Re: [PATCH v3 3/5] [RFT] ARM: dts: wheat: Fix ADV7513 address usage

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Kieran,

Thank you for the patch.

On Tuesday, 13 February 2018 00:07:51 EET Kieran Bingham wrote:
> From: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>
> 
> The r8a7792 Wheat board has two ADV7513 devices sharing a single i2c
> bus, however in low power mode the ADV7513 will reset it's slave maps to
> use the hardware defined default addresses.
> 
> The ADV7511 driver was adapted to allow the two devices to be registered
> correctly - but it did not take into account the fault whereby the
> devices reset the addresses.
> 
> This results in an address conflict between the device using the default
> addresses, and the other device if it is in low-power-mode.
> 
> Repair this issue by moving both devices away from the default address
> definitions.
> 
> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>

Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>

> ---
> v2:
>  - Addition to series
> 
> v3:
>  - Split map register addresses into individual declarations.
> 
>  arch/arm/boot/dts/r8a7792-wheat.dts | 12 ++++++++++--
>  1 file changed, 10 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts
> b/arch/arm/boot/dts/r8a7792-wheat.dts index b9471b67b728..42fff8837eab
> 100644
> --- a/arch/arm/boot/dts/r8a7792-wheat.dts
> +++ b/arch/arm/boot/dts/r8a7792-wheat.dts
> @@ -240,9 +240,16 @@
>  	status = "okay";
>  	clock-frequency = <400000>;
> 
> +	/*
> +	 * The adv75xx resets its addresses to defaults during low power power
> +	 * mode. Because we have two ADV7513 devices on the same bus, we must
> +	 * change both of them away from the defaults so that they do not
> +	 * conflict.
> +	 */
>  	hdmi@3d {
>  		compatible = "adi,adv7513";
> -		reg = <0x3d>;
> +		reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
> +		reg-names = "main", "cec", "edid", "packet";
> 
>  		adi,input-depth = <8>;
>  		adi,input-colorspace = "rgb";
> @@ -272,7 +279,8 @@
> 
>  	hdmi@39 {
>  		compatible = "adi,adv7513";
> -		reg = <0x39>;
> +		reg = <0x39>, <0x29>, <0x49>, <0x59>;
> +		reg-names = "main", "cec", "edid", "packet";
> 
>  		adi,input-depth = <8>;
>  		adi,input-colorspace = "rgb";

-- 
Regards,

Laurent Pinchart




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux