Re: WinTV Radio rev-c121 remote support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, 05 Jan 2010 21:11:59 +0100, Samuel Rakitničan <samuel.rakitnican@xxxxxxxxx> wrote:

Hi,

I have an old bt878 based analog card. It's 'Hauppauge WinTV Radio' model 44914,
rev C121.

I'm trying to workout support for this shipped remote control. I have
tried to add
following lines to bttv-cards.c and bttv-input.c, but that gived
really bad results
(dmesg output is in attachment).


diff -r b6b82258cf5e linux/drivers/media/video/bt8xx/bttv-cards.c
--- a/linux/drivers/media/video/bt8xx/bttv-cards.c Thu Dec 31 19:14:54 2009
-0200
+++ b/linux/drivers/media/video/bt8xx/bttv-cards.c Tue Jan 05 13:25:09 2010
+0100
@@ -491,6 +491,7 @@
                .pll            = PLL_28,
                .tuner_type     = UNSET,
                .tuner_addr     = ADDR_UNSET,
+               .has_remote     = 1,
        },
        [BTTV_BOARD_MIROPRO] = {
                .name           = "MIRO PCTV pro",
diff -r b6b82258cf5e linux/drivers/media/video/bt8xx/bttv-input.c
--- a/linux/drivers/media/video/bt8xx/bttv-input.c Thu Dec 31 19:14:54 2009
-0200
+++ b/linux/drivers/media/video/bt8xx/bttv-input.c Tue Jan 05 13:25:09 2010
+0100
@@ -341,6 +341,12 @@
ir->last_gpio = ir_extract_bits(bttv_gpio_read(&btv->c),
                                                   ir->mask_keycode);
                break;
+       case BTTV_BOARD_HAUPPAUGE878:
+               ir_codes         = &ir_codes_pctv_sedna_table;
+               ir->mask_keycode = 0;
+               ir->mask_keyup   = 0;
+               //ir->polling      = 50;
+               break;
        }
        if (NULL == ir_codes) {
                dprintk(KERN_INFO "Ooops: IR config error [card=%d]\n",
btv->c.type);



root@crni:~/v4l-dvb# modprobe bttv
Segmentation fault
root@crni:~/v4l-dvb#
Message from syslogd@crni at Tue Jan  5 13:03:08 2010 ...
crni kernel: Oops: 0000 [#1] SMP

 [...]




So I guess that's not going to work. I have read in
wiki that Hauppauge cards needs ir-kbd-i2c, so I tried with that too, but
then similar error like previous happens when I try 'modprobe ir-kbd-i2c debug=1
hauppauge=1' as well as just 'modprobe ir-kbd-i2c'.

Can I have a little pointer what to do?

Regards,
Samuel
--
Card: http://linuxtv.org/wiki/index.php/File:Wintv-radio-C121.jpg
Remote: http://linuxtv.org/wiki/index.php/File:Wintv-radio-remote.jpg


Did some investigation, maybe this can help to clarify some things. Still didn't get any response in dmesg from remote.


Chips:
U1 - ST EEPROM - 24C02 4 ST K143L
U2 - Fairchild Dual 4-Channel Analog Multiplexer/Demultiplexer - CD4052BCM
U5 - Microchip EPROM - PIC16C54C 20/S3 0117H08 - IR Remote Control?
U6 - PTC Headphone Driver IC - PT2308-S
In metal can: EPCOS G1984D - demodulator

i2c_scan:
bttv0: i2c scan: found device @ 0x30  [IR (hauppauge)]
bttv0: i2c scan: found device @ 0xa0  [eeprom]
bttv0: i2c scan: found device @ 0xc2  [tuner (analog)]

eeprom dump:
tveeprom 1-0050: full 256-byte eeprom dump:
tveeprom 1-0050: 00: 84 12 00 00 05 50 0e 7f 04 15 01 72 af 91 14 8d
tveeprom 1-0050: 10: 00 00 00 00 05 84 0a 00 01 01 20 77 00 40 62 6c
tveeprom 1-0050: 20: 3c 00 74 02 01 00 02 79 b3 00 00 00 00 00 00 00
tveeprom 1-0050: 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: 70: 00 00 00 00 00 00 00 00 00 00 00 00 13 eb 00 70
tveeprom 1-0050: 80: 84 12 00 00 05 50 0e 7f 04 15 01 72 af 91 14 8d
tveeprom 1-0050: 90: 00 00 00 00 05 84 0a 00 01 01 20 77 00 40 62 6c
tveeprom 1-0050: a0: 3c 00 74 02 01 00 02 79 b3 00 00 00 00 00 00 00
tveeprom 1-0050: b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: f0: 00 00 00 00 00 00 00 00 00 00 00 00 13 eb 00 70
tveeprom 1-0050: Tag [00] + 17 bytes: 05 50 0e 7f 04 15 01 72 af 91 14 8d 00 00 00 00 05
tveeprom 1-0050: Tag [01] + 9 bytes: 01 20 77 00 40 62 6c 3c 00
tveeprom 1-0050: Tag [02] + 3 bytes: 01 00 02

modprobe ir-kbd-i2c debug=1
ir-kbd-i2c: probe 0x1a @ bt878 #0 [sw]: no
ir-kbd-i2c: probe 0x18 @ bt878 #0 [sw]: yes


linux/drivers/media/video/ir-kbd-i2c.c

   417 	case 0x18:
   418 	case 0x1a:
   419 		name        = "Hauppauge";
   420 		//ir->get_key = get_key_haup;
   421 		ir_type     = IR_TYPE_RC5;
   422 		if (hauppauge == 1) {
   423 			ir_codes    = &ir_codes_hauppauge_new_table;
   424 		} else {
   425 			ir_codes    = &ir_codes_rc5_tv_table;
   426 		}
   427 		break;

If I comment above line segfault does not occur. Tried the remote under windows, and is working properly.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux