > > > + status = 0; > > > > nit: no need to re-initialize |statue| here. > Got it and fixed. > > > > > > + > > > > + while (1) { > > > > + status = seninf_read_reg(pmipi_rx, > > > > + MIPI_RX_ANA48_CSI0B); > > > > + if ((IS_CDPHY_COMBO) && (status & (1 << 0)) && > > > > + (status & (1 << 3)) && (status & (1 << 5))) > > > > + break; > > > > + else if ((status & (1 << 3)) && (status & > > > > + (1 << 4)) && (status & (1 << 5))) > > > > + break; > > > > + > > > > + pr_debug("CSIB offset calibration ongoing"); > > > > + i++; > > > > + if (i > 100) { > > > > + pr_debug("offset calibration timeout"); > > > > + break; > > > > + } > > > > + usleep_range(20, 40); > > > > + } > > > > + } > > > > + pr_debug("CSI offset calibration end 0x%x, 0x%x", > > > > + seninf_read_reg(pmipi_rx, MIPI_RX_ANA48_CSI0A), > > > > + seninf_read_reg(pmipi_rx, MIPI_RX_ANA48_CSI0B)); > > > > +#endif > > > > + if (IS_4D1C) { /* 4d1c (MIPIRX_CONFIG_CSI_BASE) =0xC9000000; */ > > > > + write_master(pmipi_rx_conf, MIPI_RX_CON24_CSI0, > > > > + (1 << 24) | (2 << 26) | (0 << 28) | > > > > + (3 << 30), 0xFF000000); > > > > + } else { /* 2d1c (MIPIRX_CONFIG_CSI_BASE) =0xE4000000; */ > > > > + write_master(pmipi_rx_conf, MIPI_RX_CON24_CSI0, > > > > + (0 << 24) | (1 << 26) | (2 << 28) | > > > > + (3 << 30), 0xFF000000); > > > > + } > > > > + pr_debug("pcsi_mipi->CSI2_IP %d, MIPI_RX_CON24_CSI0 0x%x", > > > > + csi_info->port, > > > > + seninf_read_reg(pmipi_rx_conf, MIPI_RX_CON24_CSI0)); > > > > + usleep_range(20, 40); > > > > + /*D-PHY SW Delay Line calibration*/ > > > > + } else { /*Cphy setting for CSI0 */ > > > > + /* byte clock invert*/ > > > > + int status = 0; > > > > + int i = 0; > > > > + > > > > + write_master(pmipi_rx, MIPI_RX_ANAA8_CSI0A, > > > > + (1 << 0) | (1 << 2), 0x00000005); > > > > + write_master(pmipi_rx, MIPI_RX_ANAA8_CSI0B, > > > > + (1 << 0) | (1 << 2), 0x00000005); > > > > + /*EQ Power to Enhance Speed*/ > > > > + write_master(pmipi_rx, MIPI_RX_ANA18_CSI0A, > > > > + (1 << 6) | (1 << 22), 0x00C000C0); > > > > + write_master(pmipi_rx, MIPI_RX_ANA1C_CSI0A, > > > > + (1 << 6) | (1 << 22), 0x00C000C0); > > > > + write_master(pmipi_rx, MIPI_RX_ANA20_CSI0A, > > > > + (1 << 6) | (1 << 22), 0x00C000C0); > > > > + write_master(pmipi_rx, MIPI_RX_ANA18_CSI0B, > > > > + (1 << 6) | (1 << 22), 0x00C000C0); > > > > + write_master(pmipi_rx, MIPI_RX_ANA1C_CSI0B, > > > > + (1 << 6) | (1 << 22), 0x00C000C0); > > > > + write_master(pmipi_rx, MIPI_RX_ANA20_CSI0B, > > > > + (1 << 6) | (1 << 22), 0x00C000C0); > > > > + > > > > + /*CDR register setting*/ > > > > + > > > > + *((int *)(priv->csi2_rx[csi_info->port] + 0x30)) = 0x06040404; > > > > + *((int *)(priv->csi2_rx[csi_info->port] + 0x3c)) = 0x06040404; > > > > + *((int *)(priv->csi2_rx[csi_info->port] + 0x34)) = 0x1; > > > > + *((int *)(priv->csi2_rx[csi_info->port] + 0x28)) = 0x1; > > > > + > > > > + *((int *)(priv->csi2_rx[csi_info->port] + 0x1030)) = > > > > + 0x06040404; > > > > + *((int *)(priv->csi2_rx[csi_info->port] + 0x103c)) = > > > > + 0x06040404; > > > > + *((int *)(priv->csi2_rx[csi_info->port] + 0x1034)) = 0x1; > > > > + *((int *)(priv->csi2_rx[csi_info->port] + 0x1028)) = 0x1; > > > > + > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (1 << 0) | (0 << 5) | (0 << 6) | (0 << 8) | > > > > + (0 << 9) | (0 < 11) | (0 < 12), 0x00001B61); > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (1 << 0) | (0 << 5) | (0 << 6) | (0 << 8) | > > > > + (0 << 9) | (0 < 11) | (0 < 12), 0x00001B61); > > > > + /*Power on DPHY*/ > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (1 << 3), 0x00000008); > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (1 << 3), 0x00000008); > > > > + usleep_range(20, 40); > > > > + /*Enable LPF*/ > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (1 << 2), 0x00000004); > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (1 << 2), 0x00000004); > > > > + udelay(1); > > > > + /*offset calibration*/ > > > > + write_master(pmipi_rx, MIPI_RX_ANA18_CSI0A, > > > > + (1 << 0) | (1 << 16), 0x00010001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA1C_CSI0A, > > > > + (1 << 0) | (1 << 16), 0x00010001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA20_CSI0A, > > > > + (1 << 0) | (1 << 16), 0x00010001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA18_CSI0B, > > > > + (1 << 0) | (1 << 16), 0x00010001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA1C_CSI0B, > > > > + (1 << 0) | (1 << 16), 0x00010001); > > > > + write_master(pmipi_rx, MIPI_RX_ANA20_CSI0B, > > > > + (1 << 0) | (1 << 16), 0x00010001); > > > > + udelay(1); > > > > + while (1) { > > > > + status = seninf_read_reg(pmipi_rx, > > > > + MIPI_RX_ANA48_CSI0A); > > > > + if ((status & 0x3f) == 0x3f) > > > > + break; > > > > + i++; > > > > + if (i > 100) { > > > > + pr_debug("CSIA offset calibration timeout"); > > > > + break; > > > > + } > > > > + usleep_range(20, 40); > > > > + } > > > > + > > > > + i = 0; > > > > + status = 0; > > > > nit: no need to re-initialize |statue| here. > Got it and fixed. > > > > > > + while (1) { > > > > + status = seninf_read_reg(pmipi_rx, > > > > + MIPI_RX_ANA48_CSI0B); > > > > + if ((status & 0x3f) == 0x3f) > > > > + break; > > > > + i++; > > > > + if (i > 100) { > > > > + pr_debug("CSIB offset calibration timeout"); > > > > + break; > > > > + } > > > > + usleep_range(20, 40); > > > > + } > > > > + } > > > > + /* End of CSI MIPI */ > > > > + /* DPCM Enable */ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_DPCM, > > > > + 1 << ((pcsi_mipi->dpcm == 0x2a) > > > > + ? 15 : ((pcsi_mipi->dpcm & 0xF) + 7))); > > > > + > > > > + pr_debug("CSI2-%d cnt:%d LaneNum:%d CSI2_EN:%d HeadOrder:%d dpcm:%d\n", > > > > + cal_sel, SENINF_SETTLE_DELAY, > > > > + (int)(pcsi_mipi->data_lane_num + 1), (int)pcsi_mipi->enable, > > > > + (int)pcsi_mipi->data_header_order, (int)pcsi_mipi->dpcm); > > > > + > > > > + /*Settle delay*/ > > > > + write_master(pseninf, SENINF1_CSI2_LNRD_TIMING, > > > > + (SENINF_SETTLE_DELAY << 8), 0x0000FF00); > > > > + /*CSI2 control*/ > > > > + if (pcsi_mipi->csi_type != CSI2_2_5G_CPHY) { /*DPhy*/ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_CTL, > > > > + (seninf_read_reg(pseninf, SENINF1_CSI2_CTL) | > > > > + (pcsi_mipi->data_header_order << 16) | > > > > + (pcsi_mipi->enable << 4) | > > > > + (((1 << (pcsi_mipi->data_lane_num + 1)) - 1) > > > > + ))); > > > > + write_master(pseninf, SENINF1_CSI2_RESYNC_MERGE_CTL, > > > > + (0 << 10) | (0 << 11) | (3 << 0), 0x00000C07); > > > > + write_master(pseninf, SENINF1_CSI2_MODE, > > > > + (0 << 0) | (0 << 8), 0x000007FF); > > > > + write_master(pseninf, SENINF1_CSI2_DPHY_SYNC, > > > > + (0xff00 << 0) | (0x001d << 16), 0xFFFFFFFF); > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_SPARE0, > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_SPARE0) > > > > + & 0xFFFFFFFE); > > > > + } else { /*CPhy*/ > > > > + write_master(pseninf, SENINF1_CSI2_LNRD_TIMING, > > > > + (0 << 0), 0x000000FF); > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_CTL, > > > > + (seninf_read_reg(pseninf, SENINF1_CSI2_CTL) | > > > > + pcsi_mipi->data_header_order << 16)); > > > > + temp = (pcsi_mipi->data_lane_num == SENSOR_MIPI_1_LANE) ? 1 : > > > > + (pcsi_mipi->data_lane_num == SENSOR_MIPI_2_LANE) ? 2 : > > > > + (pcsi_mipi->data_lane_num == SENSOR_MIPI_3_LANE) ? > > > > + 4 : 5; > > > > + write_master(pseninf, SENINF1_CSI2_MODE, > > > > + (temp << 8), 0x00000700); > > > > + temp = pcsi_mipi->data_lane_num >= SENSOR_MIPI_1_LANE; > > > > + write_master(pseninf, SENINF1_CSI2_CTRL_TRIO_CON, > > > > + (temp << 0), 0x00000001); > > > > + temp = pcsi_mipi->data_lane_num >= SENSOR_MIPI_2_LANE; > > > > + write_master(pseninf, SENINF1_CSI2_CTRL_TRIO_CON, > > > > + (temp << 2), 0x00000004); > > > > + temp = pcsi_mipi->data_lane_num >= SENSOR_MIPI_3_LANE; > > > > + write_master(pseninf, SENINF1_CSI2_CTRL_TRIO_CON, > > > > + (temp << 4), 0x00000010); > > > > + temp = pcsi_mipi->data_lane_num >= SENSOR_MIPI_4_LANE; > > > > + write_master(pseninf, SENINF1_CSI2_CTRL_TRIO_CON, > > > > + (temp << 6), 0x00000040); > > > > + write_master(pseninf, SENINF1_CSI2_MODE, > > > > + (0x2 << 0), 0x000000FF); > > > > + write_master(pseninf, SENINF1_CSI2_RESYNC_MERGE_CTL, > > > > + (3 << 0) | (0 << 10) | (1 << 11), 0x00000C07); > > > > + write_master(pseninf, SENINF1_SYNC_RESYNC_CTL, > > > > + (1 << 0), 0x00000007); > > > > + write_master(pseninf, SENINF1_POST_DETECT_CTL, > > > > + (1 << 1), 0x00000002); > > > > + > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_SPARE0, > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_SPARE0) > > > > + | 0x1); > > > > + } > > > > + > > > > + write_master(pseninf, SENINF1_CSI2_CTL, (0 << 27) | (0 << 7) | > > > > + (1 << 25), 0x0A000080); > > > > + write_master(pseninf, SENINF1_CSI2_HS_TRAIL, > > > > + (SENINF_HS_TRAIL_PARAMETER << 0), 0x000000FF); > > > > + > > > > + /* set debug port to output packet number */ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_DGB_SEL, 0x8000001A); > > > > + /*Enable CSI2 IRQ mask*/ > > > > + /* turn on all interrupt */ > > > > nit: Do you have any special reason to start this comment with a > > lower-case letter? > > I think it's better to capitalize the first letter in this comment for > > consistency. > > same for the below comments. > Got it and fixed all. > > > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_INT_EN, 0xFFFFFFFF); > > > > + /*write clear CSI2 IRQ*/ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_INT_STATUS, 0xFFFFFFFF); > > > > + /*Enable CSI2 Extend IRQ mask*/ > > > > + /* turn on all interrupt */ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_INT_EN_EXT, 0x0000001f); > > > > + > > > > + write_master(pseninf, SENINF1_CTRL, (1 << 7), 0x00000080); > > > > + udelay(1); > > > > + write_master(pseninf, SENINF1_CTRL, (0 << 7), 0x00000080); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int power_off(struct _seninf *priv, void *pcsi) > > > > +{ > > > > + int ret = 0; > > > > ditto. > > > > > > + struct seninf_csi_mipi *pcsi_mipi = (struct seninf_csi_mipi *)pcsi; > > > > + struct seninf_csi_info *csi_info = pcsi_mipi->csi_info; > > > > + void *pmipi_rx = priv->csi2_rx[csi_info->port]; > > > > + void *pseninf = priv->seninf_ctrl[csi_info->seninf]; > > > > + > > > > + /* disable CSI2(2.5G) first*/ > > > > + seninf_write_reg(pseninf, SENINF1_CSI2_CTL, > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_CTL) > > > > + & 