Hi Jacopo,
On Monday, 23 April 2018 10:35:04 EEST jacopo mondi wrote:
> On Sun, Apr 22, 2018 at 10:02:41PM +0200, Peter Rosin wrote:
> > On 2018-04-19 11:31, Jacopo Mondi wrote:
> >> The THC63LVD1024 LVDS to RGB bridge supports two different input mapping
> >> modes, selectable by means of an external pin.
> >>
> >> Describe the LVDS mode map through a newly defined mandatory property in
> >> device tree bindings.
> >>
> >> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> >> ---
> >>
> >> .../devicetree/bindings/display/bridge/thine,thc63lvd1024.txt | 3 +++
> >> 1 file changed, 3 insertions(+)
> >>
> >> diff --git
> >> a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >> b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >> index 37f0c04..0937595 100644
> >> ---
> >> a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >> +++
> >> b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >> @@ -12,6 +12,8 @@ Required properties:
> >> - compatible: Shall be "thine,thc63lvd1024"
> >> - vcc-supply: Power supply for TTL output, TTL CLOCKOUT signal, LVDS
> >> input,
> >> PPL and digital circuitry
> >>
> >> +- thine,map: LVDS mapping mode selection signal, pin name "MAP". Shall
> >> be <1>
> >> + for mapping mode 1, <0> for mapping mode 2
> >
> > Since the MAP pin is an input pin, I would expect there to be an optional
> > gpio specifier like thine,map-gpios so that the driver can set it
> > according to the value given in thine,map in case the HW has a line from
> > some gpio output to the MAP pin (instead of hardwired hi/low which seem
> > to be your thinking).
>
> I see... As the only use case I had has the pin tied to vcc, I
> thought about making it a binary property, and I wonder in how many
> cases the chip 'MAP' pin would actually be GPIO controlled input and
> not an hardwired one instead. I don't see the LVDS mapping mode to be
> changed at runtime, but you are right, who knows....
>
> Do you think we can add an options 'thine,map-gpios' property along
> to the proposed ones?
If the MAP pin is connected to an SoC-controlled GPIO for a given platform
then we will likely need a thine,map-gpios property to control the pin. I
think we can leave it out for now and add it later if the need arises.
The thine,map property serves a different purpose, it indicates the level of
the MAP pin for platforms where the pin is hardwired. If we later introduce a
thine,map-gpios property it should be mutually exclusive with the thine,map
property. The level of the MAP pin should be then software-controlled, not set
through DT.
> >> Optional properties:
> >> - powerdown-gpios: Power down GPIO signal, pin name "/PDWN". Active low
> >>
> >> @@ -36,6 +38,7 @@ Example:
> >> vcc-supply = <®_lvds_vcc>;
> >> powerdown-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
> >> + thine,map = <1>;
> >>
> >> ports {
> >> #address-cells = <1>;
--
Regards,
Laurent Pinchart
