Hi Marco,
On Fri, Mar 01, 2019 at 11:26:48AM +0100, Marco Felsch wrote:
> On 19-02-13 18:57, Jacopo Mondi wrote:
> > Hi Marco,
> > thanks for the patch.
> >
> > I have some comments, which I hope might get the ball rolling...
>
> Hi Jacopo,
>
> thanks for your review and sorry for the late response. My schedule was
> a bit filled.
>
No worries at all
> >
> > On Tue, Dec 18, 2018 at 03:12:38PM +0100, Marco Felsch wrote:
> > > Add corresponding dt-bindings for the Toshiba tc358746 device.
> > >
> > > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>
> > > ---
> > > .../bindings/media/i2c/toshiba,tc358746.txt | 80 +++++++++++++++++++
> > > 1 file changed, 80 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt
> > >
> > > diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt
> > > new file mode 100644
> > > index 000000000000..499733df744a
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt
> > > @@ -0,0 +1,80 @@
> > > +* Toshiba TC358746 Parallel to MIPI CSI2-TX or MIPI CSI2-RX to Parallel Bridge
> > > +
> > > +The Toshiba TC358746 is a bridge that converts a Parallel-in stream to MIPI CSI-2 TX
> >
> > nit:
> > s/is a bridge that/is a bridge device that/
> > or drop is a bridge completely?
>
> You're right, I will drop this statement.
>
> >
> > > +or a MIPI CSI-2 RX stream into a Parallel-out. It is programmable through I2C.
> >
> > From the thin public available datasheet, it seems to support SPI as
> > programming interface, but only when doing Parallel->CSI-2. I would
> > mention that.
>
> You're right, the SPI interface is only supported in that mode.
>
> Should I add something like:
> It is programmable trough I2C and SPI. The SPI interface is only
> supported in parallel-in -> csi-out mode.
>
I would:
"It is programmable through I2C and SPI, with the SPI interface only
available in parallel to CSI-2 conversion mode"
matter of tastes, really up to you :)
> > > +
> > > +Required Properties:
> > > +
> > > +- compatible: should be "toshiba,tc358746"
> > > +- reg: should be <0x0e>
> >
> > nit: s/should/shall
>
> Okay.
>
> > > +- clocks: should contain a phandle link to the reference clock source
> >
> > just "phandle to the reference clock source" ?
>
> Okay.
>
> > > +- clock-names: the clock input is named "refclk".
> >
> > According to the clock bindings this is optional, and since you have
> > a single clock I would drop it.
>
> Yes it's optional, but the device can also act as clock provider (not
> now, patches in my personal queue for rework). So I won't drop it since
> I never linked the generic clock-bindings.
>
As I read the clock bindings documentation, I don't think 'clock-names'
is related to clock provider functionalities, but it is only for
consumers.
Optional properties:
clock-names: List of clock input name strings sorted in the same
order as the clocks property. Consumers drivers
will use clock-names to match clock input names
with clocks specifiers.
If you're going to support clock provider functionalities, you're
likely going to do that thought a clock-output-names property.
Maybe I don't get what you mean here, and that's anyway minor as it's not
wrong to have that property there, it's maybe just redundant.
> > > +
> > > +Optional Properties:
> > > +
> > > +- reset-gpios: gpio phandle GPIO connected to the reset pin
> >
> > would you drop one of the two "gpio" here. Like ": phandle to the GPIO
> > connected to the reset input pin"
>
> Okay.
>
> > > +
> > > +Parallel Endpoint:
> >
> > Here I got confused. The chip supports 2 inputs (parallel and CSI-2)
> > and two outputs (parallel and CSI-2 again). You mention endpoints
> > propery only here, but it seems from the example you want two ports,
> > with one endpoint child-node each.
>
> Nope, the device has one CSI and one Parallel interface. These
> interfaces can be configured as receiver or as transmitter (according to
> the selected mode). I got you but I remember also the discussion with
> Mauro, Hans, Sakari about the TVP5150 ports. The result of that
> discussion was "don't introduce 'virtual' ports". If I got you right
> your Idea will introduce virtual ports too:
>
> /* Parallel */
> port@0{
> port@0 { ... }; /* input case */
> port@1 { ... }; /* output case */
> };
>
> /* CSI */
> port@1{
> port@0 { ... }; /* input case */
> port@1 { ... }; /* output case */
> };
>
Not really, that was more something like
port@0{
parallel-input-endpoint
....
}
port@1{
mipi-input-endpoint
....
}
port@2{
parallel-output-endpoint
....
}
port@3{
mipi-output-endpoint
....
}
As you explained below here, that's a bad idea.
> > Even if the driver does not support CSI-2->Parallel at the moment,
> > bindings should be future-proof, so I would reserve the first two
> > ports for the inputs, and the last two for the output, or, considering
> > that the two input-output combinations are mutually exclusive, provide
> > one "input" port with two optional endpoints, and one "output" port with
> > two optional endpoints.
>
> I wouldn't map the combinations to the device tree since it is the
> hw-abstraction and the signals still routed to the same pads. The only
> difference in the CSI-2->Parallel case is the timing calculation which
> is out of scope for the dt.
>
I see, thanks for explaining. The hardware connections are certainly
the same, so yes, two ports for input and two ports for output is a
bad idea.
