On pon, 2009-12-28 at 02:23 +0400, Manu Abraham wrote: > Can you please do a lspci -vn for the Mantis card you have ? Also try > loading the mantis.ko module with verbose=5 module parameter, to get > more debug information. $ lspci -vn 03:07.0 0480: 1822:4e35 (rev 01) Subsystem: 1ae4:0002 Flags: bus master, medium devsel, latency 32, IRQ 21 Memory at fdcff000 (32-bit, prefetchable) [size=4K] Kernel driver in use: Mantis $ modprobe -v mantis verbose=5 insmod /lib/modules/2.6.33-rc1/kernel/drivers/media/dvb/mantis/mantis_core.ko insmod /lib/modules/2.6.33-rc1/kernel/drivers/media/dvb/mantis/mantis.ko verbose=5 $ dmesg [ 2371.762511] Mantis 0000:03:07.0: PCI INT A disabled [ 2462.703393] Mantis 0000:03:07.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 2462.704761] DVB: registering new adapter (Mantis DVB adapter) [ 2463.563234] DVB: registering adapter 0 frontend 0 (Philips TDA10023 DVB-C)... [ 2522.842548] Mantis 0000:03:07.0: PCI INT A disabled [ 2534.495759] found a VP-2040 PCI DVB-C device on (03:07.0), [ 2534.495771] Mantis 0000:03:07.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 2534.495796] Mantis Rev 1 [1ae4:0002], irq: 21, latency: 32 [ 2534.495799] memory: 0x0, mmio: 0xffffc900128cc000 [ 2534.495818] mantis_stream_control (0): Set stream to HIF [ 2534.495841] mantis_i2c_init (0): Initializing I2C .. [ 2534.495845] mantis_i2c_init (0): Disabling I2C interrupt [ 2534.495849] mantis_i2c_xfer (0): Messages:2 [ 2534.495852] mantis_i2c_write: Address=[0x50] <W>[ 08 ] [ 2534.496243] mantis_i2c_read: Address=[0x50] <R>[ 00 08 c9 d0 02 09 ] [ 2534.497049] MAC Address=[00:08:c9:d0:02:09] [ 2534.497051] mantis_dma_init (0): Mantis DMA init [ 2534.497071] mantis_alloc_buffers (0): DMA=0x3d670000 cpu=0xffff88003d670000 size=65536 [ 2534.497073] mantis_alloc_buffers (0): RISC=0x3b731000 cpu=0xffff88003b731000 size=1000 [ 2534.497076] mantis_calc_lines (0): Mantis RISC block bytes=[4096], line bytes=[2048], line count=[32] [ 2534.497077] mantis_dvb_init (0): dvb_register_adapter [ 2534.497079] DVB: registering new adapter (Mantis DVB adapter) [ 2534.497081] mantis_dvb_init (0): dvb_dmx_init [ 2534.497166] mantis_dvb_init (0): dvb_dmxdev_init [ 2534.497269] mantis_frontend_power (0): Power ON [ 2534.497271] gpio_set_bits (0): Set Bit <12> to <1> [ 2534.497274] gpio_set_bits (0): GPIO Value <3000> [ 2534.598099] gpio_set_bits (0): Set Bit <12> to <1> [ 2534.598111] gpio_set_bits (0): GPIO Value <3000> [ 2534.699066] mantis_frontend_soft_reset (0): Frontend RESET [ 2534.699077] gpio_set_bits (0): Set Bit <13> to <0> [ 2534.699085] gpio_set_bits (0): GPIO Value <1000> [ 2534.800077] gpio_set_bits (0): Set Bit <13> to <0> [ 2534.800087] gpio_set_bits (0): GPIO Value <1000> [ 2534.901079] gpio_set_bits (0): Set Bit <13> to <1> [ 2534.901089] gpio_set_bits (0): GPIO Value <3000> [ 2535.002089] gpio_set_bits (0): Set Bit <13> to <1> [ 2535.002099] gpio_set_bits (0): GPIO Value <3000> [ 2535.354084] vp2040_frontend_init (0): Probing for CU1216 (DVB-C) [ 2535.354096] mantis_i2c_xfer (0): Messages:2 [ 2535.354103] mantis_i2c_write: Address=[0x50] <W>[ ff ] [ 2535.354328] mantis_i2c_read: Address=[0x50] <R>[ e4 ] [ 2535.354555] mantis_i2c_xfer (0): Messages:2 [ 2535.354560] mantis_i2c_write: Address=[0x0c] <W>[ 1a ] [ 2535.354781] mantis_i2c_read: Address=[0x0c] <R>[ 7d ] [ 2535.355034] mantis_i2c_xfer (0): Messages:2 [ 2535.355039] mantis_i2c_write: Address=[0x50] <W>[ ff ] [ 2535.355257] mantis_i2c_read: Address=[0x50] <R>[ e4 ] [ 2535.355482] mantis_i2c_xfer (0): Messages:1 [ 2535.355486] mantis_i2c_write: Address=[0x0c] <W>[ 00 33 ] [ 2535.355819] mantis_i2c_xfer (0): Messages:2 [ 2535.355823] mantis_i2c_write: Address=[0x0c] <W>[ 1a ] [ 2535.356055] mantis_i2c_read: Address=[0x0c] <R>[ 7d ] [ 2535.356279] vp2040_frontend_init (0): found Philips CU1216 DVB-C frontend (TDA10023) @ 0x0c [ 2535.356285] vp2040_frontend_init (0): Mantis DVB-C Philips CU1216 frontend attach success [ 2535.356291] vp2040_frontend_init (0): Done! [ 2535.356298] DVB: registering adapter 0 frontend 0 (Philips TDA10023 DVB-C)... [ 2535.356573] mantis_uart_init (0): Initializing UART @ 9600bps parity:NONE [ 2535.356602] mantis_uart_read (0): Reading ... <3f> [ 2535.356609] mantis_uart_work (0): UART BUF:0 <3f> [ 2535.356613] [ 2535.356619] mantis_uart_init (0): UART succesfully initialized -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html