On Mon, Jun 11, 2018 at 01:35:39PM +0200, Luca Ceresoli wrote: > Currently this driver does not support cropping. The supported modes > are the following, all capturing the entire area: > > - 3840x2160, 1:1 binning (native sensor resolution) > - 1920x1080, 2:1 binning > - 1280x720, 3:1 binning > > The VIDIOC_SUBDEV_S_FMT ioctl chooses among these 3 configurations the > one that matches the requested format. > > Add cropping support via VIDIOC_SUBDEV_S_SELECTION: with target > V4L2_SEL_TGT_CROP to choose the captured area, with > V4L2_SEL_TGT_COMPOSE to choose the output resolution. > > To maintain backward compatibility we also allow setting the compose > format via VIDIOC_SUBDEV_S_FMT. To obtain this, compose rect and > output format are computed in the common helper function > __imx274_change_compose(), which sets both to the same width/height > values. > > Cropping also calls __imx274_change_compose() whenever cropping rect > size changes in order to reset the compose rect (and output format > size) for 1:1 binning. > > Also change the names in enum imx274_mode from being resolution-based > to being binning-based (e.g. from IMX274_MODE_1920X1080 to > IMX274_MODE_BINNING_2_1). Without cropping, the two naming are > equivalent. With cropping, the resolution could be different, > e.g. using 2:1 binning mode to crop 1200x960 and output a 600x480 > format. Using binning in the names avoids any misunderstanding. For > the same reason, replace the 'size' field in struct imx274_frmfmt with > 'bin_ratio'. > > Signed-off-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx> > Cc: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx> > > --- > Changed v3 -> v4: > - Set the binning via the SELECTION API (COMPOSE rect), but still > allow using VIDIOC_SUBDEV_S_FMT for backward compatibility. > - rename imx274_set_trimming -> imx274_apply_trimming for clarity > > Changed v2 -> v3: > - Remove hard-coded HMAX reg setting from all modes, not only the > first one. HMAX is always computed and set in s_stream now. > - Reword commit log message. > > Changed v1 -> v2: > - add "media: " prefix to commit message > --- > drivers/media/i2c/imx274.c | 416 +++++++++++++++++++++++++++++++++++---------- > 1 file changed, 326 insertions(+), 90 deletions(-) > > diff --git a/drivers/media/i2c/imx274.c b/drivers/media/i2c/imx274.c > index 2c13961e9764..8bfc20a46b3d 100644 > --- a/drivers/media/i2c/imx274.c > +++ b/drivers/media/i2c/imx274.c > @@ -5,6 +5,7 @@ > * > * Leon Luo <leonl@xxxxxxxxxxxxxxxxxx> > * Edwin Zou <edwinz@xxxxxxxxxxxxxxxxxx> > + * Luca Ceresoli <luca@xxxxxxxxxxxxxxxx> > * > * This program is free software; you can redistribute it and/or modify it > * under the terms and conditions of the GNU General Public License, > @@ -19,6 +20,7 @@ > * along with this program. If not, see <http://www.gnu.org/licenses/>. > */ > > +#include <linux/kernel.h> Alphabetical order, please. > #include <linux/clk.h> > #include <linux/delay.h> > #include <linux/gpio.h> > @@ -74,7 +76,7 @@ > */ > #define IMX274_MIN_EXPOSURE_TIME (4 * 260 / 72) > > -#define IMX274_DEFAULT_MODE IMX274_MODE_3840X2160 > +#define IMX274_DEFAULT_MODE IMX274_MODE_BINNING_OFF > #define IMX274_MAX_WIDTH (3840) > #define IMX274_MAX_HEIGHT (2160) > #define IMX274_MAX_FRAME_RATE (120) > @@ -111,6 +113,20 @@ > #define IMX274_SHR_REG_LSB 0x300C /* SHR */ > #define IMX274_SVR_REG_MSB 0x300F /* SVR */ > #define IMX274_SVR_REG_LSB 0x300E /* SVR */ > +#define IMX274_HTRIM_EN_REG 0x3037 > +#define IMX274_HTRIM_START_REG_LSB 0x3038 > +#define IMX274_HTRIM_START_REG_MSB 0x3039 > +#define IMX274_HTRIM_END_REG_LSB 0x303A > +#define IMX274_HTRIM_END_REG_MSB 0x303B > +#define IMX274_VWIDCUTEN_REG 0x30DD > +#define IMX274_VWIDCUT_REG_LSB 0x30DE > +#define IMX274_VWIDCUT_REG_MSB 0x30DF > +#define IMX274_VWINPOS_REG_LSB 0x30E0 > +#define IMX274_VWINPOS_REG_MSB 0x30E1 > +#define IMX274_WRITE_VSIZE_REG_LSB 0x3130 > +#define IMX274_WRITE_VSIZE_REG_MSB 0x3131 > +#define IMX274_Y_OUT_SIZE_REG_LSB 0x3132 > +#define IMX274_Y_OUT_SIZE_REG_MSB 0x3133 > #define IMX274_VMAX_REG_1 0x30FA /* VMAX, MSB */ > #define IMX274_VMAX_REG_2 0x30F9 /* VMAX */ > #define IMX274_VMAX_REG_3 0x30F8 /* VMAX, LSB */ > @@ -141,9 +157,9 @@ static const struct regmap_config imx274_regmap_config = { > }; > > enum imx274_mode { Is this still an appropriate name? imx274_binning? > - IMX274_MODE_3840X2160, > - IMX274_MODE_1920X1080, > - IMX274_MODE_1280X720, > + IMX274_MODE_BINNING_OFF, > + IMX274_MODE_BINNING_2_1, > + IMX274_MODE_BINNING_3_1, > }; > > /* > @@ -152,8 +168,8 @@ enum imx274_mode { > * These are the values to configure the sensor in one of the > * implemented modes. > * > - * @size: recommended recording pixels > * @init_regs: registers to initialize the mode > + * @bin_ratio: downscale factor (e.g. 3 for 3:1 binning) > * @min_frame_len: Minimum frame length for each mode (see "Frame Rate > * Adjustment (CSI-2)" in the datasheet) > * @min_SHR: Minimum SHR register value (see "Shutter Setting (CSI-2)" in the > @@ -163,8 +179,8 @@ enum imx274_mode { > * in Each Readout Drive Mode (CSI-2)" in the datasheet) > */ > struct imx274_frmfmt { > - struct v4l2_frmsize_discrete size; > const struct reg_8 *init_regs; > + unsigned int bin_ratio; > int min_frame_len; > int min_SHR; > int max_fps; > @@ -215,31 +231,14 @@ static const struct reg_8 imx274_mode1_3840x2160_raw10[] = { > {0x3004, 0x01}, > {0x3005, 0x01}, > {0x3006, 0x00}, > - {0x3007, 0x02}, > + {0x3007, 0xa2}, > > {0x3018, 0xA2}, /* output XVS, HVS */ > > {0x306B, 0x05}, > {0x30E2, 0x01}, > - {0x30F6, 0x07}, /* HMAX, 263 */ > - {0x30F7, 0x01}, /* HMAX */ > - > - {0x30dd, 0x01}, /* crop to 2160 */ > - {0x30de, 0x06}, > - {0x30df, 0x00}, > - {0x30e0, 0x12}, > - {0x30e1, 0x00}, > - {0x3037, 0x01}, /* to crop to 3840 */ > - {0x3038, 0x0c}, > - {0x3039, 0x00}, > - {0x303a, 0x0c}, > - {0x303b, 0x0f}, > > {0x30EE, 0x01}, > - {0x3130, 0x86}, > - {0x3131, 0x08}, > - {0x3132, 0x7E}, > - {0x3133, 0x08}, > {0x3342, 0x0A}, > {0x3343, 0x00}, > {0x3344, 0x16}, > @@ -273,32 +272,14 @@ static const struct reg_8 imx274_mode3_1920x1080_raw10[] = { > {0x3004, 0x02}, > {0x3005, 0x21}, > {0x3006, 0x00}, > - {0x3007, 0x11}, > + {0x3007, 0xb1}, > > {0x3018, 0xA2}, /* output XVS, HVS */ > > {0x306B, 0x05}, > {0x30E2, 0x02}, > > - {0x30F6, 0x04}, /* HMAX, 260 */ > - {0x30F7, 0x01}, /* HMAX */ > - > - {0x30dd, 0x01}, /* to crop to 1920x1080 */ > - {0x30de, 0x05}, > - {0x30df, 0x00}, > - {0x30e0, 0x04}, > - {0x30e1, 0x00}, > - {0x3037, 0x01}, > - {0x3038, 0x0c}, > - {0x3039, 0x00}, > - {0x303a, 0x0c}, > - {0x303b, 0x0f}, > - > {0x30EE, 0x01}, > - {0x3130, 0x4E}, > - {0x3131, 0x04}, > - {0x3132, 0x46}, > - {0x3133, 0x04}, > {0x3342, 0x0A}, > {0x3343, 0x00}, > {0x3344, 0x1A}, > @@ -331,31 +312,14 @@ static const struct reg_8 imx274_mode5_1280x720_raw10[] = { > {0x3004, 0x03}, > {0x3005, 0x31}, > {0x3006, 0x00}, > - {0x3007, 