On Fri, Nov 23, 2018 at 11:51:38AM +0530, Jagan Teki wrote:
> On Wed, Nov 14, 2018 at 8:29 PM Maxime Ripard <maxime.ripard@xxxxxxxxxxx> wrote:
> > From: Mylène Josserand <mylene.josserand@xxxxxxxxxxx>
> >
> > The Nano Pi M1+ comes with an optional sensor based on the ov5640 from
> > Omnivision. Enable the support for it in the DT.
> >
> > Signed-off-by: Mylène Josserand <mylene.josserand@xxxxxxxxxxx>
> > Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxx>
> > ---
> > arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts | 85 +++++++++++++++++++
> > 1 file changed, 85 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
> > index 06010a9afba0..2ac62d109285 100644
> > --- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
> > +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
> > @@ -52,6 +52,37 @@
> > ethernet1 = &sdio_wifi;
> > };
> >
> > + cam_xclk: cam-xclk {
> > + #clock-cells = <0>;
> > + compatible = "fixed-clock";
> > + clock-frequency = <24000000>;
> > + clock-output-names = "cam-xclk";
> > + };
> > +
> > + reg_cam_avdd: cam-avdd {
> > + compatible = "regulator-fixed";
> > + regulator-name = "cam500b-avdd";
> > + regulator-min-microvolt = <2800000>;
> > + regulator-max-microvolt = <2800000>;
> > + vin-supply = <®_vcc3v3>;
> > + };
> > +
> > + reg_cam_dovdd: cam-dovdd {
> > + compatible = "regulator-fixed";
> > + regulator-name = "cam500b-dovdd";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + vin-supply = <®_vcc3v3>;
> > + };
> > +
> > + reg_cam_dvdd: cam-dvdd {
> > + compatible = "regulator-fixed";
> > + regulator-name = "cam500b-dvdd";
> > + regulator-min-microvolt = <1500000>;
> > + regulator-max-microvolt = <1500000>;
> > + vin-supply = <®_vcc3v3>;
> > + };
> > +
> > reg_gmac_3v3: gmac-3v3 {
> > compatible = "regulator-fixed";
> > regulator-name = "gmac-3v3";
> > @@ -69,6 +100,26 @@
> > };
> > };
> >
> > +&csi {
> > + status = "okay";
> > +
> > + port {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + /* Parallel bus endpoint */
> > + csi_from_ov5640: endpoint {
> > + remote-endpoint = <&ov5640_to_csi>;
> > + bus-width = <8>;
> > + data-shift = <2>;
> > + hsync-active = <1>; /* Active high */
> > + vsync-active = <0>; /* Active low */
> > + data-active = <1>; /* Active high */
> > + pclk-sample = <1>; /* Rising */
> > + };
> > + };
> > +};
> > +
> > &ehci1 {
> > status = "okay";
> > };
> > @@ -94,6 +145,40 @@
> > };
> > };
> >
> > +&i2c2 {
> > + status = "okay";
> > +
> > + ov5640: camera@3c {
> > + compatible = "ovti,ov5640";
> > + reg = <0x3c>;
> > + clocks = <&cam_xclk>;
>
> I think we can directly use existing 24MHz oscillator, &osc24M
That's not how the hardware is built, so not really.
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