0xFFFFFFE0); > > > > + /* disable mipi BG */ > > > > + switch (csi_info->port) { > > > > + case CFG_CSI_PORT_0A: > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (0 << 3) | (0 << 2), 0x0000000C); > > > > + break; > > > > + case CFG_CSI_PORT_0B: > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (0 << 3) | (0 << 2), 0x0000000C); > > > > + break; > > > > + default: > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0A, > > > > + (0 << 3) | (0 << 2), 0x0000000C); > > > > + write_master(pmipi_rx, MIPI_RX_ANA00_CSI0B, > > > > + (0 << 3) | (0 << 2), 0x0000000C); > > > > + break; > > > > + } > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int map_fmt(struct _seninf *priv) > > > > +{ > > > > + int fmtidx = 0; > > > > + > > > > + switch (priv->format) { > > > > + case MEDIA_BUS_FMT_SBGGR8_1X8: > > > > + case MEDIA_BUS_FMT_SGBRG8_1X8: > > > > + case MEDIA_BUS_FMT_SGRBG8_1X8: > > > > + case MEDIA_BUS_FMT_SRGGB8_1X8: > > > > + fmtidx = 0; > > > > + priv->dpcm = 0; > > > > + break; > > > > + case MEDIA_BUS_FMT_SGRBG10_1X10: > > > > + case MEDIA_BUS_FMT_SRGGB10_1X10: > > > > + case MEDIA_BUS_FMT_SBGGR10_1X10: > > > > + case MEDIA_BUS_FMT_SGBRG10_1X10: > > > > + fmtidx = 1; > > > > + priv->dpcm = 0; > > > > + break; > > > > + case MEDIA_BUS_FMT_SGRBG10_DPCM8_1X8: > > > > + case MEDIA_BUS_FMT_SRGGB10_DPCM8_1X8: > > > > + case MEDIA_BUS_FMT_SBGGR10_DPCM8_1X8: > > > > + case MEDIA_BUS_FMT_SGBRG10_DPCM8_1X8: > > > > + fmtidx = 1; > > > > + priv->dpcm = 1; > > > > + break; > > > > + case MEDIA_BUS_FMT_SBGGR12_1X12: > > > > + case MEDIA_BUS_FMT_SGBRG12_1X12: > > > > + case MEDIA_BUS_FMT_SGRBG12_1X12: > > > > + case MEDIA_BUS_FMT_SRGGB12_1X12: > > > > + fmtidx = 2; > > > > + priv->dpcm = 0; > > > > + break; > > > > + case MEDIA_BUS_FMT_UYVY8_1X16: > > > > + case MEDIA_BUS_FMT_VYUY8_1X16: > > > > + case MEDIA_BUS_FMT_YUYV8_1X16: > > > > + case MEDIA_BUS_FMT_YVYU8_1X16: > > > > + fmtidx = 3; > > > > + priv->dpcm = 0; > > > > + break; > > > > + default: > > > > + WARN(1, "CSI2: pixel format %08x unsupported!\n", > > > > + priv->format); > > > > + } > > > > + return fmtidx; > > > > +} > > > > + > > > > +static int seninf_set_fmt(struct v4l2_subdev *sd, > > > > + struct v4l2_subdev_pad_config *cfg, > > > > + struct v4l2_subdev_format *fmt) > > > > +{ > > > > + struct _seninf *priv = container_of(sd, struct _seninf, subdev); > > > > + > > > > + priv->format = fmt->format.code; > > > > + pr_debug("priv->format 0x%x", priv->format); > > > > + return 0; > > > > +} > > > > + > > > > +static int seninf_s_stream(struct v4l2_subdev *sd, int on) > > > > +{ > > > > + struct _seninf *priv = container_of(sd, struct _seninf, subdev); > > > > + int ret = 0; > > > > + struct seninf_csi_mipi csi_mipi; > > > > + unsigned int input_data_type = RAW_10BIT_FMT; > > > > + struct sensor_vc_info_struct vc_info; > > > > + unsigned int mux_select = 0; > > > > + unsigned int pixel_mode = ONE_PIXEL_MODE; > > > > + struct seninf_csi_info *csi_info; > > > > + unsigned int port; > > > > + unsigned int seninf_src; > > > > + > > > > + unsigned char sensor_hsync_polarity = SENSOR_CLOCK_POLARITY_LOW; > > > > + unsigned char sensor_vsync_polarity = SENSOR_CLOCK_POLARITY_LOW; > > > > + unsigned char sensor_packet_ecc_order = 1; > > > > + unsigned char sensor_mipi_lane_num = > > > > + priv->ep[priv->port].bus.mipi_csi2.num_data_lanes; > > > > + unsigned int mipi_sensor_type = MIPI_OPHY_NCSI2; > > > > + void *pseninf = priv->seninf_hw; > > > > + > > > > + priv->mux_select = mux_select; /* seninfMUXArbitration */ > > > > Hmm, I cannot figure out what this comment means. > No need, remove this comment. > > > > > > + port = priv->port; > > > > + csi_info = get_csi_info(priv, port); > > > > + seninf_src = csi_info->seninf; > > > > + > > > > + pr_debug("seninf csi_info->seninf(%d) port(%d)\n", > > > > + csi_info->seninf, csi_info->port); > > > > + > > > > + /*configureMipi*/ > > > > nit: /* Configure MIPI */ for consistency. > Got it and fixed. > > > > > > + csi_mipi.enable = 1; > > > > + csi_mipi.data_header_order = sensor_packet_ecc_order; > > > > + csi_mipi.data_lane_num = sensor_mipi_lane_num - 1; > > > > + csi_mipi.csi_type = (mipi_sensor_type == MIPI_CPHY) > > > > + ? CSI2_2_5G_CPHY : CSI2_2_5G; > > > > + csi_mipi.csi_info = csi_info; > > > > + > > > > + csi_mipi.pad_sel = PAD_10BIT; > > > > + csi_mipi.dpcm = 0; > > > > + input_data_type = (unsigned int)map_fmt(priv); > > > > + csi_mipi.dpcm = priv->dpcm; > > > > + > > > > + if (on) { > > > > + /* Configure timestamp */ > > > > + write_master(pseninf, SENINF1_CTRL, (1 << 0), 0x00000001); > > > > + write_master(pseninf, SENINF1_CTRL_EXT, (1 << 6), 0x00000040); > > > > + seninf_write_reg(pseninf, SENINF_TG1_TM_STP, > > > > + SENINF_TIMESTAMP_STEP); > > > > + memcpy((void *)&vc_info, (void *)&SENSOR_VC_INFO[0], > > > > + sizeof(struct sensor_vc_info_struct)); > > > > + > > > > + ret = set_virtual_channel(priv, csi_info->seninf, > > > > + (vc_info.vc0_data_type << 2) | > > > > + (vc_info.VC0_ID & 0x03), > > > > + (vc_info.vc1_data_type << 2) | > > > > + (vc_info.VC1_ID & 0x03), > > > > + (vc_info.vc2_data_type << 2) | > > > > + (vc_info.VC2_ID & 0x03), > > > > + (vc_info.vc3_data_type << 2) | > > > > + (vc_info.VC3_ID & 0x03), > > > > + (vc_info.vc4_data_type << 2) | > > > > + (vc_info.VC4_ID & 0x03), > > > > + (vc_info.vc5_data_type << 2) | > > > > + (vc_info.VC5_ID & 0x03)); > > > > + > > > > + set_csi_mipi(priv, (struct seninf_csi_mipi *)&csi_mipi); > > > > + > > > > + enable_mux(priv, mux_select); > > > > + set_mux_ctrl(priv, mux_select, sensor_hsync_polarity ? 0 : 1, > > > > + sensor_vsync_polarity ? 0 : 1, > > > > + MIPI_SENSOR, input_data_type, pixel_mode); > > > > + > > > > + set_top_mux_ctrl(priv, mux_select, seninf_src); > > > > + seninf_write_reg(pseninf, SENINF_TOP_CAM_MUX_CTRL, 0x0); > > > > + } else { > > > > + power_off(priv, &csi_mipi); > > > > + } > > > > + return 0; > > > > return ret;? > > > > > > +}; > > > > + > > > > +static const struct v4l2_subdev_pad_ops seninf_subdev_pad_ops = { > > > > + .set_fmt = seninf_set_fmt, > > > > +}; > > > > + > > > > +static const struct v4l2_subdev_video_ops seninf_subdev_video_ops = { > > > > + .s_stream = seninf_s_stream, > > > > +}; > > > > + > > > > +static struct v4l2_subdev_ops seninf_subdev_ops = { > > > > + .video = &seninf_subdev_video_ops, > > > > + .pad = &seninf_subdev_pad_ops, > > > > +}; > > > > + > > > > +static int seninf_link_setup(struct media_entity *entity, > > > > + const struct media_pad *local, > > > > + const struct media_pad *remote, u32 flags) > > > > +{ > > > > + struct v4l2_subdev *sd; > > > > + struct _seninf *priv; > > > > + > > > > + sd = media_entity_to_v4l2_subdev(entity); > > > > + priv = v4l2_get_subdevdata(sd); > > > > + pr_debug("mtk_seninf: remote %d-%d, local %d-%d", > > > > + remote->entity->graph_obj.id, remote->index, > > > > + local->entity->graph_obj.id, local->index); > > > > + pr_debug("local->flags %d flags %d", local->flags, flags); > > > > + //link seninf-p1 > > > > You need to use /* */-style comment. > > Same for all the comments in this function. > Got it and fixed all. > > > > > > + if ((local->flags & MEDIA_PAD_FL_SOURCE) && > > > > + (flags & MEDIA_LNK_FL_ENABLED)) { > > > > + pr_debug("set seninf port %d", local->index); > > > > + priv->mux_select = local->index; > > > > + //switch(local->index) //select TG Mux > > > > + } > > > > + > > > > + if ((local->flags & MEDIA_PAD_FL_SINK) && > > > > + (flags & MEDIA_LNK_FL_ENABLED)) { > > > > + pr_debug("link sensor-seninf"); > > > > + priv->port = local->index; > > > > + } > > > > + //seninf internal use force enable create link > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static const struct media_entity_operations seninf_media_ops = { > > > > + .link_setup = seninf_link_setup, > > > > + .link_validate = v4l2_subdev_link_validate, > > > > +}; > > > > + > > > > +#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API > > > > +static int seninf_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) > > > > +{ > > > > + struct _seninf *priv = container_of(sd, struct _seninf, subdev); > > > > + int ret = 0; > > > > + > > > > + ret = pm_runtime_get_sync(priv->dev); > > > > + if (ret < 0) > > > > + dev_err(priv->dev, "Failed to pm_runtime_get_sync: %d\n", ret); > > > > I'm not sure, but should we call clk_prepare_enable even when > > pm_runtime_get_sync fails? > Got it and fixed, return when pm_runtime_get_sync fail. > > > > > > + > > > > + clk_prepare_enable(priv->cam_clk); > > > > + clk_prepare_enable(priv->top_mux_clk); > > > > + return 0; > > > > return ret;? > > > > > > +} > > > > + > > > > +static int seninf_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) > > > > +{ > > > > + struct _seninf *priv = container_of(sd, struct _seninf, subdev); > > > > + > > > > + clk_disable_unprepare(priv->top_mux_clk); > > > > + clk_disable_unprepare(priv->cam_clk); > > > > + pm_runtime_put(priv->dev); > > > > + return 0; > > > > +} > > > > +#endif > > > > + > > > > +#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API > > > > +static const struct v4l2_subdev_internal_ops seninf_internal_ops = { > > > > + .open = seninf_open, > > > > + .close = seninf_close, > > > > +}; > > > > +#endif > > > > + > > > > +static irqreturn_t seninf_irq(int irq, void *device_id) > > > > +{ > > > > + return IRQ_HANDLED; > > > > +} > > > > + > > > > +static int seninf_enable_test_pattern(struct _seninf *priv, u32 pattern) > > > > +{ > > > > + void *pseninf = priv->seninf_hw; > > > > + > > > > + switch (pattern) { > > > > + case TEST_DISABLED: > > > > + case TEST_PATTERN_MODE: > > > > + break; > > > > + case TEST_DEBUG_MODE: > > > > + /*Sensor Interface Control */ > > > > + pr_debug("SENINF_CSI2_CTL SENINF1:0x%x, 2:0x%x, 3:0x%x, 5:0x%x\n", > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_CTL), > > > > + seninf_read_reg(pseninf, SENINF2_CSI2_CTL), > > > > + seninf_read_reg(pseninf, SENINF3_CSI2_CTL), > > > > + seninf_read_reg(pseninf, SENINF5_CSI2_CTL)); > > > > + /*read width/height*/ > > > > + /*read interrupt status*/ > > > > + pr_debug("SENINF1_IRQ:0x%x, 2:0x%x, 3:0x%x, 5:0x%x\n", > > > > + seninf_read_reg(pseninf, SENINF1_CSI2_INT_STATUS), > > > > + seninf_read_reg(pseninf, SENINF2_CSI2_INT_STATUS), > > > > + seninf_read_reg(pseninf, SENINF3_CSI2_INT_STATUS), > > > > + seninf_read_reg(pseninf, SENINF5_CSI2_INT_STATUS)); > > > > + /*Mux1 */ > > > > + pr_debug("SENINF1_MUX_CTRL:0x%x, INTSTA:0x%x, DEBUG_2(0x%x)\n", > > > > + seninf_read_reg(pseninf, SENINF1_MUX_CTRL), > > > > + seninf_read_reg(pseninf, SENINF1_MUX_INTSTA), > > > > + seninf_read_reg(pseninf, SENINF1_MUX_DEBUG_2)); > > > > + if (seninf_read_reg(pseninf, SENINF1_MUX_INTSTA) & 0x1) { > > > > + seninf_write_reg(pseninf, SENINF1_MUX_INTSTA, > > > > + 0xffffffff); > > > > + udelay(SENINF_DRV_DEBUG_DELAY); > > > > + pr_debug("overrun CTRL:%x INTSTA:%x DEBUG_2:%x\n", > > > > + seninf_read_reg(pseninf, SENINF1_MUX_CTRL), > > > > + seninf_read_reg(pseninf, SENINF1_MUX_INTSTA), > > > > + seninf_read_reg(pseninf, SENINF1_MUX_DEBUG_2)); > > > > + } > > > > + break; > > > > + default: > > > > + dev_warn(priv->dev, "%s Unhandled testcase:%d\n", > > > > + __func__, pattern); > > > > + break; > > > > + } > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static int seninf_set_ctrl(struct v4l2_ctrl *ctrl) > > > > +{ > > > > + struct _seninf *priv = container_of(ctrl->handler, > > > > + struct _seninf, ctrl_handler); > > > > + int ret = 0; > > > > + > > > > + switch (ctrl->id) { > > > > + case V4L2_CID_TEST_PATTERN: > > > > + ret = seninf_enable_test_pattern(priv, ctrl->val); > > > > + break; > > > > + default: > > > > + dev_warn(priv->dev, "%s Unhandled id:0x%x, val:0x%x\n", > > > > + __func__, ctrl->id, ctrl->val); > > > > + break; > > > > + } > > > > + return ret; > > > > +} > > > > + > > > > +static const struct v4l2_ctrl_ops seninf_ctrl_ops = { > > > > + .s_ctrl = seninf_set_ctrl, > > > > +}; > > > > + > > > > +static const char * const seninf_test_pattern_menu[] = { > > > > + "Disabled", > > > > + "test_pattern_mode", > > > > + "test_debug_mode", > > > > +}; > > > > + > > > > +static int seninf_initialize_controls(struct _seninf *priv) > > > > +{ > > > > + struct v4l2_ctrl_handler *handler; > > > > + int ret = 0; > > > > + > > > > + handler = &priv->ctrl_handler; > > > > + ret = v4l2_ctrl_handler_init(handler, 2); > > > > + if (ret) > > > > + return ret; > > > > + priv->test_pattern = > > > > + v4l2_ctrl_new_std_menu_items(handler, &seninf_ctrl_ops, > > > > + V4L2_CID_TEST_PATTERN, > > > > + ARRAY_SIZE(seninf_test_pattern_menu) - 1, > > > > + 0, 0, seninf_test_pattern_menu); > > > > + > > > > + if (handler->error) { > > > > + ret = handler->error; > > > > + dev_err(priv->dev, > > > > + "Failed to init controls(%d)\n", ret); > > > > + goto err_free_handler; > > > > + } > > > > + > > > > + priv->subdev.ctrl_handler = handler; > > > > + > > > > + return 0; > > > > + > > > > +err_free_handler: > > > > + v4l2_ctrl_handler_free(handler); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int seninf_probe(struct platform_device *pdev) > > > > +{ > > > > + struct resource *res; > > > > + unsigned int irq; > > > > + int i = 0; > > > > + int ret = 0; > > > > + struct _seninf *priv; > > > > + struct v4l2_subdev *sd; > > > > + struct device_node *endpoint = NULL; > > > > + struct device *dev = &pdev->dev; > > > > + struct media_pad *pads; > > > > + unsigned int irq_info[3]; > > > > + > > > > + dev_dbg(dev, "seninf probe +\n"); > > > > + priv = devm_kzalloc(&pdev->dev, sizeof(struct _seninf), GFP_KERNEL); > > > > + if (!priv) > > > > + return -ENOMEM; > > > > + memset(priv, 0, sizeof(struct _seninf)); > > > > + priv->dev = &pdev->dev; > > > > + sd = &priv->subdev; > > > > + pads = priv->pads; > > > > + /* cam0 <reg 0> */ > > > > + /* cam1 <reg 1> */ > > > > + for (i = 0; i < 2; i++) { /* support upto 2 senosrs */ > > > > + endpoint = of_graph_get_endpoint_by_regs(dev->of_node, i, i); > > > > + if (!endpoint) { > > > > + dev_err(dev, "endpoint node not found\n"); > > > > + return -EINVAL; > > > > + } > > > > + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(endpoint), > > > > + &priv->ep[i]); > > > > + of_node_put(endpoint); > > > > + > > > > + if (ret < 0) { > > > > + pr_err("parsing endpoint node failed\n"); > > > > + return ret; > > > > + } > > > > + if (priv->ep[i].bus_type != V4L2_MBUS_CSI2) { > > > > + pr_err("invalid bus type, must be CSI2\n"); > > > > + return -EINVAL; > > > > + } > > > > + pr_debug("bus.mipi_csi2.num_data_lanes %d\n", > > > > + priv->ep[i].bus.mipi_csi2.num_data_lanes); > > > > + } > > > > + /* get IRQ ID and request IRQ */ > > > > + irq = irq_of_parse_and_map(pdev->dev.of_node, 0); > > > > + > > > > + if (irq > 0) { > > > > nit: if(irq) > > because irq is unsigned. > Got it and fixed. > > > > > > + /* Get IRQ Flag from device node */ > > > > + if (of_property_read_u32_array(pdev->dev.of_node, > > > > + "interrupts", irq_info, > > > > + ARRAY_SIZE(irq_info))) { > > > > + dev_err(dev, "get irq flags from DTS fail!!\n"); > > > > + return -ENODEV; > > > > + } > > > > + ret = request_irq(irq, (irq_handler_t)seninf_irq, > > > > + irq_info[2], "SENINF", NULL); > > > > + if (ret) { > > > > + dev_err(dev, "request_irq fail\n"); > > > > + return ret; > > > > + } > > > > + pr_debug("seninf devnode:%s, irq=%d\n", > > > > + pdev->dev.of_node->name, irq); > > > > + } else { > > > > + pr_debug("No IRQ!!\n"); > > > > This debug message should be "No IRQ found\n" or something like this? > > By the way, should we proceed even if |irq| is 0? > Got it, return when No IRQ found. > > > > > > + } > > > > + > > > > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "base_reg"); > > > > + priv->base_reg = devm_ioremap_resource(dev, res); > > > > + if (IS_ERR(priv->base_reg)) > > > > + return PTR_ERR(priv->base_reg); > > > > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rx_reg"); > > > > + priv->rx_reg = devm_ioremap_resource(dev, res); > > > > + if (IS_ERR(priv->rx_reg)) > > > > + return PTR_ERR(priv->rx_reg); > > > > + > > > > + priv->csi2_rx[CFG_CSI_PORT_0] = priv->rx_reg; > > > > + priv->csi2_rx[CFG_CSI_PORT_0A] = priv->rx_reg; > > > > + priv->csi2_rx[CFG_CSI_PORT_0B] = priv->rx_reg + 0x1000; > > > > + priv->csi2_rx[CFG_CSI_PORT_1] = priv->rx_reg + 0x2000; > > > > + priv->csi2_rx[CFG_CSI_PORT_2] = priv->rx_reg + 0x4000; > > > > + > > > > + priv->seninf_hw = priv->base_reg; > > > > + for (i = 0; i < SENINF_NUM; i++) > > > > + priv->seninf_ctrl[i] = priv->base_reg + 0x1000 * i; > > > > + for (i = 0; i < SENINF_MUX_NUM; i++) > > > > + priv->seninf_mux[i] = priv->base_reg + 0x1000 * i; > > > > + for (i = 0; i < SENINF_NUM; i++) > > > > + priv->csi_rx_conf[i] = priv->base_reg + 0x1000 * i; > > > > + > > > > + priv->cam_clk = devm_clk_get(dev, "CLK_CAM_SENINF"); > > > > + if (IS_ERR(priv->cam_clk)) { > > > > + dev_err(dev, "Failed to get cam_clk\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + priv->top_mux_clk = devm_clk_get(dev, "CLK_TOP_MUX_SENINF"); > > > > + if (IS_ERR(priv->top_mux_clk)) { > > > > + dev_err(dev, "Failed to get top_mux_clk\n"); > > > > + return -EINVAL; > > > > + } > > > > + > > > > + v4l2_subdev_init(sd, &seninf_subdev_ops); > > > > + > > > > + ret = seninf_initialize_controls(priv); > > > > + if (ret) { > > > > + dev_err(dev, "Failed to initialize controls\n"); > > > > + return ret; > > > > + } > > > > +#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API > > > > + sd->internal_ops = &seninf_internal_ops; > > > > + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > > > > +#endif > > > > + priv->subdev.dev = &pdev->dev; > > > > + snprintf(sd->name, V4L2_SUBDEV_NAME_SIZE, "%s.mipi-csi", > > > > + dev_name(&pdev->dev)); > > > > + v4l2_set_subdevdata(sd, priv); > > > > +#if defined(CONFIG_MEDIA_CONTROLLER) > > > > + sd->entity.function = MEDIA_ENT_F_CAM_SENSOR; > > > > + sd->entity.ops = &seninf_media_ops; > > > > + for (i = 0; i < 4; i++) > > > > + pads[i].flags = MEDIA_PAD_FL_SINK; > > > > + for (i = 4; i < NUM_PADS; i++) > > > > + pads[i].flags = MEDIA_PAD_FL_SOURCE; > > > > + ret = media_entity_pads_init(&sd->entity, NUM_PADS, pads); > > > > + if (ret < 0) > > > > + goto err_free_handler; > > > > +#endif > > > > + ret = v4l2_async_register_subdev(sd); > > > > + if (ret < 0) { > > > > + dev_err(dev, "v4l2 async register subdev failed\n"); > > > > + goto err_clean_entity; > > > > + } > > > > + pm_runtime_set_active(dev); > > > > + pm_runtime_enable(dev); > > > > + pm_runtime_idle(dev); > > > > + dev_dbg(dev, "seninf probe -\n"); > > > > + return 0; > > > > + > > > > +err_clean_entity: > > > > +#if defined(CONFIG_MEDIA_CONTROLLER) > > > > + media_entity_cleanup(&sd->entity); > > > > +#endif > > > > +err_free_handler: > > > > + v4l2_ctrl_handler_free(&priv->ctrl_handler); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int seninf_pm_suspend(struct device *dev) > > > > +{ > > > > + pr_debug("seninf_runtime_suspend\n"); > > > > + return 0; > > > > +} > > > > + > > > > +static int seninf_pm_resume(struct device *dev) > > > > +{ > > > > + pr_debug("seninf_runtime_resume\n"); > > > > + return 0; > > > > +} > > > > + > > > > +static const struct dev_pm_ops runtime_pm_ops = { > > > > + SET_RUNTIME_PM_OPS(seninf_pm_suspend, > > > > + seninf_pm_resume, > > > > + NULL) > > > > +}; > > > > + > > > > +static int seninf_remove(struct platform_device *pdev) > > > > +{ > > > > + struct v4l2_subdev *subdev = platform_get_drvdata(pdev); > > > > + struct _seninf *priv = container_of(subdev, struct _seninf, subdev); > > > > + > > > > + v4l2_async_unregister_subdev(&priv->subdev); > > > > + pm_runtime_disable(priv->dev); > > > > + return 0; > > > > +} > > > > + > > > > +#ifdef CONFIG_OF > > > > +static const struct of_device_id mtk_seninf_of_match[] = { > > > > + {.compatible = "mediatek,mt8183-seninf"}, > > > > + {}, > > > > +}; > > > > +MODULE_DEVICE_TABLE(of, mtk_seninf_of_match); > > > > +#endif > > > > + > > > > +static int seninf_suspend(struct platform_device *pdev, pm_message_t mesg) > > > > +{ > > > > + return 0; > > > > +} > > > > + > > > > +static int seninf_resume(struct platform_device *pdev) > > > > +{ > > > > + return 0; > > > > +} > > > > + > > > > +static struct platform_driver seninf_pdrv = { > > > > + .probe = seninf_probe, > > > > + .remove = seninf_remove, > > > > + .suspend = seninf_suspend, > > > > + .resume = seninf_resume, > > > > + .driver = { > > > > + .name = "seninf_0", > > > > + .owner = THIS_MODULE, > > > > +#ifdef CONFIG_OF > > > > + .of_match_table = mtk_seninf_of_match, > > > > +#endif > > > > + .pm = &runtime_pm_ops, > > > > + }, > > > > +}; > > > > + > > > > +static int __init mtk_seninf_init(void) > > > > +{ > > > > + int ret; > > > > + > > > > + pr_debug("seninf Init\n"); > > > > + ret = platform_driver_register(&seninf_pdrv); > > > > + if (ret) { > > > > + pr_err("Failed to register