Hi Andy and Alan,
Thanks for the update.
A number of patches you've sent lately have arrived twice in slightly
different form. If that happens, could you reply and tell which one is the
right one, please?
Please see my comments below.
On Tue, Jan 30, 2018 at 12:52:59AM +0800, Andy Yeh wrote:
> From: Alan Chiang <alanx.chiang@xxxxxxxxx>
>
> DW9807 is a 10 bit DAC from Dongwoon, designed for linear
> control of voice coil motor.
>
> This driver creates a V4L2 subdevice and
> provides control to set the desired focus.
>
> Signed-off-by: Andy Yeh <andy.yeh@xxxxxxxxx>
> ---
> since v1:
> - changed author.
> since v2:
> - addressed outstanding comments.
> - enabled sequential write to update 2 registers in a single transaction.
> since v3:
> - addressed comments for v3.
> - Remove redundant codes and declar some variables as constant variable.
> - separate DT binding to another patch
>
> MAINTAINERS | 7 +
> drivers/media/i2c/Kconfig | 10 ++
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/dw9807.c | 319 +++++++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 337 insertions(+)
> create mode 100644 drivers/media/i2c/dw9807.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 845fc25..a339bb5 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -4385,6 +4385,13 @@ T: git git://linuxtv.org/media_tree.git
> S: Maintained
> F: drivers/media/i2c/dw9714.c
>
> +DONGWOON DW9807 LENS VOICE COIL DRIVER
> +M: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
> +L: linux-media@xxxxxxxxxxxxxxx
> +T: git git://linuxtv.org/media_tree.git
> +S: Maintained
> +F: drivers/media/i2c/dw9807.c
> +
> DOUBLETALK DRIVER
> M: "James R. Van Zandt" <jrv@xxxxxxxxxxxxxxx>
> L: blinux-list@xxxxxxxxxx
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index cb5d7ff..fd01842 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -325,6 +325,16 @@ config VIDEO_DW9714
> capability. This is designed for linear control of
> voice coil motors, controlled via I2C serial interface.
>
> +config VIDEO_DW9807
> + tristate "DW9807 lens voice coil support"
> + depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER
> + depends on VIDEO_V4L2_SUBDEV_API
> + ---help---
> + This is a driver for the DW9807 camera lens voice coil.
> + DW9807 is a 10 bit DAC with 100mA output current sink
> + capability. This is designed for linear control of
> + voice coil motors, controlled via I2C serial interface.
> +
> config VIDEO_SAA7110
> tristate "Philips SAA7110 video decoder"
> depends on VIDEO_V4L2 && I2C
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index 548a9ef..1b62639 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -23,6 +23,7 @@ obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o
> obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o
> obj-$(CONFIG_VIDEO_AD5820) += ad5820.o
> obj-$(CONFIG_VIDEO_DW9714) += dw9714.o
> +obj-$(CONFIG_VIDEO_DW9807) += dw9807.o
> obj-$(CONFIG_VIDEO_ADV7170) += adv7170.o
> obj-$(CONFIG_VIDEO_ADV7175) += adv7175.o
> obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o
> diff --git a/drivers/media/i2c/dw9807.c b/drivers/media/i2c/dw9807.c
> new file mode 100644
> index 0000000..607e3ac
> --- /dev/null
> +++ b/drivers/media/i2c/dw9807.c
> @@ -0,0 +1,319 @@
> +// Copyright (C) 2018 Intel Corporation
> +// SPDX-License-Identifier: GPL-2.0
> +
> +#include <linux/acpi.h>
> +#include <linux/delay.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/pm_runtime.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +
> +#define DW9807_NAME "dw9807"
> +#define DW9807_MAX_FOCUS_POS 1023
> +/*
> + * This sets the minimum granularity for the focus positions.
> + * A value of 1 gives maximum accuracy for a desired focus position
> + */
> +#define DW9807_FOCUS_STEPS 1
> +/*
> + * This acts as the minimum granularity of lens movement.
> + * Keep this value power of 2, so the control steps can be
> + * uniformly adjusted for gradual lens movement, with desired
> + * number of control steps.
> + */
> +#define DW9807_CTRL_STEPS 16
> +#define DW9807_CTRL_DELAY_US 1000
> +
> +#define DW9807_CTL_ADDR 0x02
> +/*
> + * DW9807 separates two registers to control the VCM position.
> + * One for MSB value, another is LSB value.
