Hi Niklas,
Thank you for the patch.
On Wednesday, 25 April 2018 02:56:52 EEST Niklas Söderlund wrote:
> The VIN Gen3 hardware don't have Line Post-Clip capabilities as VIN Gen2
> hardware have. To protect against writing outside the capture window
> enable field toggle after a set number of lines have been captured.
>
> Capturing outside the allocated capture buffer where observed on R-Car
s/Capturing/Capture/
s/where/has been/
> Gen3 Salvator-XS H3 from the CVBS input if the standard is
> misconfigured. That is if a PAL source is connected to the system but
> the adv748x standard is set to NTSC. In this case the format reported by
> the adv748x is 720x480 and that is what is used for the media pipeline.
> The PAL source generates frames in the format of 720x576 and the field
> is not toggled until the VSYNC is detected and at that time data have
> already been written outside the allocated capture buffer.
>
> With this change the capture in the situation described above results in
> garbage frames but that is far better then writing outside the capture
s/then/than/
> buffer.
>
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> ---
> drivers/media/platform/rcar-vin/rcar-dma.c | 20 +++++++++++++++-----
> 1 file changed, 15 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/media/platform/rcar-vin/rcar-dma.c
> b/drivers/media/platform/rcar-vin/rcar-dma.c index
> ac07f99e3516a620..b41ba9a4a2b3ac90 100644
> --- a/drivers/media/platform/rcar-vin/rcar-dma.c
> +++ b/drivers/media/platform/rcar-vin/rcar-dma.c
> @@ -124,7 +124,9 @@
> #define VNDMR2_VPS (1 << 30)
> #define VNDMR2_HPS (1 << 29)
> #define VNDMR2_FTEV (1 << 17)
> +#define VNDMR2_FTEH (1 << 16)
> #define VNDMR2_VLV(n) ((n & 0xf) << 12)
> +#define VNDMR2_HLV(n) ((n) & 0xfff)
>
> /* Video n CSI2 Interface Mode Register (Gen3) */
> #define VNCSI_IFMD_DES1 (1 << 26)
> @@ -612,8 +614,9 @@ void rvin_crop_scale_comp(struct rvin_dev *vin)
>
> static int rvin_setup(struct rvin_dev *vin)
> {
> - u32 vnmc, dmr, dmr2, interrupts;
> + u32 vnmc, dmr, dmr2, interrupts, lines;
> bool progressive = false, output_is_yuv = false, input_is_yuv = false;
> + bool halfsize = false;
>
> switch (vin->format.field) {
> case V4L2_FIELD_TOP:
> @@ -628,12 +631,15 @@ static int rvin_setup(struct rvin_dev *vin)
> /* Use BT if video standard can be read and is 60 Hz format */
> if (!vin->info->use_mc && vin->std & V4L2_STD_525_60)
> vnmc = VNMC_IM_FULL | VNMC_FOC;
> + halfsize = true;
> break;
> case V4L2_FIELD_INTERLACED_TB:
> vnmc = VNMC_IM_FULL;
> + halfsize = true;
> break;
> case V4L2_FIELD_INTERLACED_BT:
> vnmc = VNMC_IM_FULL | VNMC_FOC;
> + halfsize = true;
> break;
> case V4L2_FIELD_NONE:
> vnmc = VNMC_IM_ODD_EVEN;
> @@ -676,11 +682,15 @@ static int rvin_setup(struct rvin_dev *vin)
> break;
> }
>
> - /* Enable VSYNC Field Toogle mode after one VSYNC input */
> - if (vin->info->model == RCAR_GEN3)
> - dmr2 = VNDMR2_FTEV;
> - else
> + if (vin->info->model == RCAR_GEN3) {
> + /* Enable HSYNC Field Toggle mode after height HSYNC inputs. */
> + lines = vin->format.height / (halfsize ? 2 : 1);
> + dmr2 = VNDMR2_FTEH | VNDMR2_HLV(lines);
> + vin_dbg(vin, "Field Toogle after %u lines\n", lines);
> + } else {
> + /* Enable VSYNC Field Toogle mode after one VSYNC input. */
> dmr2 = VNDMR2_FTEV | VNDMR2_VLV(1);
> + }
>
> /* Hsync Signal Polarity Select */
> if (!(vin->mbus_cfg.flags & V4L2_MBUS_HSYNC_ACTIVE_LOW))
--
Regards,
Laurent Pinchart