platform driver\n"); > > > > + return ret; > > > > + } > > > > + return 0; > > > > +} > > > > + > > > > +static void __exit mtk_seninf_exit(void) > > > > +{ > > > > + pr_debug("seninf Exit\n"); > > > > + platform_driver_unregister(&seninf_pdrv); > > > > +} > > > > + > > > > +late_initcall(mtk_seninf_init); > > > > +module_exit(mtk_seninf_exit); > > > > + > > > > +MODULE_DESCRIPTION("MTK seninf driver"); > > > > +MODULE_AUTHOR("Louis Kuo <louis.kuo@xxxxxxxxxxxx>"); > > > > +MODULE_LICENSE("GPL v2"); > > > > +MODULE_ALIAS("MTK:mtk_seninf"); > > > > diff --git a/drivers/media/platform/mtk-isp/isp_50/seninf/seninf_drv_def.h b/drivers/media/platform/mtk-isp/isp_50/seninf/seninf_drv_def.h > > > > new file mode 100644 > > > > index 0000000..6280ae4 > > > > --- /dev/null > > > > +++ b/drivers/media/platform/mtk-isp/isp_50/seninf/seninf_drv_def.h > > > > @@ -0,0 +1,201 @@ > > > > +/* SPDX-License-Identifier: GPL-2.0 */ > > > > +/* > > > > + * Copyright (C) 2015 MediaTek Inc. > > > > + * > > > > + * This program is free software: you can redistribute it and/or modify > > > > + * it under the terms of the GNU General Public License version 2 as > > > > + * published by the Free Software Foundation. > > > > + * > > > > + * This program is distributed in the hope that it will be useful, > > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > > + * GNU General Public License for more details. > > > > + */ > > > > + > > > > +#ifndef __SENINF_DRV_DEF_H__ > > > > +#define __SENINF_DRV_DEF_H__ > > > > + > > > > +#if defined(SENINF_CLK_208M) > > > > +#define SENINF_TIMESTAMP_STEP 0x67 > > > > +#define SENINF_SETTLE_DELAY 0x15 > > > > +#define SENINF_HS_TRAIL_PARAMETER 0x8 > > > > +#elif defined(SENINF_CLK_312M) > > > > +#define SENINF_TIMESTAMP_STEP 0x9b > > > > +#define SENINF_SETTLE_DELAY 0x20 > > > > +#define SENINF_HS_TRAIL_PARAMETER 0xa > > > > +#else > > > > +#define SENINF_TIMESTAMP_STEP 0x67 > > > > +#define SENINF_SETTLE_DELAY 0x15 > > > > +#define SENINF_HS_TRAIL_PARAMETER 0x8 > > > > +#endif > > > > + > > > > +#define SENINF_DRV_DEBUG_DELAY 1000 > > > > + > > > > +#define SENSOR_CLOCK_POLARITY_HIGH 0 > > > > +#define SENSOR_CLOCK_POLARITY_LOW 1 > > > > +#define NUM_PADS 12 > > > > + > > > > +enum { > > > > + MIPI_OPHY_NCSI2 = 0, > > > > + MIPI_OPHY_CSI2 = 1, > > > > + MIPI_CPHY = 2, > > > > +}; > > > > + > > > > +struct sensor_vc_info_struct { > > > > + unsigned short vc_num; > > > > + unsigned short vc_pixel_num; > > > > + unsigned short mode_select; /* 0: auto mode, 1:direct mode */ > > > > + unsigned short expo_ratio; /* 1/1, 1/2, 1/4, 1/8 */ > > > > + unsigned short od_value; /* OD Value */ > > > > + unsigned short RG_STATSMODE; /* 0: 16x16, 1:8x8, 2:4x4, 3:1x1*/ > > > > + unsigned short VC0_ID; > > > > + unsigned short vc0_data_type; > > > > + unsigned short VC0_SIZEH; > > > > + unsigned short VC0_SIZEV; > > > > + unsigned short VC1_ID; > > > > + unsigned short vc1_data_type; > > > > + unsigned short VC1_SIZEH; > > > > + unsigned short VC1_SIZEV; > > > > + unsigned short VC2_ID; > > > > + unsigned short vc2_data_type; > > > > + unsigned short VC2_SIZEH; > > > > + unsigned short VC2_SIZEV; > > > > + unsigned short VC3_ID; > > > > + unsigned short vc3_data_type; > > > > + unsigned short VC3_SIZEH; > > > > + unsigned short VC3_SIZEV; > > > > + unsigned short VC4_ID; > > > > + unsigned short vc4_data_type; > > > > + unsigned short VC4_SIZEH; > > > > + unsigned short VC4_SIZEV; > > > > + unsigned short VC5_ID; > > > > + unsigned short vc5_data_type; > > > > + unsigned short VC5_SIZEH; > > > > + unsigned short VC5_SIZEV; > > > > +}; > > > > + > > > > +enum { > > > > + TEST_DISABLED = 0X0, > > > > + TEST_PATTERN_MODE, > > > > + TEST_DEBUG_MODE, > > > > +}; > > > > + > > > > +enum { > > > > + CFG_CSI_PORT_0 = 0x0,/* 4D1C */ > > > > + CFG_CSI_PORT_1, /* 4D1C */ > > > > + CFG_CSI_PORT_2, /* 4D1C */ > > > > + CFG_CSI_PORT_0A, /* 2D1C */ > > > > + CFG_CSI_PORT_0B, /* 2D1C */ > > > > + CFG_CSI_PORT_MAX_NUM, > > > > + CFG_CSI_PORT_NONE /*for non-MIPI sensor */ > > > > +}; > > > > + > > > > +enum { > > > > + ONE_PIXEL_MODE = 0x0, > > > > + TWO_PIXEL_MODE = 0x1, > > > > + FOUR_PIXEL_MODE = 0x2, > > > > +}; > > > > + > > > > +#define SENINF_CAM_MUX_MIN SENINF_MUX1 > > > > +#define SENINF_CAM_MUX_MAX SENINF_MUX3 > > > > +#define SENINF_CAMSV_MUX_MIN SENINF_MUX3 > > > > +#define SENINF_CAMSV_MUX_MAX SENINF_MUX_NUM > > > > + > > > > +#define SENINF_PIXEL_MODE_CAM TWO_PIXEL_MODE > > > > +#define SENINF_PIXEL_MODE_CAMSV FOUR_PIXEL_MODE > > > > + > > > > +#define SENINF_TIMESTAMP_CLK 1000 > > > > + > > > > +enum { > > > > + SENSOR_MIPI_1_LANE = 0, > > > > + SENSOR_MIPI_2_LANE, > > > > + SENSOR_MIPI_3_LANE, > > > > + SENSOR_MIPI_4_LANE > > > > +}; > > > > + > > > > +enum { > > > > + SENINF_MUX1 = 0x0, > > > > + SENINF_MUX2 = 0x1, > > > > + SENINF_MUX3 = 0x2, > > > > + SENINF_MUX4 = 0x3, > > > > + SENINF_MUX5 = 0x4, > > > > + SENINF_MUX6 = 0x5, > > > > + SENINF_MUX_NUM, > > > > + SENINF_MUX_ERROR = -1, > > > > +}; > > > > + > > > > +enum { > > > > + SENINF_1 = 0x0, > > > > + SENINF_2 = 0x1, > > > > + SENINF_3 = 0x2, > > > > + SENINF_4 = 0x3, > > > > + SENINF_5 = 0x4, > > > > + SENINF_NUM, > > > > +}; > > > > + > > > > +enum { > > > > + PAD_10BIT = 0x0, > > > > + PAD_8BIT_7_0 = 0x3, > > > > + PAD_8BIT_9_2 = 0x4, > > > > +}; > > > > + > > > > +enum { /* 0:CSI2(2.5G), 3: parallel, 8:NCSI2(1.5G) */ > > > > + CSI2 = 0x0, /* 2.5G support */ > > > > + TEST_MODEL = 0x1, > > > > + CCIR656 = 0x2, > > > > + PARALLEL_SENSOR = 0x3, > > > > + SERIAL_SENSOR = 0x4, > > > > + HD_TV = 0x5, > > > > + EXT_CSI2_OUT1 = 0x6, > > > > + EXT_CSI2_OUT2 = 0x7, > > > > + MIPI_SENSOR = 0x8,/* 1.5G support */ > > > > + VIRTUAL_CHANNEL_1 = 0x9, > > > > + VIRTUAL_CHANNEL_2 = 0xA, > > > > + VIRTUAL_CHANNEL_3 = 0xB, > > > > + VIRTUAL_CHANNEL_4 = 0xC, > > > > + VIRTUAL_CHANNEL_5 = 0xD, > > > > + VIRTUAL_CHANNEL_6 = 0xE, > > > > +}; > > > > + > > > > +enum { /* 0:CSI2(2.5G), 1:NCSI2(1.5G) */ > > > > + CSI2_1_5G = 0x0, /* 1.5G support */ > > > > + CSI2_2_5G = 0x1, /* 2.5G support*/ > > > > + CSI2_2_5G_CPHY = 0x2, /* 2.5G support*/ > > > > +}; > > > > + > > > > +enum { > > > > + RAW_8BIT_FMT = 0x0, > > > > + RAW_10BIT_FMT = 0x1, > > > > + RAW_12BIT_FMT = 0x2, > > > > + YUV422_FMT = 0x3, > > > > + RAW_14BIT_FMT = 0x4, > > > > + RGB565_MIPI_FMT = 0x5, > > > > + RGB888_MIPI_FMT = 0x6, > > > > + JPEG_FMT = 0x7 > > > > +}; > > > > + > > > > +enum { > > > > + CMD_SENINF_GET_SENINF_ADDR, > > > > + CMD_SENINF_DEBUG_TASK, > > > > + CMD_SENINF_DEBUG_TASK_CAMSV, > > > > + CMD_SENINF_DEBUG_PIXEL_METER, > > > > + CMD_SENINF_MAX > > > > +}; > > > > + > > > > +/* MIPI sensor pad usage */ > > > > +struct seninf_csi_info { > > > > + unsigned int port; > > > > + unsigned int seninf; > > > > +}; > > > > + > > > > +struct seninf_csi_mipi { > > > > + unsigned int enable; > > > > + struct seninf_csi_info *csi_info; > > > > + unsigned int csi_type; > > > > + unsigned int data_lane_num; > > > > + unsigned int dpcm; > > > > + unsigned int data_header_order; > > > > + unsigned int pad_sel; > > > > +}; > > > > + > > > > +#endif /*__SENINF_DRV_DEF_H__ */ > > > > diff --git a/drivers/media/platform/mtk-isp/isp_50/seninf/seninf_reg.h b/drivers/media/platform/mtk-isp/isp_50/seninf/seninf_reg.h > > > > new file mode 100644 > > > > index 0000000..7402630 > > > > --- /dev/null > > > > +++ b/drivers/media/platform/mtk-isp/isp_50/seninf/seninf_reg.h > > > > @@ -0,0 +1,992 @@ > > > > +/* SPDX-License-Identifier: GPL-2.0 */ > > > > +/* > > > > + * Copyright (C) 2015 MediaTek Inc. > > > > + * > > > > + * This program is free software: you can redistribute it and/or modify > > > > + * it under the terms of the GNU General Public License version 2 as > > > > + * published by the Free Software Foundation. > > > > + * > > > > + * This program is distributed in the hope that it will be useful, > > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > > + * GNU General Public License for more details. > > > > + */ > > > > + > > > > +#ifndef _SENINF_REG_H_ > > > > +#define _SENINF_REG_H_ > > > > + > > > > +#define mt_reg_sync_writel(v, a) \ > > > > + do { \ > > > > + __raw_writel((v), (void __force __iomem *)((a))); \ > > > > + /* add memory barrier */ \ > > > > + mb(); \ > > > > + } while (0) > > > > + > > > > +#define seninf_read_reg(reg_base, reg_name) \ > > > > + ((unsigned int)ioread32((reg_base) + (reg_name))) > > > > +#define seninf_write_reg(reg_base, reg_name, value) \ > > > > + mt_reg_sync_writel(value, (reg_base) + (reg_name)) > > > > +#define write_master(reg_base, reg_name, value, mask) \ > > > > + mt_reg_sync_writel(ioread32((reg_base) + (reg_name)) \ > > > > + & (~(mask)) | (value), (reg_base) + (reg_name)) > > > > + > > > > +/* 0x11C80000..0x11C850AC */ > > > > +#define MIPI_RX_ANA00_CSI0A 0x0000 > > > > +#define MIPI_RX_ANA04_CSI0A 0x0004 > > > > +#define MIPI_RX_ANA08_CSI0A 0x0008 > > > > +#define MIPI_RX_ANA0C_CSI0A 0x000C > > > > +#define MIPI_RX_ANA10_CSI0A 0x0010 > > > > +#define MIPI_RX_ANA14_CSI0A 0x0014 > > > > +#define MIPI_RX_ANA18_CSI0A 0x0018 > > > > +#define MIPI_RX_ANA1C_CSI0A 0x001C > > > > +#define MIPI_RX_ANA20_CSI0A 0x0020 > > > > +#define MIPI_RX_ANA24_CSI0A 0x0024 > > > > +#define MIPI_RX_ANA28_CSI0A 0x0028 > > > > +#define MIPI_RX_ANA2C_CSI0A 0x002C > > > > +#define rsv_0030 0x0030 > > > > +#define MIPI_RX_ANA34_CSI0A 0x0034 > > > > +#define MIPI_RX_ANA38_CSI0A 0x0038 > > > > +#define rsv_003C 0x003C > > > > +#define MIPI_RX_ANA40_CSI0A 0x0040 > > > > +#define rsv_0044 0x0044 > > > > +#define MIPI_RX_ANA48_CSI0A 0x0048 > > > > +#define rsv_004C_13 0x004C > > > > +#define MIPI_RX_WRAPPER80_CSI0A 0x0080 > > > > +#define MIPI_RX_WRAPPER84_CSI0A 0x0084 > > > > +#define MIPI_RX_WRAPPER88_CSI0A 0x0088 > > > > +#define MIPI_RX_WRAPPER8C_CSI0A 0x008C > > > > +#define MIPI_RX_WRAPPER90_CSI0A 0x0090 > > > > +#define MIPI_RX_WRAPPER94_CSI0A 0x0094 > > > > +#define MIPI_RX_WRAPPER98_CSI0A 0x0098 > > > > +#define MIPI_RX_WRAPPER9C_CSI0A 0x009C > > > > +#define rsv_00A0 0x00A0 > > > > +#define MIPI_RX_ANAA4_CSI0A 0x00A4 > > > > +#define MIPI_RX_ANAA8_CSI0A 0x00A8 > > > > +#define rsv_00AC_981 0x00AC > > > > +#define MIPI_RX_ANA00_CSI0B 0x1000 > > > > +#define MIPI_RX_ANA04_CSI0B 0x1004 > > > > +#define MIPI_RX_ANA08_CSI0B 0x1008 > > > > +#define MIPI_RX_ANA0C_CSI0B 0x100C > > > > +#define MIPI_RX_ANA10_CSI0B 0x1010 > > > > +#define MIPI_RX_ANA14_CSI0B 0x1014 > > > > +#define MIPI_RX_ANA18_CSI0B 0x1018 > > > > +#define MIPI_RX_ANA1C_CSI0B 0x101C > > > > +#define MIPI_RX_ANA20_CSI0B 0x1020 > > > > +#define MIPI_RX_ANA24_CSI0B 0x1024 > > > > +#define MIPI_RX_ANA28_CSI0B 0x1028 > > > > +#define MIPI_RX_ANA2C_CSI0B 0x102C > > > > +#define rsv_1030 0x1030 > > > > +#define MIPI_RX_ANA34_CSI0B 0x1034 > > > > +#define MIPI_RX_ANA38_CSI0B 0x1038 > > > > +#define rsv_103C_3 0x103C > > > > +#define MIPI_RX_ANA48_CSI0B 0x1048 > > > > +#define rsv_104C_13 0x104C > > > > +#define MIPI_RX_WRAPPER80_CSI0B 0x1080 > > > > +#define MIPI_RX_WRAPPER84_CSI0B 0x1084 > > > > +#define MIPI_RX_WRAPPER88_CSI0B 0x1088 > > > > +#define MIPI_RX_WRAPPER8C_CSI0B 0x108C > > > > +#define MIPI_RX_WRAPPER90_CSI0B 0x1090 > > > > +#define MIPI_RX_WRAPPER94_CSI0B 0x1094 > > > > +#define MIPI_RX_WRAPPER98_CSI0B 0x1098 > > > > +#define MIPI_RX_WRAPPER9C_CSI0B 0x109C > > > > +#define rsv_10A0 0x10A0 > > > > +#define MIPI_RX_ANAA4_CSI0B 0x10A4 > > > > +#define MIPI_RX_ANAA8_CSI0B 0x10A8 > > > > +#define rsv_10AC_981 0x10AC > > > > +#define MIPI_RX_ANA00_CSI1A 0x2000 > > > > +#define MIPI_RX_ANA04_CSI1A 0x2004 > > > > +#define MIPI_RX_ANA08_CSI1A 0x2008 > > > > +#define MIPI_RX_ANA0C_CSI1A 0x200C > > > > +#define MIPI_RX_ANA10_CSI1A 0x2010 > > > > +#define rsv_2014 0x2014 > > > > +#define MIPI_RX_ANA18_CSI1A 0x2018 > > > > +#define MIPI_RX_ANA1C_CSI1A 0x201C > > > > +#define rsv_2020 0x2020 > > > > +#define MIPI_RX_ANA24_CSI1A 0x2024 > > > > +#define rsv_2028_8 0x2028 > > > > +#define MIPI_RX_ANA48_CSI1A 0x2048 > > > > +#define rsv_204C_13 0x204C > > > > +#define MIPI_RX_WRAPPER80_CSI1A 0x2080 > > > > +#define MIPI_RX_WRAPPER84_CSI1A 0x2084 > > > > +#define MIPI_RX_WRAPPER88_CSI1A 0x2088 > > > > +#define MIPI_RX_WRAPPER8C_CSI1A 0x208C > > > > +#define MIPI_RX_WRAPPER90_CSI1A 0x2090 > > > > +#define MIPI_RX_WRAPPER94_CSI1A 0x2094 > > > > +#define MIPI_RX_WRAPPER98_CSI1A 0x2098 > > > > +#define MIPI_RX_WRAPPER9C_CSI1A 0x209C > > > > +#define rsv_20A0 0x20A0 > > > > +#define MIPI_RX_ANAA4_CSI1A 0x20A4 > > > > +#define MIPI_RX_ANAA8_CSI1A 0x20A8 > > > > +#define rsv_20AC_981 0x20AC > > > > +#define MIPI_RX_ANA00_CSI1B 0x3000 > > > > +#define MIPI_RX_ANA04_CSI1B 0x3004 > > > > +#define MIPI_RX_ANA08_CSI1B 0x3008 > > > > +#define MIPI_RX_ANA0C_CSI1B 0x300C > > > > +#define MIPI_RX_ANA10_CSI1B 0x3010 > > > > +#define rsv_3014 0x3014 > > > > +#define MIPI_RX_ANA18_CSI1B 0x3018 > > > > +#define MIPI_RX_ANA1C_CSI1B 0x301C > > > > +#define rsv_3020 0x3020 > > > > +#define MIPI_RX_ANA24_CSI1B 0x3024 > > > > +#define rsv_3028_8 0x3028 > > > > +#define MIPI_RX_ANA48_CSI1B 0x3048 > > > > +#define rsv_304C_13 0x304C > > > > +#define MIPI_RX_WRAPPER80_CSI1B 0x3080 > > > > +#define MIPI_RX_WRAPPER84_CSI1B 0x3084 > > > > +#define MIPI_RX_WRAPPER88_CSI1B 0x3088 > > > > +#define MIPI_RX_WRAPPER8C_CSI1B 0x308C > > > > +#define MIPI_RX_WRAPPER90_CSI1B 0x3090 > > > > +#define MIPI_RX_WRAPPER94_CSI1B 0x3094 > > > > +#define MIPI_RX_WRAPPER98_CSI1B 0x3098 > > > > +#define MIPI_RX_WRAPPER9C_CSI1B 0x309C > > > > +#define rsv_30A0 0x30A0 > > > > +#define MIPI_RX_ANAA4_CSI1B 0x30A4 > > > > +#define MIPI_RX_ANAA8_CSI1B 0x30A8 > > > > +#define rsv_30AC_981 0x30AC > > > > +#define MIPI_RX_ANA00_CSI2A 0x4000 > > > > +#define MIPI_RX_ANA04_CSI2A 0x4004 > > > > +#define MIPI_RX_ANA08_CSI2A 0x4008 > > > > +#define MIPI_RX_ANA0C_CSI2A 0x400C > > > > +#define MIPI_RX_ANA10_CSI2A 0x4010 > > > > +#define rsv_4014 0x4014 > > > > +#define MIPI_RX_ANA18_CSI2A 0x4018 > > > > +#define MIPI_RX_ANA1C_CSI2A 0x401C > > > > +#define rsv_4020 0x4020 > > > > +#define MIPI_RX_ANA24_CSI2A 0x4024 > > > > +#define rsv_4028_8 0x4028 > > > > +#define MIPI_RX_ANA48_CSI2A 0x4048 > > > > +#define rsv_404C_13 0x404C > > > > +#define MIPI_RX_WRAPPER80_CSI2A 0x4080 > > > > +#define MIPI_RX_WRAPPER84_CSI2A 0x4084 > > > > +#define MIPI_RX_WRAPPER88_CSI2A 0x4088 > > > > +#define MIPI_RX_WRAPPER8C_CSI2A 0x408C > > > > +#define MIPI_RX_WRAPPER90_CSI2A 0x4090 > > > > +#define MIPI_RX_WRAPPER94_CSI2A 0x4094 > > > > +#define MIPI_RX_WRAPPER98_CSI2A 0x4098 > > > > +#define MIPI_RX_WRAPPER9C_CSI2A 0x409C > > > > +#define rsv_40A0 0x40A0 > > > > +#define MIPI_RX_ANAA4_CSI2A 0x40A4 > > > > +#define MIPI_RX_ANAA8_CSI2A 0x40A8 > > > > +#define rsv_40AC_981 0x40AC > > > > +#define MIPI_RX_ANA00_CSI2B 0x5000 > > > > +#define MIPI_RX_ANA04_CSI2B 0x5004 > > > > +#define MIPI_RX_ANA08_CSI2B 0x5008 > > > > +#define MIPI_RX_ANA0C_CSI2B 0x500C > > > > +#define MIPI_RX_ANA10_CSI2B 0x5010 > > > > +#define rsv_5014 0x5014 > > > > +#define MIPI_RX_ANA18_CSI2B 0x5018 > > > > +#define MIPI_RX_ANA1C_CSI2B 0x501C > > > > +#define rsv_5020 0x5020 > > > > +#define MIPI_RX_ANA24_CSI2B 0x5024 > > > > +#define rsv_5028_8 0x5028 > > > > +#define MIPI_RX_ANA48_CSI2B 0x5048 > > > > +#define rsv_504C_13 0x504C > > > > +#define MIPI_RX_WRAPPER80_CSI2B 0x5080 > > > > +#define MIPI_RX_WRAPPER84_CSI2B 0x5084 > > > > +#define MIPI_RX_WRAPPER88_CSI2B 0x5088 > > > > +#define MIPI_RX_WRAPPER8C_CSI2B 0x508C > > > > +#define MIPI_RX_WRAPPER90_CSI2B 0x5090 > > > > +#define MIPI_RX_WRAPPER94_CSI2B 0x5094 > > > > +#define MIPI_RX_WRAPPER98_CSI2B 0x5098 > > > > +#define MIPI_RX_WRAPPER9C_CSI2B 0x509C > > > > +#define rsv_50A0 0x50A0 > > > > +#define MIPI_RX_ANAA4_CSI2B 0x50A4 > > > > +#define MIPI_RX_ANAA8_CSI2B 0x50A8 > > > > +#define rsv_50AC_20 0x50AC > > > > + > > > > +/* 0x1A040000..0x1A047D40 */ > > > > +#define SENINF_TOP_CTRL 0x0000 > > > > +#define SENINF_TOP_CMODEL_PAR 0x0004 > > > > +#define SENINF_TOP_MUX_CTRL 0x0008 > > > > +#define rsv_000C 0x000C > > > > +#define SENINF_TOP_CAM_MUX_CTRL 0x0010 > > > > +#define SENINF_TOP_N3D_A_CTL 0x0014 > > > > +#define SENINF_TOP_N3D_B_CTL 0x0018 > > > > +#define SENINF_TOP_PHY_SENINF_CTL_CSI0 0x001C > > > > +#define SENINF_TOP_PHY_SENINF_CTL_CSI1 0x0020 > > > > +#define SENINF_TOP_PHY_SENINF_CTL_CSI2 0x0024 > > > > +#define rsv_0028_54 0x0028 > > > > +#define SENINF_N3D_A_CTL 0x0100 > > > > +#define SENINF_N3D_A_POS 0x0104 > > > > +#define SENINF_N3D_A_TRIG 0x0108 > > > > +#define SENINF_N3D_A_INT 0x010C > > > > +#define SENINF_N3D_A_CNT0 0x0110 > > > > +#define SENINF_N3D_A_CNT1 0x0114 > > > > +#define SENINF_N3D_A_DBG 0x0118 > > > > +#define SENINF_N3D_A_DIFF_THR 0x011C > > > > +#define SENINF_N3D_A_DIFF_CNT 0x0120 > > > > +#define SENINF_N3D_A_DBG_1 0x0124 > > > > +#define SENINF_N3D_A_VALID_TG_CNT 0x0128 > > > > +#define SENINF_N3D_A_SYNC_A_PERIOD 0x012C > > > > +#define SENINF_N3D_A_SYNC_B_PERIOD 0x0130 > > > > +#define SENINF_N3D_A_SYNC_A_PULSE_LEN 0x0134 > > > > +#define SENINF_N3D_A_SYNC_B_PULSE_LEN 0x0138 > > > > +#define SENINF_N3D_A_SUB_CNT 0x013C > > > > +#define SENINF_N3D_A_VSYNC_CNT 0x0140 > > > > +#define rsv_0144_47 0x0144 > > > > +#define SENINF1_CTRL 0x0200 > > > > +#define SENINF1_CTRL_EXT 0x0204 > > > > +#define SENINF1_ASYNC_CTRL 0x0208 > > > > +#define rsv_020C_253 0x020C > > > > +#define SENINF_TG1_PH_CNT 0x0600 > > > > +#define SENINF_TG1_SEN_CK 0x0604 > > > > +#define SENINF_TG1_TM_CTL 0x0608 > > > > +#define SENINF_TG1_TM_SIZE 0x060C > > > > +#define SENINF_TG1_TM_CLK 0x0610 > > > > +#define SENINF_TG1_TM_STP 0x0614 > > > > +#define rsv_0618_131 0x0618 > > > > +#define MIPI_RX_CON24_CSI0 0x0824 > > > > +#define MIPI_RX_CON28_CSI0 0x0828 > > > > +#define rsv_082C_2 0x082C > > > > +#define MIPI_RX_CON34_CSI0 0x0834 > > > > +#define MIPI_RX_CON38_CSI0 0x0838 > > > > +#define MIPI_RX_CON3C_CSI0 0x083C > > > > +#define rsv_0840_15 0x0840 > > > > +#define MIPI_RX_CON7C_CSI0 0x087C > > > > +#define MIPI_RX_CON80_CSI0 0x0880 > > > > +#define MIPI_RX_CON84_CSI0 0x0884 > > > > +#define MIPI_RX_CON88_CSI0 0x0888 > > > > +#define MIPI_RX_CON8C_CSI0 0x088C > > > > +#define MIPI_RX_CON90_CSI0 0x0890 > > > > +#define MIPI_RX_CON94_CSI0 0x0894 > > > > +#define MIPI_RX_CON98_CSI0 0x0898 > > > > +#define rsv_089C 0x089C > > > > +#define MIPI_RX_CONA0_CSI0 0x08A0 > > > > +#define rsv_08A4_3 0x08A4 > > > > +#define MIPI_RX_CONB0_CSI0 0x08B0 > > > > +#define MIPI_RX_CONB4_CSI0 0x08B4 > > > > +#define MIPI_RX_CONB8_CSI0 0x08B8 > > > > +#define MIPI_RX_CONBC_CSI0 0x08BC > > > > +#define MIPI_RX_CONC0_CSI0 0x08C0 > > > > +#define MIPI_RX_CONC4_CSI0 0x08C4 > > > > +#define MIPI_RX_CONC8_CSI0 0x08C8 > > > > +#define MIPI_RX_CONCC_CSI0 0x08CC > > > > +#define MIPI_RX_COND0_CSI0 0x08D0 > > > > +#define rsv_08D4_75 0x08D4 > > > > +#define SENINF1_CSI2_CTL 0x0A00 > > > > +#define SENINF1_CSI2_LNRC_TIMING 0x0A04 > > > > +#define SENINF1_CSI2_LNRD_TIMING 0x0A08 > > > > +#define SENINF1_CSI2_DPCM 0x0A0C > > > > +#define SENINF1_CSI2_INT_EN 0x0A10 > > > > +#define SENINF1_CSI2_INT_STATUS 0x0A14 > > > > +#define SENINF1_CSI2_DGB_SEL 0x0A18 > > > > +#define SENINF1_CSI2_DBG_PORT 0x0A1C > > > > +#define SENINF1_CSI2_SPARE0 0x0A20 > > > > +#define SENINF1_CSI2_SPARE1 0x0A24 > > > > +#define SENINF1_CSI2_LNRC_FSM 0x0A28 > > > > +#define SENINF1_CSI2_LNRD_FSM 0x0A2C > > > > +#define SENINF1_CSI2_FRAME_LINE_NUM 0x0A30 > > > > +#define SENINF1_CSI2_GENERIC_SHORT 0x0A34 > > > > +#define SENINF1_CSI2_HSRX_DBG 0x0A38 > > > > +#define SENINF1_CSI2_DI 0x0A3C > > > > +#define SENINF1_CSI2_HS_TRAIL 0x0A40 > > > > +#define SENINF1_CSI2_DI_CTRL 0x0A44 > > > > +#define rsv_0A48 0x0A48 > > > > +#define SENINF1_CSI2_DETECT_CON1 0x0A4C > > > > +#define SENINF1_CSI2_DETECT_CON2 0x0A50 > > > > +#define SENINF1_CSI2_DETECT_CON3 0x0A54 > > > > +#define SENINF1_CSI2_RLR0_CON0 0x0A58 > > > > +#define SENINF1_CSI2_RLR1_CON0 0x0A5C > > > > +#define SENINF1_CSI2_RLR2_CON0 0x0A60 > > > > +#define SENINF1_CSI2_RLR_CON0 0x0A64 > > > > +#define SENINF1_CSI2_MUX_CON 0x0A68 > > > > +#define SENINF1_CSI2_DETECT_DBG0 0x0A6C > > > > +#define SENINF1_CSI2_DETECT_DBG1 0x0A70 > > > > +#define SENINF1_CSI2_RESYNC_MERGE_CTL 0x0A74 > > > > +#define SENINF1_CSI2_CTRL_TRIO_MUX 0x0A78 > > > > +#define SENINF1_CSI2_CTRL_TRIO_CON 0x0A7C > > > > +#define SENINF1_FIX_ADDR_CPHY0_DBG 0x0A80 > > > > +#define SENINF1_FIX_ADDR_CPHY1_DBG 0x0A84 > > > > +#define SENINF1_FIX_ADDR_CPHY2_DBG 0x0A88 > > > > +#define SENINF1_FIX_ADDR_DBG 0x0A8C > > > > +#define SENINF1_WIRE_STATE_DECODE_CPHY0_DBG0 0x0A90 > > > > +#define SENINF1_WIRE_STATE_DECODE_CPHY0_DBG1 0x0A94 > > > > +#define SENINF1_WIRE_STATE_DECODE_CPHY1_DBG0 0x0A98 > > > > +#define SENINF1_WIRE_STATE_DECODE_CPHY1_DBG1 0x0A9C > > > > +#define SENINF1_WIRE_STATE_DECODE_CPHY2_DBG0 0x0AA0 > > > > +#define SENINF1_WIRE_STATE_DECODE_CPHY2_DBG1 0x0AA4 > > > > +#define SENINF1_SYNC_RESYNC_CTL 0x0AA8 > > > > +#define SENINF1_POST_DETECT_CTL 