Hi Ricardo,
On Fri, Oct 05, 2018 at 11:57:50PM +0200, Ricardo Ribalda Delgado wrote:
> Document bindings for imx214 camera sensor
>
> Cc: devicetree@xxxxxxxxxxxxxxx
> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@xxxxxxxxx>
> ---
> Changelog from v8:
>
> Rob Herring:
> -rename file
> -Move address to reg
> -rename name on example
> -Patch author
>
> Sakari Ailus:
> -should->shall
>
> .../bindings/media/i2c/sony,imx214.txt | 53 +++++++++++++++++++
> 1 file changed, 53 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx214.txt
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt b/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt
> new file mode 100644
> index 000000000000..2744773070c5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx214.txt
> @@ -0,0 +1,53 @@
> +* Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor
> +
> +The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor with
> +an active array size of 4224H x 3200V. It is programmable through an I2C
> +interface.
> +Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a maximum
> +throughput of 1.2Gbps/lane.
> +
> +
> +Required Properties:
> +- compatible: Shall be "sony,imx214".
> +- reg: I2C bus address of the device. Depending on how the sensor is wired,
> + it shall be <0x10> or <0x1a>;
> +- enable-gpios: GPIO descriptor for the enable pin.
> +- vdddo-supply: Chip digital IO regulator (1.8V).
> +- vdda-supply: Chip analog regulator (2.7V).
> +- vddd-supply: Chip digital core regulator (1.12V).
> +- clocks: Reference to the xclk clock.
> +- clock-names: Shall be "xclk".
It could be that this was already discussed earlier but I missed that ---
clock frequency. Apologies for that. How does the driver know what to ask?
If you expect assigned-clock-rate or such, then I think it should be
explicitly said here.
You also have a single clock, so do you need clock-names?
> +
> +Optional Properties:
> +- flash-leds: See ../video-interfaces.txt
> +- lens-focus: See ../video-interfaces.txt
> +
> +The imx214 device node shall contain one 'port' child node with
> +an 'endpoint' subnode. For further reading on port node refer to
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Required Properties on endpoint:
> +- data-lanes: check ../video-interfaces.txt
> +- link-frequencies: check ../video-interfaces.txt
> +- remote-endpoint: check ../video-interfaces.txt
> +
> +Example:
> +
> + camera-sensor@1a {
> + compatible = "sony,imx214";
> + reg = <0x1a>;
> + vdddo-supply = <&pm8994_lvs1>;
> + vddd-supply = <&camera_vddd_1v12>;
> + vdda-supply = <&pm8994_l17>;
> + lens-focus = <&ad5820>;
> + enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>;
> + clocks = <&mmcc CAMSS_MCLK0_CLK>;
> + clock-names = "xclk";
> + port {
> + imx214_ep: endpoint {
> + data-lanes = <1 2 3 4>;
> + link-frequencies = /bits/ 64 <480000000>;
> + remote-endpoint = <&csiphy0_ep>;
> + };
> + };
> + };
> --
> 2.19.0
>
--
Sakari Ailus
e-mail: sakari.ailus@xxxxxx
