Hi Maxime,
Thanks for your patch,
On 2018-03-14 14:16:01 +0100, Maxime Ripard wrote:
> The Cadence MIPI-CSI2 TX controller is a CSI2 bridge that supports up to 4
> video streams and can output on up to 4 CSI-2 lanes, depending on the
> hardware implementation.
>
> It can operate with an external D-PHY, an internal one or no D-PHY at all
> in some configurations.
>
> Acked-by: Rob Herring <robh@xxxxxxxxxx>
> Acked-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
> Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxx>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> ---
> .../devicetree/bindings/media/cdns,csi2tx.txt | 98 ++++++++++++++++++++++
> 1 file changed, 98 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/cdns,csi2tx.txt
>
> diff --git a/Documentation/devicetree/bindings/media/cdns,csi2tx.txt b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt
> new file mode 100644
> index 000000000000..459c6e332f52
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt
> @@ -0,0 +1,98 @@
> +Cadence MIPI-CSI2 TX controller
> +===============================
> +
> +The Cadence MIPI-CSI2 TX controller is a CSI-2 bridge supporting up to
> +4 CSI lanes in output, and up to 4 different pixel streams in input.
> +
> +Required properties:
> + - compatible: must be set to "cdns,csi2tx"
> + - reg: base address and size of the memory mapped region
> + - clocks: phandles to the clocks driving the controller
> + - clock-names: must contain:
> + * esc_clk: escape mode clock
> + * p_clk: register bank clock
> + * pixel_if[0-3]_clk: pixel stream output clock, one for each stream
> + implemented in hardware, between 0 and 3
> +
> +Optional properties
> + - phys: phandle to the D-PHY. If it is set, phy-names need to be set
> + - phy-names: must contain "dphy"
> +
> +Required subnodes:
> + - ports: A ports node with one port child node per device input and output
> + port, in accordance with the video interface bindings defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt. The
> + port nodes are numbered as follows.
> +
> + Port Description
> + -----------------------------
> + 0 CSI-2 output
> + 1 Stream 0 input
> + 2 Stream 1 input
> + 3 Stream 2 input
> + 4 Stream 3 input
> +
> + The stream input port nodes are optional if they are not
> + connected to anything at the hardware level or implemented
> + in the design. Since there is only one endpoint per port,
> + the endpoints are not numbered.
> +
> +Example:
> +
> +csi2tx: csi-bridge@0d0e1000 {
> + compatible = "cdns,csi2tx";
> + reg = <0x0d0e1000 0x1000>;
> + clocks = <&byteclock>, <&byteclock>,
> + <&coreclock>, <&coreclock>,
> + <&coreclock>, <&coreclock>;
> + clock-names = "p_clk", "esc_clk",
> + "pixel_if0_clk", "pixel_if1_clk",
> + "pixel_if2_clk", "pixel_if3_clk";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + csi2tx_out: endpoint {
> + remote-endpoint = <&remote_in>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + csi2tx_in_stream0: endpoint {
> + remote-endpoint = <&stream0_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> +
> + csi2tx_in_stream1: endpoint {
> + remote-endpoint = <&stream1_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> +
> + csi2tx_in_stream2: endpoint {
> + remote-endpoint = <&stream2_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <4>;
> +
> + csi2tx_in_stream3: endpoint {
> + remote-endpoint = <&stream3_out>;
> + };
> + };
> + };
> +};
> --
> 2.14.3
>
--
Regards,
Niklas Söderlund