0x0AAC > > > > +#define SENINF1_WIRE_STATE_DECODE_CONFIG 0x0AB0 > > > > +#define SENINF1_CSI2_CPHY_LNRD_FSM 0x0AB4 > > > > +#define SENINF1_FIX_ADDR_CPHY0_DBG0 0x0AB8 > > > > +#define SENINF1_FIX_ADDR_CPHY0_DBG1 0x0ABC > > > > +#define SENINF1_FIX_ADDR_CPHY0_DBG2 0x0AC0 > > > > +#define SENINF1_FIX_ADDR_CPHY1_DBG0 0x0AC4 > > > > +#define SENINF1_FIX_ADDR_CPHY1_DBG1 0x0AC8 > > > > +#define SENINF1_FIX_ADDR_CPHY1_DBG2 0x0ACC > > > > +#define SENINF1_FIX_ADDR_CPHY2_DBG0 0x0AD0 > > > > +#define SENINF1_FIX_ADDR_CPHY2_DBG1 0x0AD4 > > > > +#define SENINF1_FIX_ADDR_CPHY2_DBG2 0x0AD8 > > > > +#define SENINF1_FIX_ADDR_DBG0 0x0ADC > > > > +#define SENINF1_FIX_ADDR_DBG1 0x0AE0 > > > > +#define SENINF1_FIX_ADDR_DBG2 0x0AE4 > > > > +#define SENINF1_CSI2_MODE 0x0AE8 > > > > +#define rsv_0AEC 0x0AEC > > > > +#define SENINF1_CSI2_DI_EXT 0x0AF0 > > > > +#define SENINF1_CSI2_DI_CTRL_EXT 0x0AF4 > > > > +#define SENINF1_CSI2_CPHY_LOOPBACK 0x0AF8 > > > > +#define rsv_0AFC 0x0AFC > > > > +#define SENINF1_CSI2_PROGSEQ_0 0x0B00 > > > > +#define SENINF1_CSI2_PROGSEQ_1 0x0B04 > > > > +#define rsv_0B08_2 0x0B08 > > > > +#define SENINF1_CSI2_INT_EN_EXT 0x0B10 > > > > +#define SENINF1_CSI2_INT_STATUS_EXT 0x0B14 > > > > +#define SENINF1_CSI2_CPHY_FIX_POINT_RST 0x0B18 > > > > +#define SENINF1_CSI2_RLR3_CON0 0x0B1C > > > > +#define SENINF1_CSI2_DPHY_SYNC 0x0B20 > > > > +#define SENINF1_CSI2_DESKEW_SYNC 0x0B24 > > > > +#define SENINF1_CSI2_DETECT_DBG2 0x0B28 > > > > +#define rsv_0B2C 0x0B2C > > > > +#define SENINF1_FIX_ADDR_CPHY3_DBG0 0x0B30 > > > > +#define SENINF1_FIX_ADDR_CPHY3_DBG1 0x0B34 > > > > +#define SENINF1_FIX_ADDR_CPHY3_DBG2 0x0B38 > > > > +#define SENINF1_CSI2_DI_EXT_2 0x0B3C > > > > +#define SENINF1_CSI2_DI_CTRL_EXT_2 0x0B40 > > > > +#define SENINF1_WIRE_STATE_DECODE_CPHY3_DBG0 0x0B44 > > > > +#define SENINF1_WIRE_STATE_DECODE_CPHY3_DBG1 0x0B48 > > > > +#define rsv_0B4C_109 0x0B4C > > > > +#define SENINF1_MUX_CTRL 0x0D00 > > > > +#define SENINF1_MUX_INTEN 0x0D04 > > > > +#define SENINF1_MUX_INTSTA 0x0D08 > > > > +#define SENINF1_MUX_SIZE 0x0D0C > > > > +#define SENINF1_MUX_DEBUG_1 0x0D10 > > > > +#define SENINF1_MUX_DEBUG_2 0x0D14 > > > > +#define SENINF1_MUX_DEBUG_3 0x0D18 > > > > +#define SENINF1_MUX_DEBUG_4 0x0D1C > > > > +#define SENINF1_MUX_DEBUG_5 0x0D20 > > > > +#define SENINF1_MUX_DEBUG_6 0x0D24 > > > > +#define SENINF1_MUX_DEBUG_7 0x0D28 > > > > +#define SENINF1_MUX_SPARE 0x0D2C > > > > +#define SENINF1_MUX_DATA 0x0D30 > > > > +#define SENINF1_MUX_DATA_CNT 0x0D34 > > > > +#define SENINF1_MUX_CROP 0x0D38 > > > > +#define SENINF1_MUX_CTRL_EXT 0x0D3C > > > > +#define rsv_0D40_240 0x0D40 > > > > +#define SENINF_N3D_B_CTL 0x1100 > > > > +#define SENINF_N3D_B_POS 0x1104 > > > > +#define SENINF_N3D_B_TRIG 0x1108 > > > > +#define SENINF_N3D_B_INT 0x110C > > > > +#define SENINF_N3D_B_CNT0 0x1110 > > > > +#define SENINF_N3D_B_CNT1 0x1114 > > > > +#define SENINF_N3D_B_DBG 0x1118 > > > > +#define SENINF_N3D_B_DIFF_THR 0x111C > > > > +#define SENINF_N3D_B_DIFF_CNT 0x1120 > > > > +#define SENINF_N3D_B_DBG_1 0x1124 > > > > +#define SENINF_N3D_B_VALID_TG_CNT 0x1128 > > > > +#define SENINF_N3D_B_SYNC_A_PERIOD 0x112C > > > > +#define SENINF_N3D_B_SYNC_B_PERIOD 0x1130 > > > > +#define SENINF_N3D_B_SYNC_A_PULSE_LEN 0x1134 > > > > +#define SENINF_N3D_B_SYNC_B_PULSE_LEN 0x1138 > > > > +#define SENINF_N3D_B_SUB_CNT 0x113C > > > > +#define SENINF_N3D_B_VSYNC_CNT 0x1140 > > > > +#define rsv_1144_47 0x1144 > > > > +#define SENINF2_CTRL 0x1200 > > > > +#define SENINF2_CTRL_EXT 0x1204 > > > > +#define SENINF2_ASYNC_CTRL 0x1208 > > > > +#define rsv_120C_253 0x120C > > > > +#define SENINF_TG2_PH_CNT 0x1600 > > > > +#define SENINF_TG2_SEN_CK 0x1604 > > > > +#define SENINF_TG2_TM_CTL 0x1608 > > > > +#define SENINF_TG2_TM_SIZE 0x160C > > > > +#define SENINF_TG2_TM_CLK 0x1610 > > > > +#define SENINF_TG2_TM_STP 0x1614 > > > > +#define rsv_1618_131 0x1618 > > > > +#define MIPI_RX_CON24_CSI1 0x1824 > > > > +#define MIPI_RX_CON28_CSI1 0x1828 > > > > +#define rsv_182C_2 0x182C > > > > +#define MIPI_RX_CON34_CSI1 0x1834 > > > > +#define MIPI_RX_CON38_CSI1 0x1838 > > > > +#define MIPI_RX_CON3C_CSI1 0x183C > > > > +#define rsv_1840_15 0x1840 > > > > +#define MIPI_RX_CON7C_CSI1 0x187C > > > > +#define MIPI_RX_CON80_CSI1 0x1880 > > > > +#define MIPI_RX_CON84_CSI1 0x1884 > > > > +#define MIPI_RX_CON88_CSI1 0x1888 > > > > +#define MIPI_RX_CON8C_CSI1 0x188C > > > > +#define MIPI_RX_CON90_CSI1 0x1890 > > > > +#define MIPI_RX_CON94_CSI1 0x1894 > > > > +#define MIPI_RX_CON98_CSI1 0x1898 > > > > +#define rsv_189C 0x189C > > > > +#define MIPI_RX_CONA0_CSI1 0x18A0 > > > > +#define rsv_18A4_3 0x18A4 > > > > +#define MIPI_RX_CONB0_CSI1 0x18B0 > > > > +#define MIPI_RX_CONB4_CSI1 0x18B4 > > > > +#define MIPI_RX_CONB8_CSI1 0x18B8 > > > > +#define MIPI_RX_CONBC_CSI1 0x18BC > > > > +#define MIPI_RX_CONC0_CSI1 0x18C0 > > > > +#define MIPI_RX_CONC4_CSI1 0x18C4 > > > > +#define MIPI_RX_CONC8_CSI1 0x18C8 > > > > +#define MIPI_RX_CONCC_CSI1 0x18CC > > > > +#define MIPI_RX_COND0_CSI1 0x18D0 > > > > +#define rsv_18D4_75 0x18D4 > > > > +#define SENINF2_CSI2_CTL 0x1A00 > > > > +#define SENINF2_CSI2_LNRC_TIMING 0x1A04 > > > > +#define SENINF2_CSI2_LNRD_TIMING 0x1A08 > > > > +#define SENINF2_CSI2_DPCM 0x1A0C > > > > +#define SENINF2_CSI2_INT_EN 0x1A10 > > > > +#define SENINF2_CSI2_INT_STATUS 0x1A14 > > > > +#define SENINF2_CSI2_DGB_SEL 0x1A18 > > > > +#define SENINF2_CSI2_DBG_PORT 0x1A1C > > > > +#define SENINF2_CSI2_SPARE0 0x1A20 > > > > +#define SENINF2_CSI2_SPARE1 0x1A24 > > > > +#define SENINF2_CSI2_LNRC_FSM 0x1A28 > > > > +#define SENINF2_CSI2_LNRD_FSM 0x1A2C > > > > +#define SENINF2_CSI2_FRAME_LINE_NUM 0x1A30 > > > > +#define SENINF2_CSI2_GENERIC_SHORT 0x1A34 > > > > +#define SENINF2_CSI2_HSRX_DBG 0x1A38 > > > > +#define SENINF2_CSI2_DI 0x1A3C > > > > +#define SENINF2_CSI2_HS_TRAIL 0x1A40 > > > > +#define SENINF2_CSI2_DI_CTRL 0x1A44 > > > > +#define rsv_1A48 0x1A48 > > > > +#define SENINF2_CSI2_DETECT_CON1 0x1A4C > > > > +#define SENINF2_CSI2_DETECT_CON2 0x1A50 > > > > +#define SENINF2_CSI2_DETECT_CON3 0x1A54 > > > > +#define SENINF2_CSI2_RLR0_CON0 0x1A58 > > > > +#define SENINF2_CSI2_RLR1_CON0 0x1A5C > > > > +#define SENINF2_CSI2_RLR2_CON0 0x1A60 > > > > +#define SENINF2_CSI2_RLR_CON0 0x1A64 > > > > +#define SENINF2_CSI2_MUX_CON 0x1A68 > > > > +#define SENINF2_CSI2_DETECT_DBG0 0x1A6C > > > > +#define SENINF2_CSI2_DETECT_DBG1 0x1A70 > > > > +#define SENINF2_CSI2_RESYNC_MERGE_CTL 0x1A74 > > > > +#define SENINF2_CSI2_CTRL_TRIO_MUX 0x1A78 > > > > +#define SENINF2_CSI2_CTRL_TRIO_CON 0x1A7C > > > > +#define SENINF2_FIX_ADDR_CPHY0_DBG 0x1A80 > > > > +#define SENINF2_FIX_ADDR_CPHY1_DBG 0x1A84 > > > > +#define SENINF2_FIX_ADDR_CPHY2_DBG 0x1A88 > > > > +#define SENINF2_FIX_ADDR_DBG 0x1A8C > > > > +#define SENINF2_WIRE_STATE_DECODE_CPHY0_DBG0 0x1A90 > > > > +#define SENINF2_WIRE_STATE_DECODE_CPHY0_DBG1 0x1A94 > > > > +#define SENINF2_WIRE_STATE_DECODE_CPHY1_DBG0 0x1A98 > > > > +#define SENINF2_WIRE_STATE_DECODE_CPHY1_DBG1 0x1A9C > > > > +#define SENINF2_WIRE_STATE_DECODE_CPHY2_DBG0 0x1AA0 > > > > +#define SENINF2_WIRE_STATE_DECODE_CPHY2_DBG1 0x1AA4 > > > > +#define SENINF2_SYNC_RESYNC_CTL 0x1AA8 > > > > +#define SENINF2_POST_DETECT_CTL 0x1AAC > > > > +#define SENINF2_WIRE_STATE_DECODE_CONFIG 0x1AB0 > > > > +#define SENINF2_CSI2_CPHY_LNRD_FSM 0x1AB4 > > > > +#define SENINF2_FIX_ADDR_CPHY0_DBG0 0x1AB8 > > > > +#define SENINF2_FIX_ADDR_CPHY0_DBG1 0x1ABC > > > > +#define SENINF2_FIX_ADDR_CPHY0_DBG2 0x1AC0 > > > > +#define SENINF2_FIX_ADDR_CPHY1_DBG0 0x1AC4 > > > > +#define SENINF2_FIX_ADDR_CPHY1_DBG1 0x1AC8 > > > > +#define SENINF2_FIX_ADDR_CPHY1_DBG2 0x1ACC > > > > +#define SENINF2_FIX_ADDR_CPHY2_DBG0 0x1AD0 > > > > +#define SENINF2_FIX_ADDR_CPHY2_DBG1 0x1AD4 > > > > +#define SENINF2_FIX_ADDR_CPHY2_DBG2 0x1AD8 > > > > +#define SENINF2_FIX_ADDR_DBG0 0x1ADC > > > > +#define SENINF2_FIX_ADDR_DBG1 0x1AE0 > > > > +#define SENINF2_FIX_ADDR_DBG2 0x1AE4 > > > > +#define SENINF2_CSI2_MODE 0x1AE8 > > > > +#define rsv_1AEC 0x1AEC > > > > +#define SENINF2_CSI2_DI_EXT 0x1AF0 > > > > +#define SENINF2_CSI2_DI_CTRL_EXT 0x1AF4 > > > > +#define SENINF2_CSI2_CPHY_LOOPBACK 0x1AF8 > > > > +#define rsv_1AFC 0x1AFC > > > > +#define SENINF2_CSI2_PROGSEQ_0 0x1B00 > > > > +#define SENINF2_CSI2_PROGSEQ_1 0x1B04 > > > > +#define rsv_1B08_2 0x1B08 > > > > +#define SENINF2_CSI2_INT_EN_EXT 0x1B10 > > > > +#define SENINF2_CSI2_INT_STATUS_EXT 0x1B14 > > > > +#define SENINF2_CSI2_CPHY_FIX_POINT_RST 0x1B18 > > > > +#define SENINF2_CSI2_RLR3_CON0 0x1B1C > > > > +#define SENINF2_CSI2_DPHY_SYNC 0x1B20 > > > > +#define SENINF2_CSI2_DESKEW_SYNC 0x1B24 > > > > +#define SENINF2_CSI2_DETECT_DBG2 0x1B28 > > > > +#define rsv_1B2C 0x1B2C > > > > +#define SENINF2_FIX_ADDR_CPHY3_DBG0 0x1B30 > > > > +#define SENINF2_FIX_ADDR_CPHY3_DBG1 0x1B34 > > > > +#define SENINF2_FIX_ADDR_CPHY3_DBG2 0x1B38 > > > > +#define SENINF2_CSI2_DI_EXT_2 0x1B3C > > > > +#define SENINF2_CSI2_DI_CTRL_EXT_2 0x1B40 > > > > +#define SENINF2_WIRE_STATE_DECODE_CPHY3_DBG0 0x1B44 > > > > +#define SENINF2_WIRE_STATE_DECODE_CPHY3_DBG1 0x1B48 > > > > +#define rsv_1B4C_109 0x1B4C > > > > +#define SENINF2_MUX_CTRL 0x1D00 > > > > +#define SENINF2_MUX_INTEN 0x1D04 > > > > +#define SENINF2_MUX_INTSTA 0x1D08 > > > > +#define SENINF2_MUX_SIZE 0x1D0C > > > > +#define SENINF2_MUX_DEBUG_1 0x1D10 > > > > +#define SENINF2_MUX_DEBUG_2 0x1D14 > > > > +#define SENINF2_MUX_DEBUG_3 0x1D18 > > > > +#define SENINF2_MUX_DEBUG_4 0x1D1C > > > > +#define SENINF2_MUX_DEBUG_5 0x1D20 > > > > +#define SENINF2_MUX_DEBUG_6 0x1D24 > > > > +#define SENINF2_MUX_DEBUG_7 0x1D28 > > > > +#define SENINF2_MUX_SPARE 0x1D2C > > > > +#define SENINF2_MUX_DATA 0x1D30 > > > > +#define SENINF2_MUX_DATA_CNT 0x1D34 > > > > +#define SENINF2_MUX_CROP 0x1D38 > > > > +#define SENINF2_MUX_CTRL_EXT 0x1D3C > > > > +#define rsv_1D40_304 0x1D40 > > > > +#define SENINF3_CTRL 0x2200 > > > > +#define SENINF3_CTRL_EXT 0x2204 > > > > +#define SENINF3_ASYNC_CTRL 0x2208 > > > > +#define rsv_220C_253 0x220C > > > > +#define SENINF_TG3_PH_CNT 0x2600 > > > > +#define SENINF_TG3_SEN_CK 0x2604 > > > > +#define SENINF_TG3_TM_CTL 0x2608 > > > > +#define SENINF_TG3_TM_SIZE 0x260C > > > > +#define SENINF_TG3_TM_CLK 0x2610 > > > > +#define SENINF_TG3_TM_STP 0x2614 > > > > +#define rsv_2618_131 0x2618 > > > > +#define MIPI_RX_CON24_CSI2 0x2824 > > > > +#define MIPI_RX_CON28_CSI2 0x2828 > > > > +#define rsv_282C_2 0x282C > > > > +#define MIPI_RX_CON34_CSI2 