0x09}, > + {0x3007, 0xa9}, > > {0x3018, 0xA2}, /* output XVS, HVS */ > > {0x306B, 0x05}, > {0x30E2, 0x03}, > > - {0x30F6, 0x04}, /* HMAX, 260 */ > - {0x30F7, 0x01}, /* HMAX */ > - > - {0x30DD, 0x01}, > - {0x30DE, 0x07}, > - {0x30DF, 0x00}, > - {0x40E0, 0x04}, > - {0x30E1, 0x00}, > - {0x3030, 0xD4}, > - {0x3031, 0x02}, > - {0x3032, 0xD0}, > - {0x3033, 0x02}, > - > {0x30EE, 0x01}, > - {0x3130, 0xE2}, > - {0x3131, 0x02}, > - {0x3132, 0xDE}, > - {0x3133, 0x02}, > {0x3342, 0x0A}, > {0x3343, 0x00}, > {0x3344, 0x1B}, > @@ -498,7 +462,7 @@ static const struct reg_8 imx274_tp_regs[] = { > static const struct imx274_frmfmt imx274_formats[] = { > { > /* mode 1, 4K */ > - .size = {3840, 2160}, > + .bin_ratio = 1, > .init_regs = imx274_mode1_3840x2160_raw10, > .min_frame_len = 4550, > .min_SHR = 12, > @@ -507,7 +471,7 @@ static const struct imx274_frmfmt imx274_formats[] = { > }, > { > /* mode 3, 1080p */ > - .size = {1920, 1080}, > + .bin_ratio = 2, > .init_regs = imx274_mode3_1920x1080_raw10, > .min_frame_len = 2310, > .min_SHR = 8, > @@ -516,7 +480,7 @@ static const struct imx274_frmfmt imx274_formats[] = { > }, > { > /* mode 5, 720p */ > - .size = {1280, 720}, > + .bin_ratio = 3, > .init_regs = imx274_mode5_1280x720_raw10, > .min_frame_len = 2310, > .min_SHR = 8, > @@ -547,7 +511,10 @@ struct imx274_ctrls { > * @pad: Media pad structure > * @client: Pointer to I2C client > * @ctrls: imx274 control structure > + * @crop: rect to be captured > + * @compose: compose rect, i.e. output resolution > * @format: V4L2 media bus frame format structure > + * (width and height are in sync with the compose rect) > * @frame_rate: V4L2 frame rate structure > * @regmap: Pointer to regmap structure > * @reset_gpio: Pointer to reset gpio > @@ -559,6 +526,8 @@ struct stimx274 { > struct media_pad pad; > struct i2c_client *client; > struct imx274_ctrls ctrls; > + struct v4l2_rect crop; > + struct v4l2_rect compose; > struct v4l2_mbus_framefmt format; > struct v4l2_fract frame_interval; > struct regmap *regmap; > @@ -864,6 +833,80 @@ static int imx274_s_ctrl(struct v4l2_ctrl *ctrl) > } > > /** > + * Helper function to change binning and set both compose and format. > + * > + * We have two entry points to change binning: set_fmt and > + * set_selection(COMPOSE). Both have to compute the new output size > + * and set it in both the compose rect and the frame format size. We > + * also need to do the same things after setting cropping to restore > + * 1:1 binning. > + * > + * This function contains the common code for these three cases, it > + * has many arguments in order to accomodate the needs of all of them. > + * > + * Must be called with imx274->lock locked. > + * > + * @imx274 The device object Colon after the name of the argument. Same below. > + * @cfg The pad config we are editing for TRY requests > + * @which V4L2_SUBDEV_FORMAT_ACTIVE or V4L2_SUBDEV_FORMAT_TRY from the caller > + * @width Input-output parameter: set to the desired width before > + * the call, contains the chosen value after returning successfully > + * @height Input-output parameter for height (see @width) > + */ > +static int __imx274_change_compose(struct stimx274 *imx274, > + struct v4l2_subdev_pad_config *cfg, > + u32 which, > + u32 *width, > + u32 *height) > +{ > + struct device *dev = &imx274->client->dev; > + const struct v4l2_rect *cur_crop; > + struct v4l2_mbus_framefmt *tgt_fmt; > + struct v4l2_rect *tgt_compose; > + unsigned int ratio; /* Binning ratio */ > + > + dev_dbg(dev, "%s: request of %dx%d (%s)\n", > + __func__, *width, *height, > + (which == V4L2_SUBDEV_FORMAT_ACTIVE) ? "ACTIVE" : "TRY"); If these's a need for such debug prints, I think they'd be better added to the framework than individual drivers. > + > + if (which == V4L2_SUBDEV_FORMAT_TRY) { > + cur_crop = &cfg->try_crop; > + tgt_compose = &cfg->try_compose; > + tgt_fmt = &cfg->try_fmt; > + } else { > + cur_crop = &imx274->crop; > + tgt_compose = &imx274->compose; > + tgt_fmt = &imx274->format; > + } > + > + /* Find ratio (maximize output resolution). Fallback to 1:1. */ > + for (ratio = 3; ratio > 1; ratio--) > + if (*width <= DIV_ROUND_UP(cur_crop->width, ratio) && > + *height <= DIV_ROUND_UP(cur_crop->height, ratio)) > + break; There are flags to direct the rounding behaviour. The default is the nearest: <URL:https://hverkuil.home.xs4all.nl/spec/uapi/v4l/v4l2-selection-flags.html> The smiapp driver (as the only sensor driver) supports them. > + > + *width = cur_crop->width / ratio; > + *height = cur_crop->height / ratio; > + > + if (which == V4L2_SUBDEV_FORMAT_ACTIVE) > + imx274->mode = &imx274_formats[ratio - 1]; > + > + dev_dbg(dev, "%s: adjusted to %dx%d (%d:1 binning)\n", > + __func__, *width, *height, ratio); Could be here, for binning. %d -> %u --- it's unsigned. > + > + tgt_compose->top = 0; > + tgt_compose->left = 0; > + tgt_compose->width = *width; > + tgt_compose->height = *height; > + > + tgt_fmt->width = *width; > + tgt_fmt->height = *height; > + tgt_fmt->field = V4L2_FIELD_NONE; > + > + return 0; > +} > + > +/** > * imx274_get_fmt - Get the pad format > * @sd: Pointer to V4L2 Sub device structure > * @cfg: Pointer to sub device pad information structure > @@ -901,45 +944,228 @@ static int imx274_set_fmt(struct v4l2_subdev *sd, > { > struct v4l2_mbus_framefmt *fmt = &format->format; > struct stimx274 *imx274 = to_imx274(sd); > - struct i2c_client *client = imx274->client; > - int index; > - > - dev_dbg(&client->dev, > - "%s: width = %d height = %d code = %d\n", > - __func__, fmt->width, fmt->height, fmt->code); > + int err = 0; > > mutex_lock(&imx274->lock); > > - for (index = 0; index < ARRAY_SIZE(imx274_formats); index++) { > - if (imx274_formats[index].size.width == fmt->width && > - imx274_formats[index].size.height == fmt->height) > - break; > - } > - > - if (index >= ARRAY_SIZE(imx274_formats)) { > - /* default to first format */ > - index = 0; > - } > + err = __imx274_change_compose(imx274, cfg, format->which, > + &fmt->width, &fmt->height); > > - imx274->mode = &imx274_formats[index]; > + if (err) > + goto out; > > - if (fmt->width > IMX274_MAX_WIDTH) > - fmt->width = IMX274_MAX_WIDTH; > - if (fmt->height > IMX274_MAX_HEIGHT) > - fmt->height = IMX274_MAX_HEIGHT; > - fmt->width = fmt->width & (~IMX274_MASK_LSB_2_BITS); > - fmt->height = fmt->height & (~IMX274_MASK_LSB_2_BITS); > + /* > + * __imx274_change_compose already set width and height in the > + * applicable format, but we need to keep all other format > + * values, so do a full copy here > + */ > fmt->field = V4L2_FIELD_NONE; > - > if (format->which == V4L2_SUBDEV_FORMAT_TRY) > cfg->try_fmt = *fmt; > else > imx274->format = *fmt; > > +out: > mutex_unlock(&imx274->lock); > + > + return err; > +} > + > +static int imx274_get_selection(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_selection *sel) > +{ > + struct stimx274 *imx274 = to_imx274(sd); > + const struct v4l2_rect *src_crop; > + const struct v4l2_rect *src_compose; > + int ret = 0; > + > + if (sel->pad != 0) > + return -EINVAL; > + > + if (sel->target == V4L2_SEL_TGT_CROP_BOUNDS) { > + sel->r.left = 0; > + sel->r.top = 0; > + sel->r.width = IMX274_MAX_WIDTH; > + sel->r.height = IMX274_MAX_HEIGHT; > + return 0; > + } > + > + if (sel->which == V4L2_SUBDEV_FORMAT_TRY) { > + src_crop = &cfg->try_crop; > + src_compose = &cfg->try_compose; > + } else { > + src_crop = &imx274->crop; > + src_compose = &imx274->compose; > + } > + > + mutex_lock(&imx274->lock); > + > + switch (sel->target) { > + case V4L2_SEL_TGT_CROP: > + sel->r = *src_crop; > + break; > + case V4L2_SEL_TGT_COMPOSE_BOUNDS: > + sel->r.top = 0; > + sel->r.left = 0; > + sel->r.width = src_crop->width; > + sel->r.height = src_crop->height; > + break; > + case V4L2_SEL_TGT_COMPOSE: > + sel->r = *src_compose; > + break; > + default: > + ret = -EINVAL; > + } > + > + mutex_unlock(&imx274->lock); > + > + return ret; > +} > + > +static int imx274_set_selection_crop(struct stimx274 *imx274, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_selection *sel) > +{ > + struct device *dev = &imx274->client->dev; > + struct v4l2_rect *tgt_crop; > + struct v4l2_rect new_crop; > + bool size_changed; > + > + /* > + * h_step could be 12 or 24 depending on the binning. But we > + * won't know the binning until we choose the mode later in > + * imx274_set_fmt(). Thus let's be safe and use the most > + * conservative value in all cases. > + */ > + const int h_step = 24; > + > + dev_dbg(dev, "%s: request of (%d,%d)%dx%d (%s)\n", __func__, > + sel->r.left, sel->r.top, sel->r.width, sel->r.height, > + V4L2_SUBDEV_FORMAT_ACTIVE ? "ACTIVE" : "TRY"); > + > + new_crop.width = rounddown(min_t(u32, sel->r.width, IMX274_MAX_WIDTH), > + h_step); > + > + /* Constraint: HTRIMMING_END - HTRIMMING_START >= 144 */ > + if (new_crop.width < 144) > + new_crop.width = 144; > + > + new_crop.left = min_t(u32, roundup(sel->r.left, h_step), > + IMX274_MAX_WIDTH - new_crop.width); > + > + new_crop.height = > + ALIGN(min_t(u32, sel->r.height, IMX274_MAX_HEIGHT), 2); > + > + new_crop.top = min_t(u32, ALIGN(sel->r.top, 2), > + IMX274_MAX_HEIGHT - new_crop.height); > + > + dev_dbg(dev, "%s: adjusted to (%d,%d)%dx%d", __func__, > + new_crop.left, new_crop.top, new_crop.width, new_crop.height); > + > + sel->r = new_crop; > + > + if (sel->which == V4L2_SUBDEV_FORMAT_TRY) > + tgt_crop = &cfg->try_crop; > + else > + tgt_crop = &imx274->crop; > + > + mutex_lock(&imx274->lock); > + > + size_changed = (new_crop.width != tgt_crop->width || > + new_crop.height != tgt_crop->height); > + > + /* __imx274_change_compose needs the new size in *tgt_crop */ > + *tgt_crop = new_crop; > + > + /* if crop size changed then reset the output image size */ > + if (size_changed) > + __imx274_change_compose(imx274, cfg, sel->which, > + &new_crop.width, &new_crop.height); > + > + mutex_unlock(&imx274->lock); > + > return 0; > } > > +static int imx274_set_selection(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_selection *sel) > +{ > + struct stimx274 *imx274 = to_imx274(sd); > + > + if (sel->pad != 0) > + return -EINVAL; > + > + if (sel->target == V4L2_SEL_TGT_CROP) > + return imx274_set_selection_crop(imx274, cfg, sel); > + > + if (sel->target == V4L2_SEL_TGT_COMPOSE) { > + int err; > + > + mutex_lock(&imx274->lock); > + > + err = __imx274_change_compose(imx274, cfg, sel->which, > + &sel->r.width, &sel->r.height); > + /* > + * __imx274_change_compose already set width and > + * height in set->r, we still need to set top-left > + */ > + if (!err) { > + sel->r.top = 0; > + sel->r.left = 0; > + } > + > + mutex_unlock(&imx274->lock); > + > + return err; > + } > + > + return -EINVAL; > +} > + > +static int imx274_apply_trimming(struct stimx274 *imx274) > +{ > + u32 h_start; > + u32 h_end; > + u32 hmax; > + u32 v_cut; > + s32 v_pos; > + u32 write_v_size; > + u32 y_out_size; > + struct reg_8 regs[17]; > + > + h_start = imx274->crop.left + 12; > + h_end = h_start + imx274->crop.width; > + > + /* Use the minimum allowed value of HMAX */ > + /* Note: except in mode 1, (width / 16 + 23) is always < hmax_min */ > + /* Note: 260 is the minimum HMAX in all implemented modes */ > + hmax = max_t(u32, 260, (imx274->crop.width) / 16 + 23); > + > + /* invert v_pos if VFLIP */ > + v_pos = imx274->ctrls.vflip->cur.val ? > + (-imx274->crop.top / 2) : (imx274->crop.top / 2); > + v_cut = (IMX274_MAX_HEIGHT - imx274->crop.height) / 2; > + write_v_size = imx274->crop.height + 22; > + y_out_size = imx274->crop.height + 14; > + > + prepare_reg(®s[0], IMX274_HMAX_REG_LSB, hmax, 16); > + prepare_reg(®s[2], IMX274_HTRIM_EN_REG, 1, 1); > + prepare_reg(®s[3], IMX274_HTRIM_START_REG_LSB, h_start, 13); > + prepare_reg(®s[5], IMX274_HTRIM_END_REG_LSB, h_end, 13); > + > + prepare_reg(®s[7], IMX274_VWIDCUTEN_REG, 1, 1); > + prepare_reg(®s[8], IMX274_VWIDCUT_REG_LSB, v_cut, 11); > + prepare_reg(®s[10], IMX274_VWINPOS_REG_LSB, v_pos, 12); > + prepare_reg(®s[12], IMX274_WRITE_VSIZE_REG_LSB, write_v_size, 13); > + prepare_reg(®s[14], IMX274_Y_OUT_SIZE_REG_LSB, y_out_size, 13); > + > + regs[16].addr = IMX274_TABLE_END; > + > + return imx274_write_table(imx274, regs); > +} > + > /** > * imx274_g_frame_interval - Get the frame interval > * @sd: Pointer to V4L2 Sub device structure > @@ -1080,6 +1306,10 @@ static int imx274_s_stream(struct v4l2_subdev *sd, int on) > if (ret) > goto fail; > > + ret = imx274_apply_trimming(imx274); > + if (ret) > + goto fail; > + > /* > * update frame rate & expsoure. if the last mode is different, > * HMAX could be changed. As the result, frame rate & exposure > @@ -1589,6 +1819,8 @@ static int imx274_set_frame_interval(struct stimx274 *priv, > static const struct v4l2_subdev_pad_ops imx274_pad_ops = { > .get_fmt = imx274_get_fmt, > .set_fmt = imx274_set_fmt, > + .get_selection = imx274_get_selection, > + .set_selection = imx274_set_selection, > }; > > static const struct v4l2_subdev_video_ops imx274_video_ops = { > @@ -1634,8 +1866,12 @@ static int imx274_probe(struct i2c_client *client, > > /* initialize format */ > imx274->mode = &imx274_formats[IMX274_DEFAULT_MODE]; > - imx274->format.width = imx274->mode->size.width; > - imx274->format.height = imx274->mode->size.height; > + imx274->crop.width = IMX274_MAX_WIDTH; > + imx274->crop.height = IMX274_MAX_HEIGHT; > + imx274->compose.width = imx274->crop.width / imx274->mode->bin_ratio; > + imx274->compose.height = imx274->crop.height / imx274->mode->bin_ratio; > + imx274->format.width = imx274->compose.width; > + imx274->format.height = imx274->compose.height; > imx274->format.field = V4L2_FIELD_NONE; > imx274->format.code = MEDIA_BUS_FMT_SRGGB10_1X10; > imx274->format.colorspace = V4L2_COLORSPACE_SRGB; > -- > 2.7.4 > -- Sakari Ailus sakari.ailus@xxxxxxxxxxxxxxx
