Re: [PATCH v4 2/3] media: ov7740: Document device tree bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

On Wed, Nov 01, 2017 at 04:51:57PM -0500, Rob Herring wrote:
> On Tue, Oct 31, 2017 at 09:11:44AM +0800, Wenyou Yang wrote:
> > Add the device tree binding documentation for the ov7740 sensor driver.
> > 
> > Signed-off-by: Wenyou Yang <wenyou.yang@xxxxxxxxxxxxx>
> > ---
> > 
> > Changes in v4: None
> > Changes in v3:
> >  - Explicitly document the "remote-endpoint" property.
> > 
> > Changes in v2: None
> > 
> >  .../devicetree/bindings/media/i2c/ov7740.txt       | 47 ++++++++++++++++++++++
> >  1 file changed, 47 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov7740.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/media/i2c/ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ov7740.txt
> > new file mode 100644
> > index 000000000000..af781c3a5f0e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/ov7740.txt
> > @@ -0,0 +1,47 @@
> > +* Omnivision OV7740 CMOS image sensor
> > +
> > +The Omnivision OV7740 image sensor supports multiple output image
> > +size, such as VGA, and QVGA, CIF and any size smaller. It also
> > +supports the RAW RGB and YUV output formats.
> > +
> > +The common video interfaces bindings (see video-interfaces.txt) should
> > +be used to specify link to the image data receiver. The OV7740 device
> > +node should contain one 'port' child node with an 'endpoint' subnode.
> > +
> > +Required Properties:
> > +- compatible:	"ovti,ov7740".
> > +- reg:		I2C slave address of the sensor.
> > +- clocks:	Reference to the xvclk input clock.
> > +- clock-names:	"xvclk".
> > +
> > +Optional Properties:
> > +- reset-gpios: Rreference to the GPIO connected to the reset_b pin,
> > +  if any. Active low with pull-ip resistor.
> > +- powerdown-gpios: Reference to the GPIO connected to the pwdn pin,
> > +  if any. Active high with pull-down resistor.
> > +
> > +Endpoint node mandatory properties:
> > +- remote-endpoint: A phandle to the bus receiver's endpoint node.
> 
> This is not really necessary. What's required is documenting how many 
> ports and how many endpoints for each port which you have above.

I actually requested adding that as the practice, as far as I've understood
it, has been to document all properties relevant for the hardware (apart
from things such as assigned-clocks etc.).

The port and endpoints have been elaborated above and I think that should
be fine as-is.

The graph bindings document (referred by video-interfaces.txt) the
remote-endpoint property in an endpoint as an optional property, however
you can't really use the sensor if it's not connected to anything. The same
goes for video-interfaces.txt: remote-endpoint in an endpoint is optional.

I have no objections removing remote-endpoint here, though, if you think
it's not relevant here.

-- 
Kind regards,

Sakari Ailus
e-mail: sakari.ailus@xxxxxx



[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux