Cc: Rob Herring <robh@xxxxxxxxxx>
Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
---
v2:
- add vendor prefix and remove _ from vidout-portcfg
- remove _ from labels
- remove max-pixel-rate property
- describe and provide example for single output port
- use new audio port bindings
---
.../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++
1 file changed, 179 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt
diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
new file mode 100644
index 0000000..269d7f0
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
@@ -0,0 +1,179 @@
+Device-Tree bindings for the NXP TDA1997x HDMI receiver
+
+The TDA19971/73 are HDMI video receivers.
+
+The TDA19971 Video port output pins can be used as follows:
+ - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
+ - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
+ - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
+ - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
+ - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
+ - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
+ - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The TDA19973 Video port output pins can be used as follows:
+ - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
+ - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
+ - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The Video port output pins are mapped via 4-bit 'pin groups' allowing
+for a variety fo connection possibilities including swapping pin order within
+pin groups. The video_portcfg device-tree property consists of register mapping
+pairs which map a chip-specific VP output register to a 4-bit pin group. If
+the pin group needs to be bit-swapped you can use the *_S pin-group defines.
+
+Required Properties:
+ - compatible :
+ - "nxp,tda19971" for the TDA19971
+ - "nxp,tda19973" for the TDA19973
+ - reg : I2C slave address
+ - interrupts : The interrupt number
+ - DOVDD-supply : Digital I/O supply
+ - DVDD-supply : Digital Core supply
+ - AVDD-supply : Analog supply
+ - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups.
+
+Optional Properties:
+ - nxp,audout-format : DAI bus format: "i2s" or "spdif".
+ - nxp,audout-width : width of audio output data bus (1-4).
+ - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
+ - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec
+ mclk.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Optional Endpoint Properties:
+ The following three properties are defined in video-interfaces.txt and
+ are valid for source endpoints only:
+ - hsync-active: Horizontal synchronization polarity. Defaults to active high.
+ - vsync-active: Vertical synchronization polarity. Defaults to active high.
+ - data-active: Data polarity. Defaults to active high.
+
+Examples:
+ - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
+ 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+ hdmi-receiver@48 {
+ compatible = "nxp,tda19971";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tda1997x>;
+ reg = <0x48>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ DOVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_1p8v>;
+ /* audio */
+ #sound-dai-cells = <0>;
+ nxp,audout-format = "i2s";
+ nxp,audout-layout = <0>;
+ nxp,audout-width = <16>;
+ nxp,audout-mclk-fs = <128>;
+ /*
+ * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+ * and Y[11:4] across 16bits in the same pixclk cycle.
+ */
+ nxp,vidout-portcfg =
+ /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+ < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+ /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+ < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+ /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+ < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+ /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+ < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+ port {
+ tda1997x_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <16>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ data-active = <1>;
+ };
+ };
+ };
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+ 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+ hdmi-receiver@48 {
+ compatible = "nxp,tda19971";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tda1997x>;
+ reg = <0x48>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ DOVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_1p8v>;
+ /* audio */
+ #sound-dai-cells = <0>;
+ nxp,audout-format = "i2s";
+ nxp,audout-layout = <0>;
+ nxp,audout-width = <16>;
+ nxp,audout-mclk-fs = <128>;
+ /*
+ * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+ * and Y[11:4] across 16bits in the same pixclk cycle.
+ */
+ nxp,vidout-portcfg =
+ /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+ < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+ /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+ < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+ /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+ < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+ /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+ < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+ port {
+ tda1997x_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <16>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ data-active = <1>;
+ };
+ };
+ };
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+ 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+ hdmi-receiver@48 {
+ compatible = "nxp,tda19971";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tda1997x>;
+ reg = <0x48>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ DOVDD-supply = <®_3p3v>;
+ AVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_1p8v>;
+ /* audio */
+ #sound-dai-cells = <0>;
+ nxp,audout-format = "i2s";
+ nxp,audout-layout = <0>;
+ nxp,audout-width = <16>;
+ nxp,audout-mclk-fs = <128>;
+ /*
+ * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
+ * 2 pixclk cycles.
+ */
+ nxp,vidout-portcfg =
+ /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+ < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
+ /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+ < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
+
+ port {
+ tda1997x_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <16>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ data-active = <1>;
+ };
+ };
+ };
+
--
2.7.4
