Steve Longerbeam <slongerbeam@xxxxxxxxx> writes:
> Sorry I did find a bug. Please try this patch:
Ok, your patch fixes the first problem (sets the CSI interlaced mode
on input when field = NOE is requested on output). Posting in full since
your mail came somehow mangled with UTF-8.
--- a/drivers/staging/media/imx/imx-media-csi.c
+++ b/drivers/staging/media/imx/imx-media-csi.c
@@ -629,7 +629,6 @@ static int csi_setup(struct csi_priv *priv)
{
struct v4l2_mbus_framefmt *infmt, *outfmt;
struct v4l2_mbus_config mbus_cfg;
- struct v4l2_mbus_framefmt if_fmt;
infmt = &priv->format_mbus[CSI_SINK_PAD];
outfmt = &priv->format_mbus[priv->active_output_pad];
@@ -640,20 +639,13 @@ static int csi_setup(struct csi_priv *priv)
priv->upstream_ep.bus.mipi_csi2.flags :
priv->upstream_ep.bus.parallel.flags;
- /*
- * we need to pass input frame to CSI interface, but
- * with translated field type from output format
- */
- if_fmt = *infmt;
- if_fmt.field = outfmt->field;
-
ipu_csi_set_window(priv->csi, &priv->crop);
ipu_csi_set_downsize(priv->csi,
priv->crop.width == 2 * priv->compose.width,
priv->crop.height == 2 * priv->compose.height);
- ipu_csi_init_interface(priv->csi, &mbus_cfg, &if_fmt);
+ ipu_csi_init_interface(priv->csi, &mbus_cfg, infmt);
ipu_csi_set_dest(priv->csi, priv->dest);
> (the removed code was meant to deal with field type at sink pad being
> "alternate", which ipu_csi_init_interface() doesn't currently recognize, but
> that should be dealt with in IPUv3 driver).
I see.
> With that you should be able to set pad ipu2_csi1:2 to field type
> "none", e.g.
> set pipeline to:
>
> media-ctl -V '"adv7180 2-0020":0[fmt:UYVY2X8 720x480 field:interlaced]'
> media-ctl -V '"ipu2_csi1_mux":1[fmt:UYVY2X8 720x480 field:interlaced]'
> media-ctl -V '"ipu2_csi1_mux":2[fmt:UYVY2X8 720x480 field:interlaced]'
> media-ctl -V '"ipu2_csi1":0[fmt:UYVY2X8 720x480 field:interlaced]'
> media-ctl -V '"ipu2_csi1":2[fmt:UYVY2X8 720x480 field:none]'
>
> With the above patch, capture from ipu1_csi0:2 is fixed for me on
> SabreAuto.
Right, it also works fine for me on Ventana GW5300 (with
ipu_cpmem_skip_odd_chroma_rows() removed as well, of course).
> You may also want to try adding a ~500 msec delay after adv7180 power on
> as I explained earlier:
Ok. In fact I don't have a sync problem even without it, the rolling
image always eventually syncs. Maybe I'll investigate the data stream
(from ADV7180 to CSI) and see what's on. I't a bit complicated since
what I have is just an oscilloscope.
--
Krzysztof Halasa
Industrial Research Institute for Automation and Measurements PIAP
Al. Jerozolimskie 202, 02-486 Warsaw, Poland
