Hi Tim,
On 1/15/19 1:58 PM, Tim Harvey wrote:
On Wed, Jan 9, 2019 at 10:30 AM Steve Longerbeam <slongerbeam@xxxxxxxxx> wrote:
Also add an example pipeline for unconverted capture with interweave
on SabreAuto.
Cleanup some language in various places in the process.
Signed-off-by: Steve Longerbeam <slongerbeam@xxxxxxxxx>
Reviewed-by: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>
---
Changes since v4:
- Make clear that it is IDMAC channel that does pixel reordering and
interweave, not the CSI. Caught by Philipp Zabel.
Changes since v3:
- none.
Changes since v2:
- expand on idmac interweave behavior in CSI subdev.
- switch second SabreAuto pipeline example to PAL to give
both NTSC and PAL examples.
- Cleanup some language in various places.
---
Documentation/media/v4l-drivers/imx.rst | 103 +++++++++++++++---------
1 file changed, 66 insertions(+), 37 deletions(-)
<snip>
Capture Pipelines
-----------------
@@ -516,10 +522,33 @@ On the SabreAuto, an on-board ADV7180 SD decoder is connected to the
parallel bus input on the internal video mux to IPU1 CSI0.
The following example configures a pipeline to capture from the ADV7180
-video decoder, assuming NTSC 720x480 input signals, with Motion
-Compensated de-interlacing. Pad field types assume the adv7180 outputs
-"interlaced". $outputfmt can be any format supported by the ipu1_ic_prpvf
-entity at its output pad:
+video decoder, assuming NTSC 720x480 input signals, using simple
+interweave (unconverted and without motion compensation). The adv7180
+must output sequential or alternating fields (field type 'seq-bt' for
+NTSC, or 'alternate'):
+
+.. code-block:: none
+
+ # Setup links
+ media-ctl -l "'adv7180 3-0021':0 -> 'ipu1_csi0_mux':1[1]"
+ media-ctl -l "'ipu1_csi0_mux':2 -> 'ipu1_csi0':0[1]"
+ media-ctl -l "'ipu1_csi0':2 -> 'ipu1_csi0 capture':0[1]"
+ # Configure pads
+ media-ctl -V "'adv7180 3-0021':0 [fmt:UYVY2X8/720x480 field:seq-bt]"
+ media-ctl -V "'ipu1_csi0_mux':2 [fmt:UYVY2X8/720x480]"
+ media-ctl -V "'ipu1_csi0':2 [fmt:AYUV32/720x480]"
+ # Configure "ipu1_csi0 capture" interface (assumed at /dev/video4)
+ v4l2-ctl -d4 --set-fmt-video=field=interlaced_bt
+
+Streaming can then begin on /dev/video4. The v4l2-ctl tool can also be
+used to select any supported YUV pixelformat on /dev/video4.
+
Hi Steve,
I'm testing 4.20 with this patchset on top.
I'm on a GW5104 which has an IMX6Q with the adv7180 on ipu1_csi0 like
the SabeAuto example above I can't get the simple interveave example
to work:
media-ctl -r # reset all links
# Setup links (ADV7180 IPU1_CSI0)
media-ctl -l '"adv7180 2-0020":0 -> "ipu1_csi0_mux":1[1]'
media-ctl -l '"ipu1_csi0_mux":2 -> "ipu1_csi0":0[1]'
media-ctl -l '"ipu1_csi0":2 -> "ipu1_csi0 capture":0[1]' # /dev/video4
# Configure pads
media-ctl -V "'adv7180 2-0020':0 [fmt:UYVY2X8/720x480 field:seq-bt]"
media-ctl -V "'ipu1_csi0_mux':2 [fmt:UYVY2X8/720x480]"
media-ctl -V "'ipu1_csi0':0 [fmt:AYUV32/720x480]"
This is the reason. The adv7180 is only allowing to configure alternate
field mode, and thus it reports the field height on the mbus, not the
full frame height. Imx deals with alternate field mode by capturing a
full frame, so the CSI entity sets the output pad height to double the
height.
So the CSI input pad needs to be configured with the field height:
media-ctl -V "'ipu1_csi0':0 [fmt:AYUV32/720x240]"
It should work for you after doing that. And better yet, don't bother
configuring the input pad, because media-ctl will propagate formats from
source to sink pads for you, so it's better to rely on the propagation,
and set the CSI output pad format instead (full frame height at output pad):
media-ctl -V "'ipu1_csi0':2 [fmt:AYUV32/720x480]"
Final note: the imx.rst doc is technically correct even though it is
showing full frame heights being configured at the pads, because it is
expecting the adv7180 has accepted 'seq-bt'. But even the example given
in that doc works for alternate field mode, because the pad heights are
forced to the correct field height for alternate mode.
Steve
# Configure 'ipu1_csi0 capture' interface (/dev/video4)
v4l2-ctl -d4 --set-fmt-video=field=interlaced_bt
# streaming can now begin on the raw capture device node at /dev/video4
v4l2-ctl -d4 --stream-mmap --stream-to=/x.raw --stream-count=1 # capture 1 frame
[ 5547.354460] ipu1_csi0: pipeline start failed with -32
VIDIOC_STREAMON: failed: Broken pipe
Any ideas what is causing this pipeline failure.
+This example configures a pipeline to capture from the ADV7180
+video decoder, assuming PAL 720x576 input signals, with Motion
+Compensated de-interlacing. The adv7180 must output sequential or
+alternating fields (field type 'seq-tb' for PAL, or 'alternate').
+$outputfmt can be any format supported by the ipu1_ic_prpvf entity
+at its output pad:
.. code-block:: none
@@ -531,11 +560,11 @@ entity at its output pad:
media-ctl -l "'ipu1_ic_prp':2 -> 'ipu1_ic_prpvf':0[1]"
media-ctl -l "'ipu1_ic_prpvf':1 -> 'ipu1_ic_prpvf capture':0[1]"
# Configure pads
- media-ctl -V "'adv7180 3-0021':0 [fmt:UYVY2X8/720x480]"
- media-ctl -V "'ipu1_csi0_mux':2 [fmt:UYVY2X8/720x480 field:interlaced]"
- media-ctl -V "'ipu1_csi0':1 [fmt:AYUV32/720x480 field:interlaced]"
- media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x480 field:none]"
- media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x480 field:none]"
+ media-ctl -V "'adv7180 3-0021':0 [fmt:UYVY2X8/720x576 field:seq-tb]"
+ media-ctl -V "'ipu1_csi0_mux':2 [fmt:UYVY2X8/720x576]"
+ media-ctl -V "'ipu1_csi0':1 [fmt:AYUV32/720x576]"
+ media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x576 field:none]"
+ media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x576 field:none]"
media-ctl -V "'ipu1_ic_prpvf':1 [fmt:$outputfmt field:none]"
Streaming can then begin on the capture device node at
The above motion-compensation example pipeline does now work with this
patch series - thanks for addressing this!
Regards,
Tim
