On 24-Oct-18 18:40, Rob Herring wrote:
> On Fri, Oct 19, 2018 at 02:52:25PM +0200, Luis Oliveira wrote:
>> Add bindings for Synopsys DesignWare MIPI CSI-2 host.
>>
>> Signed-off-by: Luis Oliveira <lolivei@xxxxxxxxxxxx>
>> ---
>> Changelog
>> v2-V3
>> - removed IPI settings
>>
>> .../devicetree/bindings/media/snps,dw-csi-plat.txt | 52 ++++++++++++++++++++++
>> 1 file changed, 52 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
>>
>> diff --git a/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt b/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
>> new file mode 100644
>> index 0000000..be3da05
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
>> @@ -0,0 +1,52 @@
>> +Synopsys DesignWare CSI-2 Host controller
>> +
>> +Description
>> +-----------
>> +
>> +This HW block is used to receive image coming from an MIPI CSI-2 compatible
>> +camera.
>> +
>> +Required properties:
>> +- compatible: shall be "snps,dw-csi-plat"
>
> 'plat' is really part of the name of the h/w block?
>
It is the name of the platform driver for CSI compatible with this block. Is
that wrong?
>> +- reg : physical base address and size of the device memory mapped
>> + registers;
>> +- interrupts : CSI-2 Host interrupt
>> +- snps,output-type : Core output to be used (IPI-> 0 or IDI->1 or BOTH->2)
>> + These values choose which of the Core outputs will be used,
>> + it can be Image Data Interface or Image Pixel Interface.
>> +- phys : List of one PHY specifier (as defined in
>> + Documentation/devicetree/bindings/phy/phy-bindings.txt).
>> + This PHY is a MIPI DPHY working in RX mode.
>> +- resets : Reference to a reset controller (optional)
>> +
>> +The per-board settings:
>> + - port sub-node describing a single endpoint connected to the camera as
>> + described in video-interfaces.txt[1].
>
> Need to say 2 ports and what is each port? Why no port #0?
>
I will elaborate on that.
>> +
>> +Example:
>> +
>> + csi2_1: csi2@3000 {
>> + compatible = "snps,dw-csi-plat";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = < 0x03000 0x7FF>;
>> + interrupts = <2>;
>> + output-type = <2>;
>> + resets = <&dw_rst 1>;
>> + phys = <&mipi_dphy_rx1 0>;
>> + phy-names = "csi2-dphy";
>
> Not documented. Not really needed for a single entry, so I'd just drop
> it.
>
I will, thanks.
>> +
>> + /* CSI-2 per-board settings */
>> + port@1 {
>> + reg = <1>;
>> + csi1_ep1: endpoint {
>> + remote-endpoint = <&camera_1>;
>> + data-lanes = <1 2>;
>> + };
>> + };
>> + port@2 {
>> + csi1_ep2: endpoint {
>> + remote-endpoint = <&vif1_ep>;
>> + };
>> + };
>> + };
>> --
>> 2.7.4
>>