0x2834 > > > > +#define MIPI_RX_CON38_CSI2 0x2838 > > > > +#define MIPI_RX_CON3C_CSI2 0x283C > > > > +#define rsv_2840_15 0x2840 > > > > +#define MIPI_RX_CON7C_CSI2 0x287C > > > > +#define MIPI_RX_CON80_CSI2 0x2880 > > > > +#define MIPI_RX_CON84_CSI2 0x2884 > > > > +#define MIPI_RX_CON88_CSI2 0x2888 > > > > +#define MIPI_RX_CON8C_CSI2 0x288C > > > > +#define MIPI_RX_CON90_CSI2 0x2890 > > > > +#define MIPI_RX_CON94_CSI2 0x2894 > > > > +#define MIPI_RX_CON98_CSI2 0x2898 > > > > +#define rsv_289C 0x289C > > > > +#define MIPI_RX_CONA0_CSI2 0x28A0 > > > > +#define rsv_28A4_3 0x28A4 > > > > +#define MIPI_RX_CONB0_CSI2 0x28B0 > > > > +#define MIPI_RX_CONB4_CSI2 0x28B4 > > > > +#define MIPI_RX_CONB8_CSI2 0x28B8 > > > > +#define MIPI_RX_CONBC_CSI2 0x28BC > > > > +#define MIPI_RX_CONC0_CSI2 0x28C0 > > > > +#define MIPI_RX_CONC4_CSI2 0x28C4 > > > > +#define MIPI_RX_CONC8_CSI2 0x28C8 > > > > +#define MIPI_RX_CONCC_CSI2 0x28CC > > > > +#define MIPI_RX_COND0_CSI2 0x28D0 > > > > +#define rsv_28D4_75 0x28D4 > > > > +#define SENINF3_CSI2_CTL 0x2A00 > > > > +#define SENINF3_CSI2_LNRC_TIMING 0x2A04 > > > > +#define SENINF3_CSI2_LNRD_TIMING 0x2A08 > > > > +#define SENINF3_CSI2_DPCM 0x2A0C > > > > +#define SENINF3_CSI2_INT_EN 0x2A10 > > > > +#define SENINF3_CSI2_INT_STATUS 0x2A14 > > > > +#define SENINF3_CSI2_DGB_SEL 0x2A18 > > > > +#define SENINF3_CSI2_DBG_PORT 0x2A1C > > > > +#define SENINF3_CSI2_SPARE0 0x2A20 > > > > +#define SENINF3_CSI2_SPARE1 0x2A24 > > > > +#define SENINF3_CSI2_LNRC_FSM 0x2A28 > > > > +#define SENINF3_CSI2_LNRD_FSM 0x2A2C > > > > +#define SENINF3_CSI2_FRAME_LINE_NUM 0x2A30 > > > > +#define SENINF3_CSI2_GENERIC_SHORT 0x2A34 > > > > +#define SENINF3_CSI2_HSRX_DBG 0x2A38 > > > > +#define SENINF3_CSI2_DI 0x2A3C > > > > +#define SENINF3_CSI2_HS_TRAIL 0x2A40 > > > > +#define SENINF3_CSI2_DI_CTRL 0x2A44 > > > > +#define rsv_2A48 0x2A48 > > > > +#define SENINF3_CSI2_DETECT_CON1 0x2A4C > > > > +#define SENINF3_CSI2_DETECT_CON2 0x2A50 > > > > +#define SENINF3_CSI2_DETECT_CON3 0x2A54 > > > > +#define SENINF3_CSI2_RLR0_CON0 0x2A58 > > > > +#define SENINF3_CSI2_RLR1_CON0 0x2A5C > > > > +#define SENINF3_CSI2_RLR2_CON0 0x2A60 > > > > +#define SENINF3_CSI2_RLR_CON0 0x2A64 > > > > +#define SENINF3_CSI2_MUX_CON 0x2A68 > > > > +#define SENINF3_CSI2_DETECT_DBG0 0x2A6C > > > > +#define SENINF3_CSI2_DETECT_DBG1 0x2A70 > > > > +#define SENINF3_CSI2_RESYNC_MERGE_CTL 0x2A74 > > > > +#define SENINF3_CSI2_CTRL_TRIO_MUX 0x2A78 > > > > +#define SENINF3_CSI2_CTRL_TRIO_CON 0x2A7C > > > > +#define SENINF3_FIX_ADDR_CPHY0_DBG 0x2A80 > > > > +#define SENINF3_FIX_ADDR_CPHY1_DBG 0x2A84 > > > > +#define SENINF3_FIX_ADDR_CPHY2_DBG 0x2A88 > > > > +#define SENINF3_FIX_ADDR_DBG 0x2A8C > > > > +#define SENINF3_WIRE_STATE_DECODE_CPHY0_DBG0 0x2A90 > > > > +#define SENINF3_WIRE_STATE_DECODE_CPHY0_DBG1 0x2A94 > > > > +#define SENINF3_WIRE_STATE_DECODE_CPHY1_DBG0 0x2A98 > > > > +#define SENINF3_WIRE_STATE_DECODE_CPHY1_DBG1 0x2A9C > > > > +#define SENINF3_WIRE_STATE_DECODE_CPHY2_DBG0 0x2AA0 > > > > +#define SENINF3_WIRE_STATE_DECODE_CPHY2_DBG1 0x2AA4 > > > > +#define SENINF3_SYNC_RESYNC_CTL 0x2AA8 > > > > +#define SENINF3_POST_DETECT_CTL 0x2AAC > > > > +#define SENINF3_WIRE_STATE_DECODE_CONFIG 0x2AB0 > > > > +#define SENINF3_CSI2_CPHY_LNRD_FSM 0x2AB4 > > > > +#define SENINF3_FIX_ADDR_CPHY0_DBG0 0x2AB8 > > > > +#define SENINF3_FIX_ADDR_CPHY0_DBG1 0x2ABC > > > > +#define SENINF3_FIX_ADDR_CPHY0_DBG2 0x2AC0 > > > > +#define SENINF3_FIX_ADDR_CPHY1_DBG0 0x2AC4 > > > > +#define SENINF3_FIX_ADDR_CPHY1_DBG1 0x2AC8 > > > > +#define SENINF3_FIX_ADDR_CPHY1_DBG2 0x2ACC > > > > +#define SENINF3_FIX_ADDR_CPHY2_DBG0 0x2AD0 > > > > +#define SENINF3_FIX_ADDR_CPHY2_DBG1 0x2AD4 > > > > +#define SENINF3_FIX_ADDR_CPHY2_DBG2 0x2AD8 > > > > +#define SENINF3_FIX_ADDR_DBG0 0x2ADC > > > > +#define SENINF3_FIX_ADDR_DBG1 0x2AE0 > > > > +#define SENINF3_FIX_ADDR_DBG2 0x2AE4 > > > > +#define SENINF3_CSI2_MODE 0x2AE8 > > > > +#define rsv_2AEC 0x2AEC > > > > +#define SENINF3_CSI2_DI_EXT 0x2AF0 > > > > +#define SENINF3_CSI2_DI_CTRL_EXT 0x2AF4 > > > > +#define SENINF3_CSI2_CPHY_LOOPBACK 0x2AF8 > > > > +#define rsv_2AFC 0x2AFC > > > > +#define SENINF3_CSI2_PROGSEQ_0 0x2B00 > > > > +#define SENINF3_CSI2_PROGSEQ_1 0x2B04 > > > > +#define rsv_2B08_2 0x2B08 > > > > +#define SENINF3_CSI2_INT_EN_EXT 0x2B10 > > > > +#define SENINF3_CSI2_INT_STATUS_EXT 0x2B14 > > > > +#define SENINF3_CSI2_CPHY_FIX_POINT_RST 0x2B18 > > > > +#define SENINF3_CSI2_RLR3_CON0 0x2B1C > > > > +#define SENINF3_CSI2_DPHY_SYNC 0x2B20 > > > > +#define SENINF3_CSI2_DESKEW_SYNC 0x2B24 > > > > +#define SENINF3_CSI2_DETECT_DBG2 0x2B28 > > > > +#define rsv_2B2C 0x2B2C > > > > +#define SENINF3_FIX_ADDR_CPHY3_DBG0 0x2B30 > > > > +#define SENINF3_FIX_ADDR_CPHY3_DBG1 0x2B34 > > > > +#define SENINF3_FIX_ADDR_CPHY3_DBG2 0x2B38 > > > > +#define SENINF3_CSI2_DI_EXT_2 0x2B3C > > > > +#define SENINF3_CSI2_DI_CTRL_EXT_2 0x2B40 > > > > +#define SENINF3_WIRE_STATE_DECODE_CPHY3_DBG0 0x2B44 > > > > +#define SENINF3_WIRE_STATE_DECODE_CPHY3_DBG1 0x2B48 > > > > +#define rsv_2B4C_109 0x2B4C > > > > +#define SENINF3_MUX_CTRL 0x2D00 > > > > +#define SENINF3_MUX_INTEN 0x2D04 > > > > +#define SENINF3_MUX_INTSTA 0x2D08 > > > > +#define SENINF3_MUX_SIZE 0x2D0C > > > > +#define SENINF3_MUX_DEBUG_1 0x2D10 > > > > +#define SENINF3_MUX_DEBUG_2 0x2D14 > > > > +#define SENINF3_MUX_DEBUG_3 0x2D18 > > > > +#define SENINF3_MUX_DEBUG_4 0x2D1C > > > > +#define SENINF3_MUX_DEBUG_5 0x2D20 > > > > +#define SENINF3_MUX_DEBUG_6 0x2D24 > > > > +#define SENINF3_MUX_DEBUG_7 0x2D28 > > > > +#define SENINF3_MUX_SPARE 0x2D2C > > > > +#define SENINF3_MUX_DATA 0x2D30 > > > > +#define SENINF3_MUX_DATA_CNT 0x2D34 > > > > +#define SENINF3_MUX_CROP 0x2D38 > > > > +#define SENINF3_MUX_CTRL_EXT 0x2D3C > > > > +#define rsv_2D40_304 0x2D40 > > > > +#define SENINF4_CTRL 0x3200 > > > > +#define SENINF4_CTRL_EXT 0x3204 > > > > +#define SENINF4_ASYNC_CTRL 0x3208 > > > > +#define rsv_320C_253 0x320C > > > > +#define SENINF_TG4_PH_CNT 0x3600 > > > > +#define SENINF_TG4_SEN_CK 0x3604 > > > > +#define SENINF_TG4_TM_CTL 0x3608 > > > > +#define SENINF_TG4_TM_SIZE 0x360C > > > > +#define SENINF_TG4_TM_CLK 0x3610 > > > > +#define SENINF_TG4_TM_STP 0x3614 > > > > +#define rsv_3618_131 0x3618 > > > > +#define MIPI_RX_CON24_CSI3 0x3824 > > > > +#define MIPI_RX_CON28_CSI3 0x3828 > > > > +#define rsv_382C_2 0x382C > > > > +#define MIPI_RX_CON34_CSI3 0x3834 > > > > +#define MIPI_RX_CON38_CSI3 0x3838 > > > > +#define MIPI_RX_CON3C_CSI3 0x383C > > > > +#define rsv_3840_15 0x3840 > > > > +#define MIPI_RX_CON7C_CSI3 0x387C > > > > +#define MIPI_RX_CON80_CSI3 0x3880 > > > > +#define MIPI_RX_CON84_CSI3 0x3884 > > > > +#define MIPI_RX_CON88_CSI3 0x3888 > > > > +#define MIPI_RX_CON8C_CSI3 0x388C > > > > +#define MIPI_RX_CON90_CSI3 0x3890 > > > > +#define MIPI_RX_CON94_CSI3 0x3894 > > > > +#define MIPI_RX_CON98_CSI3 0x3898 > > > > +#define rsv_389C 0x389C > > > > +#define MIPI_RX_CONA0_CSI3 0x38A0 > > > > +#define rsv_38A4_3 0x38A4 > > > > +#define MIPI_RX_CONB0_CSI3 0x38B0 > > > > +#define MIPI_RX_CONB4_CSI3 0x38B4 > > > > +#define MIPI_RX_CONB8_CSI3 0x38B8 > > > > +#define MIPI_RX_CONBC_CSI3 0x38BC > > > > +#define MIPI_RX_CONC0_CSI3 0x38C0 > > > > +#define MIPI_RX_CONC4_CSI3 0x38C4 > > > > +#define MIPI_RX_CONC8_CSI3 0x38C8 > > > > +#define MIPI_RX_CONCC_CSI3 0x38CC > > > > +#define MIPI_RX_COND0_CSI3 0x38D0 > > > > +#define rsv_38D4_75 0x38D4 > > > > +#define SENINF4_CSI2_CTL 0x3A00 > > > > +#define SENINF4_CSI2_LNRC_TIMING 0x3A04 > > > > +#define SENINF4_CSI2_LNRD_TIMING 0x3A08 > > > > +#define SENINF4_CSI2_DPCM 0x3A0C > > > > +#define SENINF4_CSI2_INT_EN 0x3A10 > > > > +#define SENINF4_CSI2_INT_STATUS 0x3A14 > > > > +#define SENINF4_CSI2_DGB_SEL 0x3A18 > > > > +#define SENINF4_CSI2_DBG_PORT 0x3A1C > > > > +#define SENINF4_CSI2_SPARE0 0x3A20 > > > > +#define SENINF4_CSI2_SPARE1 0x3A24 > > > > +#define SENINF4_CSI2_LNRC_FSM 0x3A28 > > > > +#define SENINF4_CSI2_LNRD_FSM 0x3A2C > > > > +#define SENINF4_CSI2_FRAME_LINE_NUM 0x3A30 > > > > +#define SENINF4_CSI2_GENERIC_SHORT 0x3A34 > > > > +#define SENINF4_CSI2_HSRX_DBG 0x3A38 > > > > +#define SENINF4_CSI2_DI 0x3A3C > > > > +#define SENINF4_CSI2_HS_TRAIL 0x3A40 > > > > +#define SENINF4_CSI2_DI_CTRL 0x3A44 > > > > +#define rsv_3A48 0x3A48 > > > > +#define SENINF4_CSI2_DETECT_CON1 0x3A4C > > > > +#define SENINF4_CSI2_DETECT_CON2 0x3A50 > > > > +#define SENINF4_CSI2_DETECT_CON3 0x3A54 > > > > +#define SENINF4_CSI2_RLR0_CON0 0x3A58 > > > > +#define SENINF4_CSI2_RLR1_CON0 0x3A5C > > > > +#define SENINF4_CSI2_RLR2_CON0 0x3A60 > > > > +#define SENINF4_CSI2_RLR_CON0 0x3A64 > > > > +#define SENINF4_CSI2_MUX_CON 0x3A68 > > > > +#define SENINF4_CSI2_DETECT_DBG0 0x3A6C > > > > +#define SENINF4_CSI2_DETECT_DBG1 0x3A70 > > > > +#define SENINF4_CSI2_RESYNC_MERGE_CTL 0x3A74 > > > > +#define SENINF4_CSI2_CTRL_TRIO_MUX 0x3A78 > > > > +#define SENINF4_CSI2_CTRL_TRIO_CON 0x3A7C > > > > +#define SENINF4_FIX_ADDR_CPHY0_DBG 0x3A80 > > > > +#define SENINF4_FIX_ADDR_CPHY1_DBG 0x3A84 > > > > +#define SENINF4_FIX_ADDR_CPHY2_DBG 0x3A88 > > > > +#define SENINF4_FIX_ADDR_DBG 0x3A8C > > > > +#define SENINF4_WIRE_STATE_DECODE_CPHY0_DBG0 0x3A90 > > > > +#define SENINF4_WIRE_STATE_DECODE_CPHY0_DBG1 0x3A94 > > > > +#define SENINF4_WIRE_STATE_DECODE_CPHY1_DBG0 0x3A98 > > > > +#define SENINF4_WIRE_STATE_DECODE_CPHY1_DBG1 0x3A9C > > > > +#define SENINF4_WIRE_STATE_DECODE_CPHY2_DBG0 0x3AA0 > > > > +#define SENINF4_WIRE_STATE_DECODE_CPHY2_DBG1 0x3AA4 > > > > +#define SENINF4_SYNC_RESYNC_CTL 0x3AA8 > > > > +#define SENINF4_POST_DETECT_CTL 0x3AAC > > > > +#define SENINF4_WIRE_STATE_DECODE_CONFIG 0x3AB0 > > > > +#define SENINF4_CSI2_CPHY_LNRD_FSM 0x3AB4 > > > > +#define SENINF4_FIX_ADDR_CPHY0_DBG0 0x3AB8 > > > > +#define SENINF4_FIX_ADDR_CPHY0_DBG1 0x3ABC > > > > +#define SENINF4_FIX_ADDR_CPHY0_DBG2 0x3AC0 > > > > +#define SENINF4_FIX_ADDR_CPHY1_DBG0 0x3AC4 > > > > +#define SENINF4_FIX_ADDR_CPHY1_DBG1 0x3AC8 > > > > +#define SENINF4_FIX_ADDR_CPHY1_DBG2 0x3ACC > > > > +#define SENINF4_FIX_ADDR_CPHY2_DBG0 0x3AD0 > > > > +#define SENINF4_FIX_ADDR_CPHY2_DBG1 0x3AD4 > > > > +#define SENINF4_FIX_ADDR_CPHY2_DBG2 0x3AD8 > > > > +#define SENINF4_FIX_ADDR_DBG0 0x3ADC > > > > +#define SENINF4_FIX_ADDR_DBG1 0x3AE0 > > > > +#define SENINF4_FIX_ADDR_DBG2 0x3AE4 > > > > +#define SENINF4_CSI2_MODE 0x3AE8 > > > > +#define rsv_3AEC 0x3AEC > > > > +#define SENINF4_CSI2_DI_EXT 0x3AF0 > > > > +#define SENINF4_CSI2_DI_CTRL_EXT 