On Fri, Oct 20, 2017 at 9:23 AM, Hans Verkuil <hverkuil@xxxxxxxxx> wrote: >> >> I see the AVI infoframe has hdmi_quantization_range and >> hdmi_ycc_quantization_range along with vid_code. >> >> I'm not at all clear what to do with this information. Is there >> anything you see in the datasheet [1] that points to something I need >> to be doing? > > You can ignore hdmi_ycc_quantization_range, it is the hdmi_quantization_range > that you need to read out. > > The TDA can receive the following formats: > > RGB Full Range > RGB Limited Range > YUV Bt.601 (aka SMPTE 170M) > YUV Rec.709 > > The YUV formats are always limited range. > > The TDA can transmit RGB and YUV to the SoC. You want RGB to be full range and > YUV to be limited range. YUV can be either 601 or 709. > > So if the TDA transmits RGB then you need to support the following conversions: > > RGB Full -> RGB Full > RGB Limited -> RGB Full > YUV 601 -> RGB Full > YUV 709 -> RGB Full > > And if the TDA transmits YUV then you need these conversions: > > RGB Full -> YUV601 or YUV709 > RGB Limited -> YUV601 or YUV709 > YUV601 -> YUV601 > YUV709 -> YUV709 > > For the RGB to YUV conversion you have a choice of converting to YUV601 or 709. > I recommend to either always convert to YUV601 or to let it depend on the resolution > (SDTV YUV601, HDTV YUV709). > Ok - this is a good explanation that I should be able to follow. I will make sure to take into account hdmi_quantization_range when I setup the colorspace conversion matrix for v3. > Ideally the application should specify what it wants, but we don't have any API > support for that. > <snip> >> >> The TDA1997x provides only the vertical/horizontal periods and the >> horizontal pulse >> width (section 8.3.4 of datasheet [1]). >> >> Can you point me to a good primer on the relationship between these >> values and the h/v back/front porch? > > The blanking consists of a front porch width, a sync width and a back porch width. > 'Width' is normally measured in pixels. Vertical blanking is the same, except that > is measured in lines. All these values are defined in the standards that define these > timings (e.g. VESA DMT, CTA-861). > > So for 1080p60 the active video is 1920x1080. After each line of 1920 pixels you > have 88 'pixels' of front porch, a sync pulse of 44 'pixels' and a back porch of > 148 pixels. Total frame width is 2200. Similar for the vertical. > > A good HDMI receiver will give you the exact values for these blanking sizes. > Especially the sync width/height is important since that can provide additional > format information when receiving VESA formats. > > It looks as if the TDA does not measure in exact pixels but in 27 MHz clock > periods. Which is an approximation only. > > So it appears that what you do is the best you can do. > > Although I wonder about the hsper: the datasheet suggests that this is the width, > not a period. What is the value you read out when you receive 1080p60? If that > would be an exact width, then that would help a lot since you can compare that > against bt->hsync. Here's a list of source modes and the vertical/horizontal period and horizontal pulse width returned from the TDA: 00: VESA640x480P_60HZ 450427 856 101 01: VESA800x600P_60HZ 447620 711 85 02: VESA1024x768P_60HZ 449952 557 55 03: VESA1280x768P_60HZ 450021 568 11 04: VESA1360x768P_60HZ 449867 564 34 05: VESA1280x960P_60HZ 449981 448 55 06: VESA1280x1024P_60HZ 449833 420 27 07: VESA1400x1050P_60HZ 450372 416 7 08: VESA1600x1200P_60HZ 449981 358 27 09: VESA1920x1200P_60HZ 450355 363 4 10: CEAVIC1440x480I_60HZ 450430 1714 123 11: CEAVIC720x480P_60HZ 450430 856 61 12: CEAVIC1280x720P_60HZ 449981 598 13 13: CEAVIC1280x720P_59.94 450431 599 13 14: CEAVIC1920x1080I_60HZ 449981 798 15 15: CEAVIC1920x1080I_59.95HZ 450431 799 15 16: CEAVIC1920x1080P_30HZ 899962 798 15 17: CEAVIC1920x1080P_29.95HZ 900862 799 15 18: CEAVIC1920x1080P_24HZ 1124953 998 15 19: CEAVIC1920x1080P_23.976HZ 1126077 999 15 20: CEAVIC1920x1080P_60HZ 449981 398 7 21: CEAVIC1920x1080P_59.94HZ 450431 399 7 22: CEAVIC1440x576I_50HZ 539976 1726 127 23: CEAVIC720x576P_50HZ 539976 862 63 24: CEAVIC1280x720P_50HZ 539977 718 13 25: CEAVIC1920x1080I_50HZ 539977 958 15 26: CEAVIC1920x1080P_25HZ 1079954 958 15 27: CEAVIC1920x1080P_50HZ 539977 478 7 so 1080p60 gives a hswidth=7 Tim
