Hi,
Here is an attempt at supporting the MIPI-CSI2 TX block from Cadence.
This IP block is able to receive 4 video streams and stream them over
a MIPI-CSI2 link using up to 4 lanes. Those streams are basically the
interfaces to controllers generating some video signals, like a camera
or a pattern generator.
It is able to map input streams to CSI2 virtual channels and datatypes
dynamically. The streaming devices choose their virtual channels
through an additional signal that is transparent to the CSI2-TX. The
datatypes however are yet another additional input signal, and can be
mapped to any CSI2 datatypes.
Since v4l2 doesn't really allow for that setup at the moment, this
preliminary version is a rather dumb one in order to start the
discussion on how to address this properly.
Let me know what you think!
Maxime
Changes from v9:
- Prevent the format to be retrieved on the CSI2 pad
- Set the default format on the pads when the user tries to set an
unsupported format
Changes from v8:
- Updated the copyright notice
- Used masks for the device config fields
- Used the mbus code directly in our format lookup function
- Removed the pad index check in pads get/set_format
- Prevent the format to be changed on the CSI2 pad
- Check for supported formats in set_format
- Rebased on 4.17-rc1
Changes from v7:
- Removed unused headers
- Fixed a function prefix inconsistency
- Added Niklas' Reviewed-by
Changes from v6:
- Added Niklas Reviewed-by on the bindings
- Added MODULE_LICENSE, MODULE_DESCRIPTION and MODULE_AUTHOR
Changes from v5:
- Changed the return type to void for csi2tx_stop
- Checked for the pad index in get/set_pad_format
- Made a comment that the DPHY registers are for the DPHY *interface*
register
Changes from v4:
- After playing a bit with the pad multiplexing patches, found that it
was making much more sense to have the subdev notifiers for the source
subdev rather for the sink that might even be outside of Linux control.
Removed the notifier for now.
Changes from v3:
- Added a comment about entity links walk concurrency
- Changed the default resolution to 1280x720
- Changed usleep_range calls to udelay
- Reworked the reference counting mechanism to remove a race
condition by adding a mutex instead of an atomic count
- Changed the entity function to MEDIA_ENT_F_VID_IF_BRIDGE
- Changed the name of the reg variable in _get_resources to dev_cfg
- Removed the redundant error message in the devm_ioremap_resource
error path
- Moved the subdev s_stream call before enabling the TX bridge
- Changed some int types to unsigned
- Init'd the pad formats properly
- Fixed typo in the CSI2TX_LANES_MAX define name
- Added Sakari Acked-by
Changes from v2:
- Use SPDX license header
- Use the lane mapping from DT
Changes from v1:
- Add a subdev notifier and start our downstream subdevice in
s_stream
- Based the decision to enable the stream or not on the link state
instead of whether a format was being set on the pad
- Put the controller back in reset when stopping the pipeline
- Clarified the enpoints number in the DT binding
- Added a default format for the pads
- Added some missing const
- Added more explicit comments
- Rebased on 4.15
Maxime Ripard (2):
dt-bindings: media: Add Cadence MIPI-CSI2 TX Device Tree bindings
v4l: cadence: Add Cadence MIPI-CSI2 TX driver
.../devicetree/bindings/media/cdns,csi2tx.txt | 98 ++++
drivers/media/platform/cadence/Kconfig | 11 +
drivers/media/platform/cadence/Makefile | 1 +
drivers/media/platform/cadence/cdns-csi2tx.c | 541 ++++++++++++++++++
4 files changed, 651 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/cdns,csi2tx.txt
create mode 100644 drivers/media/platform/cadence/cdns-csi2tx.c
--
2.17.0