0x3AF4 > > > > +#define SENINF4_CSI2_CPHY_LOOPBACK 0x3AF8 > > > > +#define rsv_3AFC 0x3AFC > > > > +#define SENINF4_CSI2_PROGSEQ_0 0x3B00 > > > > +#define SENINF4_CSI2_PROGSEQ_1 0x3B04 > > > > +#define rsv_3B08_2 0x3B08 > > > > +#define SENINF4_CSI2_INT_EN_EXT 0x3B10 > > > > +#define SENINF4_CSI2_INT_STATUS_EXT 0x3B14 > > > > +#define SENINF4_CSI2_CPHY_FIX_POINT_RST 0x3B18 > > > > +#define SENINF4_CSI2_RLR3_CON0 0x3B1C > > > > +#define SENINF4_CSI2_DPHY_SYNC 0x3B20 > > > > +#define SENINF4_CSI2_DESKEW_SYNC 0x3B24 > > > > +#define SENINF4_CSI2_DETECT_DBG2 0x3B28 > > > > +#define rsv_3B2C 0x3B2C > > > > +#define SENINF4_FIX_ADDR_CPHY3_DBG0 0x3B30 > > > > +#define SENINF4_FIX_ADDR_CPHY3_DBG1 0x3B34 > > > > +#define SENINF4_FIX_ADDR_CPHY3_DBG2 0x3B38 > > > > +#define SENINF4_CSI2_DI_EXT_2 0x3B3C > > > > +#define SENINF4_CSI2_DI_CTRL_EXT_2 0x3B40 > > > > +#define SENINF4_WIRE_STATE_DECODE_CPHY3_DBG0 0x3B44 > > > > +#define SENINF4_WIRE_STATE_DECODE_CPHY3_DBG1 0x3B48 > > > > +#define rsv_3B4C_109 0x3B4C > > > > +#define SENINF4_MUX_CTRL 0x3D00 > > > > +#define SENINF4_MUX_INTEN 0x3D04 > > > > +#define SENINF4_MUX_INTSTA 0x3D08 > > > > +#define SENINF4_MUX_SIZE 0x3D0C > > > > +#define SENINF4_MUX_DEBUG_1 0x3D10 > > > > +#define SENINF4_MUX_DEBUG_2 0x3D14 > > > > +#define SENINF4_MUX_DEBUG_3 0x3D18 > > > > +#define SENINF4_MUX_DEBUG_4 0x3D1C > > > > +#define SENINF4_MUX_DEBUG_5 0x3D20 > > > > +#define SENINF4_MUX_DEBUG_6 0x3D24 > > > > +#define SENINF4_MUX_DEBUG_7 0x3D28 > > > > +#define SENINF4_MUX_SPARE 0x3D2C > > > > +#define SENINF4_MUX_DATA 0x3D30 > > > > +#define SENINF4_MUX_DATA_CNT 0x3D34 > > > > +#define SENINF4_MUX_CROP 0x3D38 > > > > +#define SENINF4_MUX_CTRL_EXT 0x3D3C > > > > +#define rsv_3D40_304 0x3D40 > > > > +#define SENINF5_CTRL 0x4200 > > > > +#define SENINF5_CTRL_EXT 0x4204 > > > > +#define SENINF5_ASYNC_CTRL 0x4208 > > > > +#define rsv_420C_253 0x420C > > > > +#define SENINF_TG5_PH_CNT 0x4600 > > > > +#define SENINF_TG5_SEN_CK 0x4604 > > > > +#define SENINF_TG5_TM_CTL 0x4608 > > > > +#define SENINF_TG5_TM_SIZE 0x460C > > > > +#define SENINF_TG5_TM_CLK 0x4610 > > > > +#define SENINF_TG5_TM_STP 0x4614 > > > > +#define rsv_4618_131 0x4618 > > > > +#define MIPI_RX_CON24_CSI4 0x4824 > > > > +#define MIPI_RX_CON28_CSI4 0x4828 > > > > +#define rsv_482C_2 0x482C > > > > +#define MIPI_RX_CON34_CSI4 0x4834 > > > > +#define MIPI_RX_CON38_CSI4 0x4838 > > > > +#define MIPI_RX_CON3C_CSI4 0x483C > > > > +#define rsv_4840_15 0x4840 > > > > +#define MIPI_RX_CON7C_CSI4 0x487C > > > > +#define MIPI_RX_CON80_CSI4 0x4880 > > > > +#define MIPI_RX_CON84_CSI4 0x4884 > > > > +#define MIPI_RX_CON88_CSI4 0x4888 > > > > +#define MIPI_RX_CON8C_CSI4 0x488C > > > > +#define MIPI_RX_CON90_CSI4 0x4890 > > > > +#define MIPI_RX_CON94_CSI4 0x4894 > > > > +#define MIPI_RX_CON98_CSI4 0x4898 > > > > +#define rsv_489C 0x489C > > > > +#define MIPI_RX_CONA0_CSI4 0x48A0 > > > > +#define rsv_48A4_3 0x48A4 > > > > +#define MIPI_RX_CONB0_CSI4 0x48B0 > > > > +#define MIPI_RX_CONB4_CSI4 0x48B4 > > > > +#define MIPI_RX_CONB8_CSI4 0x48B8 > > > > +#define MIPI_RX_CONBC_CSI4 0x48BC > > > > +#define MIPI_RX_CONC0_CSI4 0x48C0 > > > > +#define MIPI_RX_CONC4_CSI4 0x48C4 > > > > +#define MIPI_RX_CONC8_CSI4 0x48C8 > > > > +#define MIPI_RX_CONCC_CSI4 0x48CC > > > > +#define MIPI_RX_COND0_CSI4 0x48D0 > > > > +#define rsv_48D4_75 0x48D4 > > > > +#define SENINF5_CSI2_CTL 0x4A00 > > > > +#define SENINF5_CSI2_LNRC_TIMING 0x4A04 > > > > +#define SENINF5_CSI2_LNRD_TIMING 0x4A08 > > > > +#define SENINF5_CSI2_DPCM 0x4A0C > > > > +#define SENINF5_CSI2_INT_EN 0x4A10 > > > > +#define SENINF5_CSI2_INT_STATUS 0x4A14 > > > > +#define SENINF5_CSI2_DGB_SEL 0x4A18 > > > > +#define SENINF5_CSI2_DBG_PORT 0x4A1C > > > > +#define SENINF5_CSI2_SPARE0 0x4A20 > > > > +#define SENINF5_CSI2_SPARE1 0x4A24 > > > > +#define SENINF5_CSI2_LNRC_FSM 0x4A28 > > > > +#define SENINF5_CSI2_LNRD_FSM 0x4A2C > > > > +#define SENINF5_CSI2_FRAME_LINE_NUM 0x4A30 > > > > +#define SENINF5_CSI2_GENERIC_SHORT 0x4A34 > > > > +#define SENINF5_CSI2_HSRX_DBG 0x4A38 > > > > +#define SENINF5_CSI2_DI 0x4A3C > > > > +#define SENINF5_CSI2_HS_TRAIL 0x4A40 > > > > +#define SENINF5_CSI2_DI_CTRL 0x4A44 > > > > +#define rsv_4A48 0x4A48 > > > > +#define SENINF5_CSI2_DETECT_CON1 0x4A4C > > > > +#define SENINF5_CSI2_DETECT_CON2 0x4A50 > > > > +#define SENINF5_CSI2_DETECT_CON3 0x4A54 > > > > +#define SENINF5_CSI2_RLR0_CON0 0x4A58 > > > > +#define SENINF5_CSI2_RLR1_CON0 0x4A5C > > > > +#define SENINF5_CSI2_RLR2_CON0 0x4A60 > > > > +#define SENINF5_CSI2_RLR_CON0 0x4A64 > > > > +#define SENINF5_CSI2_MUX_CON 0x4A68 > > > > +#define SENINF5_CSI2_DETECT_DBG0 0x4A6C > > > > +#define SENINF5_CSI2_DETECT_DBG1 0x4A70 > > > > +#define SENINF5_CSI2_RESYNC_MERGE_CTL 0x4A74 > > > > +#define SENINF5_CSI2_CTRL_TRIO_MUX 0x4A78 > > > > +#define SENINF5_CSI2_CTRL_TRIO_CON 0x4A7C > > > > +#define SENINF5_FIX_ADDR_CPHY0_DBG 0x4A80 > > > > +#define SENINF5_FIX_ADDR_CPHY1_DBG 0x4A84 > > > > +#define SENINF5_FIX_ADDR_CPHY2_DBG 0x4A88 > > > > +#define SENINF5_FIX_ADDR_DBG 0x4A8C > > > > +#define SENINF5_WIRE_STATE_DECODE_CPHY0_DBG0 0x4A90 > > > > +#define SENINF5_WIRE_STATE_DECODE_CPHY0_DBG1 0x4A94 > > > > +#define SENINF5_WIRE_STATE_DECODE_CPHY1_DBG0 0x4A98 > > > > +#define SENINF5_WIRE_STATE_DECODE_CPHY1_DBG1 0x4A9C > > > > +#define SENINF5_WIRE_STATE_DECODE_CPHY2_DBG0 0x4AA0 > > > > +#define SENINF5_WIRE_STATE_DECODE_CPHY2_DBG1 0x4AA4 > > > > +#define SENINF5_SYNC_RESYNC_CTL 0x4AA8 > > > > +#define SENINF5_POST_DETECT_CTL 0x4AAC > > > > +#define SENINF5_WIRE_STATE_DECODE_CONFIG 0x4AB0 > > > > +#define SENINF5_CSI2_CPHY_LNRD_FSM 0x4AB4 > > > > +#define SENINF5_FIX_ADDR_CPHY0_DBG0 0x4AB8 > > > > +#define SENINF5_FIX_ADDR_CPHY0_DBG1 0x4ABC > > > > +#define SENINF5_FIX_ADDR_CPHY0_DBG2 0x4AC0 > > > > +#define SENINF5_FIX_ADDR_CPHY1_DBG0 0x4AC4 > > > > +#define SENINF5_FIX_ADDR_CPHY1_DBG1 0x4AC8 > > > > +#define SENINF5_FIX_ADDR_CPHY1_DBG2 0x4ACC > > > > +#define SENINF5_FIX_ADDR_CPHY2_DBG0 0x4AD0 > > > > +#define SENINF5_FIX_ADDR_CPHY2_DBG1 0x4AD4 > > > > +#define SENINF5_FIX_ADDR_CPHY2_DBG2 0x4AD8 > > > > +#define SENINF5_FIX_ADDR_DBG0 0x4ADC > > > > +#define SENINF5_FIX_ADDR_DBG1 0x4AE0 > > > > +#define SENINF5_FIX_ADDR_DBG2 0x4AE4 > > > > +#define SENINF5_CSI2_MODE 0x4AE8 > > > > +#define rsv_4AEC 0x4AEC > > > > +#define SENINF5_CSI2_DI_EXT 0x4AF0 > > > > +#define SENINF5_CSI2_DI_CTRL_EXT 0x4AF4 > > > > +#define SENINF5_CSI2_CPHY_LOOPBACK 0x4AF8 > > > > +#define rsv_4AFC 0x4AFC > > > > +#define SENINF5_CSI2_PROGSEQ_0 0x4B00 > > > > +#define SENINF5_CSI2_PROGSEQ_1 0x4B04 > > > > +#define rsv_4B08_2 0x4B08 > > > > +#define SENINF5_CSI2_INT_EN_EXT 0x4B10 > > > > +#define SENINF5_CSI2_INT_STATUS_EXT 0x4B14 > > > > +#define SENINF5_CSI2_CPHY_FIX_POINT_RST 0x4B18 > > > > +#define SENINF5_CSI2_RLR3_CON0 0x4B1C > > > > +#define SENINF5_CSI2_DPHY_SYNC 0x4B20 > > > > +#define SENINF5_CSI2_DESKEW_SYNC 0x4B24 > > > > +#define SENINF5_CSI2_DETECT_DBG2 0x4B28 > > > > +#define rsv_4B2C 0x4B2C > > > > +#define SENINF5_FIX_ADDR_CPHY3_DBG0 0x4B30 > > > > +#define SENINF5_FIX_ADDR_CPHY3_DBG1 0x4B34 > > > > +#define SENINF5_FIX_ADDR_CPHY3_DBG2 0x4B38 > > > > +#define SENINF5_CSI2_DI_EXT_2 0x4B3C > > > > +#define SENINF5_CSI2_DI_CTRL_EXT_2 0x4B40 > > > > +#define SENINF5_WIRE_STATE_DECODE_CPHY3_DBG0 0x4B44 > > > > +#define SENINF5_WIRE_STATE_DECODE_CPHY3_DBG1 0x4B48 > > > > +#define rsv_4B4C_109 0x4B4C > > > > +#define SENINF5_MUX_CTRL 0x4D00 > > > > +#define SENINF5_MUX_INTEN 0x4D04 > > > > +#define SENINF5_MUX_INTSTA 0x4D08 > > > > +#define SENINF5_MUX_SIZE 0x4D0C > > > > +#define SENINF5_MUX_DEBUG_1 0x4D10 > > > > +#define SENINF5_MUX_DEBUG_2 0x4D14 > > > > +#define SENINF5_MUX_DEBUG_3 0x4D18 > > > > +#define SENINF5_MUX_DEBUG_4 0x4D1C > > > > +#define SENINF5_MUX_DEBUG_5 0x4D20 > > > > +#define SENINF5_MUX_DEBUG_6 0x4D24 > > > > +#define SENINF5_MUX_DEBUG_7 0x4D28 > > > > +#define SENINF5_MUX_SPARE 0x4D2C > > > > +#define SENINF5_MUX_DATA 0x4D30 > > > > +#define SENINF5_MUX_DATA_CNT 0x4D34 > > > > +#define SENINF5_MUX_CROP 0x4D38 > > > > +#define SENINF5_MUX_CTRL_EXT 0x4D3C > > > > +#define rsv_4D40_1008 0x4D40 > > > > +#define SENINF6_MUX_CTRL 0x5D00 > > > > +#define SENINF6_MUX_INTEN 0x5D04 > > > > +#define SENINF6_MUX_INTSTA 0x5D08 > > > > +#define SENINF6_MUX_SIZE 0x5D0C > > > > +#define SENINF6_MUX_DEBUG_1 0x5D10 > > > > +#define SENINF6_MUX_DEBUG_2 0x5D14 > > > > +#define SENINF6_MUX_DEBUG_3 0x5D18 > > > > +#define SENINF6_MUX_DEBUG_4 0x5D1C > > > > +#define SENINF6_MUX_DEBUG_5 0x5D20 > > > > +#define SENINF6_MUX_DEBUG_6 0x5D24 > > > > +#define SENINF6_MUX_DEBUG_7 0x5D28 > > > > +#define SENINF6_MUX_SPARE 0x5D2C > > > > +#define SENINF6_MUX_DATA 0x5D30 > > > > +#define SENINF6_MUX_DATA_CNT 0x5D34 > > > > +#define SENINF6_MUX_CROP 0x5D38 > > > > +#define SENINF6_MUX_CTRL_EXT 0x5D3C > > > > +#define rsv_5D40_1008 0x5D40 > > > > +#define SENINF7_MUX_CTRL 0x6D00 > > > > +#define SENINF7_MUX_INTEN 0x6D04 > > > > +#define SENINF7_MUX_INTSTA 0x6D08 > > > > +#define SENINF7_MUX_SIZE 0x6D0C > > > > +#define SENINF7_MUX_DEBUG_1 0x6D10 > > > > +#define SENINF7_MUX_DEBUG_2 0x6D14 > > > > +#define SENINF7_MUX_DEBUG_3 0x6D18 > > > > +#define SENINF7_MUX_DEBUG_4 0x6D1C > > > > +#define SENINF7_MUX_DEBUG_5 0x6D20 > > > > +#define SENINF7_MUX_DEBUG_6 0x6D24 > > > > +#define SENINF7_MUX_DEBUG_7 0x6D28 > > > > +#define SENINF7_MUX_SPARE 0x6D2C > > > > +#define SENINF7_MUX_DATA 0x6D30 > > > > +#define SENINF7_MUX_DATA_CNT 0x6D34 > > > > +#define SENINF7_MUX_CROP 0x6D38 > > > > +#define SENINF7_MUX_CTRL_EXT 0x6D3C > > > > +#define rsv_6D40_1008 0x6D40 > > > > +#define SENINF8_MUX_CTRL 0x7D00 > > > > +#define SENINF8_MUX_INTEN 0x7D04 > > > > +#define SENINF8_MUX_INTSTA 0x7D08 > > > > +#define SENINF8_MUX_SIZE 0x7D0C > > > > +#define SENINF8_MUX_DEBUG_1 0x7D10 > > > > +#define SENINF8_MUX_DEBUG_2 0x7D14 > > > > +#define SENINF8_MUX_DEBUG_3 0x7D18 > > > > +#define SENINF8_MUX_DEBUG_4 0x7D1C > > > > +#define SENINF8_MUX_DEBUG_5 0x7D20 > > > > +#define SENINF8_MUX_DEBUG_6 0x7D24 > > > > +#define SENINF8_MUX_DEBUG_7 0x7D28 > > > > +#define SENINF8_MUX_SPARE 0x7D2C > > > > +#define SENINF8_MUX_DATA 0x7D30 > > > > +#define SENINF8_MUX_DATA_CNT 0x7D34 > > > > +#define SENINF8_MUX_CROP 0x7D38 > > > > +#define SENINF8_MUX_CTRL_EXT 0x7D3C > > > > +#define rsv_7D40_20 0x7D40 > > > > + > > > > +#endif /* _SENINF_REG_H_ */ > > > > -- > > > > 1.9.1 > > > > > > > > Best regards, > > Keiichi > >