Though, you should better describe here you that you want two ports,
one input and one output one, with one optional endpoint describing a
parallel or CSI-2 connection
Do you think something like the following might apply?
Feel free to re-word and use what you think is appropriate:
"The device node must contain two ports children nodes, grouped in a 'ports'
node. The first port describes the input connection, the second one describes
the output one. Each port shall contain one endpoint subnode that connects
to a remote device and specifies the bus type of the input and output
ports. Only one endpoint per port shall be present.
Endpoint properties:
- Parallel endpoints:
- Required properties:
- bus-width:
- Optional properties:
-
- MIPI CSI-2 endpoints:
- Required properties:
- data-lanes:
- Optional properties:
-
" ^ Here you might need to specify properties whose value depends if
the endpoint is input or output, like link-frequencies above that
afaict applies only to output CSI-2 endpoints, not input ones"
Example:
....
tc358746: tc358746@0e {
....
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tc358746_parallel_in: endpoint {
bus-width = <8>;
remote-endpoint = <µn_parallel_out>;
};
};
port@1 {
reg = <1>;
tc358746_mipi2_out: endpoint {
data-lanes = <1 2>;
remote-endpoint = <&mipi_csi2_in>;
};
};
};
};
What I'm not sure about is if you would need to number the endpoints.
I don't think so as only one at the time could be there, but
video-interfaces.txt seems to suggest so:
If a port can be configured to work with more than one remote device on the same
bus, an 'endpoint' child node must be provided for each of them. If more than
one port is present in a device node or there is more than one endpoint at a
port, or port node needs to be associated with a selected hardware interface,
a common scheme using '#address-cells', '#size-cells' and 'reg' properties is
used.
> > In both cases only one input and one output at the time could be
> > described in DT. Up to you, maybe others have different ideas as
> > well...
> >
> > > +
> > > +Required Properties:
> > > +
> > > +- reg: should be <0>
> > > +- bus-width: the data bus width e.g. <8> for eight bit bus, or <16>
> > > + for sixteen bit wide bus.
> >
> > The chip seems to support up to 24 bits of data bus width
>
> You're right, I will change that.
>
> > > +
> > > +MIPI CSI-2 Endpoint:
> > > +
> > > +Required Properties:
> > > +
> > > +- reg: should be <1>
> > > +- data-lanes: should be <1 2 3 4> for four-lane operation,
> > > + or <1 2> for two-lane operation
> > > +- clock-lanes: should be <0>
> >
> > Can this be changed? If the chip does not allow lane re-ordering you
> > could drop this.
>
> Nope it can't. Only the data-lanes can be disabled seperatly so I added
> the data-lanes property to determine that number and for the sake of
> completeness I added the clock-lanes property.
I see, still a required property with a fixed value is not that
necessary.
>
> >
> > > +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
> > > + expressed as a 64-bit big-endian integer. The frequency
> > > + is half of the bps per lane due to DDR transmission.
> >
> > Does the chip supports a limited set of bus frequencies, or are this
> > "hints" ? I admit this property actually puzzles me, so I might got it
> > wrong..
>
> That's not that easy to answer. The user can add different link-freq.
> the driver can choose. This is relevant for the Parallel-in --> CSI-out.
> If the external pclk is to slow (due to dyn. fps change) and the link-freq.
> is to fast the internally pixel buffer throws underrun interrupts. The
> user notice that by green pixel artifacts. If the user adds more
> possible link-freq. the driver will switch to that one wich full fill
> the timings to avoid a fifo underrun.
>
Ah, so the user is expected to specify a set of frequencies the
driver should pick from to handle slower pixel rates, I see. I cannot
tell how this should handle. If nobody else complains, I think it's
fine then :)
Thanks
j
> >
> > Thanks
> > j
>
> Regards,
> Marco
>
> > > +
> > > +Optional Properties:
> > > +
> > > +- clock-noncontinuous: Presence of this boolean property decides whether the
> > > + MIPI CSI-2 clock is continuous or non-continuous.
> > > +
> > > +For further information on the endpoint node properties, see
> > > +Documentation/devicetree/bindings/media/video-interfaces.txt.
> > > +
> > > +Example:
> > > +
> > > +&i2c {
> > > + tc358746: tc358746@0e {
> > > + reg = <0x0e>;
> > > + compatible = "toshiba,tc358746";
> > > + pinctrl-names = "default";
> > > + clocks = <&clk_cam_ref>;
> > > + clock-names = "refclk";
> > > + reset-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
> > > +
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > +
> > > + port@0 {
> > > + reg = <0>;
> > > +
> > > + tc358746_parallel_in: endpoint {
> > > + bus-width = <8>;
> > > + remote-endpoint = <µn_parallel_out>;
> > > + };
> > > + };
> > > +
> > > + port@1 {
> > > + reg = <1>;
> > > +
> > > + tc358746_mipi2_out: endpoint {
> > > + remote-endpoint = <&mipi_csi2_in>;
> > > + data-lanes = <1 2>;
> > > + clock-lanes = <0>;
> > > + clock-noncontinuous;
> > > + link-frequencies = /bits/ 64 <216000000>;
> > > + };
> > > + };
> > > + };
> > > +};
> > > --
> > > 2.19.1
> > >
>
>
>
> --
> Pengutronix e.K. | |
> Industrial Linux Solutions | http://www.pengutronix.de/ |
> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Attachment:
signature.asc
Description: PGP signature