> + */
> +#define DW9807_MSB_ADDR 0x03
> +#define DW9807_LSB_ADDR 0x04
> +#define DW9807_STATUS_ADDR 0x05
> +#define DW9807_MODE_ADDR 0x06
> +#define DW9807_RESONANCE_ADDR 0x07
> +
> +#define MAX_RETRY 10
> +
> +struct dw9807_device {
> + struct v4l2_ctrl_handler ctrls_vcm;
> + struct v4l2_subdev sd;
> + u16 current_val;
> +};
> +
> +static inline struct dw9807_device *sd_to_dw9807_vcm(struct v4l2_subdev *subdev)
> +{
> + return container_of(subdev, struct dw9807_device, sd);
> +}
> +
> +static int dw9807_i2c_check(struct i2c_client *client)
> +{
> + const char status_addr = DW9807_STATUS_ADDR;
> + char status_result = 0x1;
> + int ret;
> +
> + ret = i2c_master_send(client, (const char *)&status_addr, sizeof(status_addr));
> + if (ret != sizeof(status_addr)) {
> + dev_err(&client->dev, "I2C write STATUS address fail ret = %d\n",
> + ret);
> + return -EIO;
> + }
> +
> + ret = i2c_master_recv(client, (char *)&status_result, sizeof(status_result));
> + if (ret != sizeof(status_result)) {
> + dev_err(&client->dev, "I2C read STATUS value fail ret=%d\n",
> + ret);
> + return -EIO;
> + }
> +
> + return status_result;
> +}
> +
> +static int dw9807_set_dac(struct i2c_client *client, u16 data)
> +{
> + int ret, retry = 0;
> + const char tx_data[3] = {DW9807_MSB_ADDR, (char)((data >> 8) & 0x03), (char)(data & 0xFF)};
Please remove the typecast, you won't need that.
And also split the line, it's over 80 characters.
ret and retry would be better declared after tx_data (return values,
temporary and loop variables generally go last).
> +
> + /*
> + * According to the datasheet, need to check the bus status before we
> + * write VCM position. This ensure that we really write the value
> + * into the register
> + */
> + while (dw9807_i2c_check(client) != 0) {
> + if (MAX_RETRY == ++retry) {
> + dev_err(&client->dev, "Cannot do the write operation because VCM is busy\n");
> + return -EIO;
> + }
> + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10);
> + }
> +
> + /* Write VCM position to registers */
> + ret = i2c_master_send(client, (const char *)&tx_data, sizeof(tx_data));
No need for typecast here either.
> + if (ret != sizeof(tx_data)) {
> + dev_err(&client->dev, "I2C write MSB fail\n");
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int dw9807_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct dw9807_device *dev_vcm = container_of(ctrl->handler, struct dw9807_device, ctrls_vcm);
> +
> + if (ctrl->id == V4L2_CID_FOCUS_ABSOLUTE) {
> + struct i2c_client *client = v4l2_get_subdevdata(&dev_vcm->sd);
> +
> + dev_vcm->current_val = ctrl->val;
> + return dw9807_set_dac(client, ctrl->val);
> + }
> +
> + return -EINVAL;
> +}
> +
> +static const struct v4l2_ctrl_ops dw9807_vcm_ctrl_ops = {
> + .s_ctrl = dw9807_set_ctrl,
> +};
> +
> +static int dw9807_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> +{
> + int rval;
> +
> + rval = pm_runtime_get_sync(sd->dev);
> + if (rval < 0) {
> + pm_runtime_put_noidle(sd->dev);
> + return rval;
> + }
> +
> + return 0;
> +}
> +
> +static int dw9807_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> +{
> + pm_runtime_put(sd->dev);
> +
> + return 0;
> +}
> +
> +static const struct v4l2_subdev_internal_ops dw9807_int_ops = {
> + .open = dw9807_open,
> + .close = dw9807_close,
> +};
> +
> +static const struct v4l2_subdev_ops dw9807_ops = { };
> +
> +static void dw9807_subdev_cleanup(struct dw9807_device *dw9807_dev)
> +{
> + v4l2_async_unregister_subdev(&dw9807_dev->sd);
> + v4l2_ctrl_handler_free(&dw9807_dev->ctrls_vcm);
> + media_entity_cleanup(&dw9807_dev->sd.entity);
> +}
> +
> +static int dw9807_init_controls(struct dw9807_device *dev_vcm)
> +{
> + struct v4l2_ctrl_handler *hdl = &dev_vcm->ctrls_vcm;
> + const struct v4l2_ctrl_ops *ops = &dw9807_vcm_ctrl_ops;
> + struct i2c_client *client = v4l2_get_subdevdata(&dev_vcm->sd);;
> +
> + v4l2_ctrl_handler_init(hdl, 1);
> +
> + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_FOCUS_ABSOLUTE,
> + 0, DW9807_MAX_FOCUS_POS, DW9807_FOCUS_STEPS, 0);
> +
> + dev_vcm->sd.ctrl_handler = hdl;
> + if (hdl->error) {
> + dev_err(&client->dev, "%s fail error: 0x%x\n",
> + __func__, hdl->error);
> + return hdl->error;
> + }
> +
> + return 0;
> +}
> +
