On Wed, Jan 17, 2018 at 09:35:53AM +0100, jacopo mondi wrote:
> Hi Sakari,
> it's the second series this week where I fail to handle BT.656
> properly, sorry about this :)
No worries. I guess I forgot your reply. If the hardware doesn't support
Bt.656 then the current definition is fine.
Acked-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
>
> On Wed, Jan 17, 2018 at 09:59:59AM +0200, Sakari Ailus wrote:
> > Hi Jacopo,
> >
> > On Tue, Jan 16, 2018 at 10:44:53PM +0100, Jacopo Mondi wrote:
> > > Add bindings documentation for Renesas Capture Engine Unit (CEU).
> > >
> > > Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> > > Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> > > Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> > > Acked-by: Hans Verkuil <hans.verkuil@xxxxxxxxx>
> > > ---
> > > .../devicetree/bindings/media/renesas,ceu.txt | 81 ++++++++++++++++++++++
> > > 1 file changed, 81 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt
> > >
> > > diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt
> > > new file mode 100644
> > > index 0000000..590ee27
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt
> > > @@ -0,0 +1,81 @@
> > > +Renesas Capture Engine Unit (CEU)
> > > +----------------------------------------------
> > > +
> > > +The Capture Engine Unit is the image capture interface found in the Renesas
> > > +SH Mobile and RZ SoCs.
> > > +
> > > +The interface supports a single parallel input with data bus width of 8 or 16
> > > +bits.
> > > +
> > > +Required properties:
> > > +- compatible: Shall be "renesas,r7s72100-ceu" for CEU units found in RZ/A1-H
> > > + and RZ/A1-M SoCs.
> > > +- reg: Registers address base and size.
> > > +- interrupts: The interrupt specifier.
> > > +
> > > +The CEU supports a single parallel input and should contain a single 'port'
> > > +subnode with a single 'endpoint'. Connection to input devices are modeled
> > > +according to the video interfaces OF bindings specified in:
> > > +Documentation/devicetree/bindings/media/video-interfaces.txt
> > > +
> > > +Optional endpoint properties applicable to parallel input bus described in
> > > +the above mentioned "video-interfaces.txt" file are supported.
> > > +
> > > +- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
> > > + If property is not present, default is active high.
> > > +- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
> > > + If property is not present, default is active high.
> >
> > Does the hardware support Bt.656? If it does, you need to tell the
> > difference between the parallel interface with default sync polarity and
> > Bt.656 interfaces. With the above it's ambiguous.
>
> No, it does not support BT.656.
>
> I'm listing them as -required- endpoint properties. If they are not
> specified the drivers fails during probe:
>
> renesas-ceu e8210000.ceu: Only parallel input supported.
>
> Thanks
> j
>
> >
> > > +
> > > +Example:
> > > +
> > > +The example describes the connection between the Capture Engine Unit and an
> > > +OV7670 image sensor connected to i2c1 interface.
> > > +
> > > +ceu: ceu@e8210000 {
> > > + reg = <0xe8210000 0x209c>;
> > > + compatible = "renesas,r7s72100-ceu";
> > > + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> > > +
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&vio_pins>;
> > > +
> > > + status = "okay";
> > > +
> > > + port {
> > > + ceu_in: endpoint {
> > > + remote-endpoint = <&ov7670_out>;
> > > +
> > > + hsync-active = <1>;
> > > + vsync-active = <0>;
> > > + };
> > > + };
> > > +};
> > > +
> > > +i2c1: i2c@fcfee400 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&i2c1_pins>;
> > > +
> > > + status = "okay";
> > > +
> > > + clock-frequency = <100000>;
> > > +
> > > + ov7670: camera@21 {
> > > + compatible = "ovti,ov7670";
> > > + reg = <0x21>;
> > > +
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&vio_pins>;
> > > +
> > > + reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
> > > + powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
> > > +
> > > + port {
> > > + ov7670_out: endpoint {
> > > + remote-endpoint = <&ceu_in>;
> > > +
> > > + hsync-active = <1>;
> > > + vsync-active = <0>;
> > > + };
> > > + };
> > > + };
> > > +};
> > > --
> > > 2.7.4
> > >
> >
> > --
> > Sakari Ailus
> > e-mail: sakari.ailus@xxxxxx
--
Sakari Ailus
e-mail: sakari.ailus@xxxxxx