> +static int dw9807_probe(struct i2c_client *client)
> +{
> + struct dw9807_device *dw9807_dev;
> + int rval;
> +
> + dw9807_dev = devm_kzalloc(&client->dev, sizeof(*dw9807_dev),
> + GFP_KERNEL);
> + if (dw9807_dev == NULL)
> + return -ENOMEM;
> +
> + v4l2_i2c_subdev_init(&dw9807_dev->sd, client, &dw9807_ops);
> + dw9807_dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> + dw9807_dev->sd.internal_ops = &dw9807_int_ops;
> +
> + rval = dw9807_init_controls(dw9807_dev);
> + if (rval)
> + goto err_cleanup;
> +
> + rval = media_entity_pads_init(&dw9807_dev->sd.entity, 0, NULL);
> + if (rval < 0)
> + goto err_cleanup;
> +
> + dw9807_dev->sd.entity.function = MEDIA_ENT_F_LENS;
> +
> + rval = v4l2_async_register_subdev(&dw9807_dev->sd);
> + if (rval < 0)
> + goto err_cleanup;
> +
> + pm_runtime_set_active(&client->dev);
> + pm_runtime_enable(&client->dev);
> + pm_runtime_idle(&client->dev);
> +
> + return 0;
> +
> +err_cleanup:
> + dw9807_subdev_cleanup(dw9807_dev);
> + return rval;
> +}
> +
> +static int dw9807_remove(struct i2c_client *client)
> +{
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd);
> +
> + pm_runtime_disable(&client->dev);
> + pm_runtime_set_suspended(&client->dev);
> +
> + dw9807_subdev_cleanup(dw9807_dev);
> +
> + return 0;
> +}
> +
> +/*
> + * This function sets the vcm position, so it consumes least current
> + * The lens position is gradually moved in units of DW9807_CTRL_STEPS,
> + * to make the movements smoothly.
> + */
> +static int __maybe_unused dw9807_vcm_suspend(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd);
> + int ret, val;
> + const char tx_data[2] = { DW9807_CTL_ADDR, 0x01};
^ space here
tx_data should precede ret and val.
> +
> + for (val = dw9807_dev->current_val & ~(DW9807_CTRL_STEPS - 1);
> + val >= 0; val -= DW9807_CTRL_STEPS) {
> + ret = dw9807_set_dac(client, val);
> + if (ret)
> + dev_err_once(dev, "%s I2C failure: %d", __func__, ret);
> + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10);
> + }
> +
> + /* Power down */
> + ret = i2c_master_send(client, (const char *)&tx_data, sizeof(tx_data));
Please remove typecast here.
Both this and the above comment apply to corresponding resume function
below.
> +
> + if (ret != sizeof(tx_data)) {
> + dev_err(&client->dev, "I2C write CTL fail\n");
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * This function sets the vcm position to the value set by the user
> + * through v4l2_ctrl_ops s_ctrl handler
> + * The lens position is gradually moved in units of DW9807_CTRL_STEPS,
> + * to make the movements smoothly.
> + */
> +static int __maybe_unused dw9807_vcm_resume(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9807_device *dw9807_dev = sd_to_dw9807_vcm(sd);
> + int ret, val;
> + const char tx_data[2] = { DW9807_CTL_ADDR, 0x00};
> +
> + /* Power on */
> + ret = i2c_master_send(client, (const char *)&tx_data, sizeof(tx_data));
> + if (ret != sizeof(tx_data)) {
> + dev_err(&client->dev, "I2C write CTL fail\n");
> + return -EIO;
> + }
> +
> + for (val = dw9807_dev->current_val % DW9807_CTRL_STEPS;
> + val < dw9807_dev->current_val + DW9807_CTRL_STEPS - 1;
> + val += DW9807_CTRL_STEPS) {
> + ret = dw9807_set_dac(client, val);
> + if (ret)
> + dev_err_ratelimited(dev, "%s I2C failure: %d",
> + __func__, ret);
> + usleep_range(DW9807_CTRL_DELAY_US, DW9807_CTRL_DELAY_US + 10);
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id dw9807_of_table[] = {
> + { .compatible = "dongwoon,dw9807" },
> + { { 0 } }
> +};
> +MODULE_DEVICE_TABLE(of, dw9807_of_table);
> +
> +static const struct dev_pm_ops dw9807_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(dw9807_vcm_suspend, dw9807_vcm_resume)
> + SET_RUNTIME_PM_OPS(dw9807_vcm_suspend, dw9807_vcm_resume, NULL)
> +};
> +
> +static struct i2c_driver dw9807_i2c_driver = {
> + .driver = {
> + .name = DW9807_NAME,
> + .pm = &dw9807_pm_ops,
> + .of_match_table = dw9807_of_table,
> + },
> + .probe_new = dw9807_probe,
> + .remove = dw9807_remove,
> +};
> +
> +module_i2c_driver(dw9807_i2c_driver);
> +
> +MODULE_AUTHOR("Chiang, Alan <alanx.chiang@xxxxxxxxx>");
> +MODULE_DESCRIPTION("DW9807 VCM driver");
> +MODULE_LICENSE("GPL v2");
--
Sakari Ailus
sakari.ailus@xxxxxxxxxxxxxxx
