Hi Philipp,
2017-08-07 16:17 GMT+08:00 Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>:
> Hi Jacob,
>
> On Mon, 2017-08-07 at 15:11 +0800, Jacob Chen wrote:
>> Hi all,
>>
>> 2017-07-25 10:34 GMT+08:00 Jacob Chen <jacob-chen@xxxxxxxxxx>:
>> > According to datasheet, BIT5 in reg-0x4800 are used to
>> > enable/disable clock lane gate.
>> >
>> > It's wrong to make clock lane free running before
>> > sensor stream on was called, while the mipi phy
>> > are not initialized.
>> >
>> > Signed-off-by: Jacob Chen <jacob-chen@xxxxxxxxxx>
>>>
>> > ---
>> > drivers/media/i2c/ov5647.c | 10 +++++++++-
>> > 1 file changed, 9 insertions(+), 1 deletion(-)
>> >
>> > diff --git a/drivers/media/i2c/ov5647.c b/drivers/media/i2c/ov5647.c
>> > index 95ce90f..d3e6fd0 100644
>> > --- a/drivers/media/i2c/ov5647.c
>> > +++ b/drivers/media/i2c/ov5647.c
>> > @@ -253,6 +253,10 @@ static int ov5647_stream_on(struct v4l2_subdev *sd)
>> > {
>> > int ret;
>> >
>> > + ret = ov5647_write(sd, 0x4800, 0x04);
>> > + if (ret < 0)
>> > + return ret;
>> > +
>> > ret = ov5647_write(sd, 0x4202, 0x00);
>> > if (ret < 0)
>> > return ret;
>> > @@ -264,6 +268,10 @@ static int ov5647_stream_off(struct v4l2_subdev *sd)
>> > {
>> > int ret;
>> >
>> > + ret = ov5647_write(sd, 0x4800, 0x25);
>> > + if (ret < 0)
>> > + return ret;
>> > +
>> > ret = ov5647_write(sd, 0x4202, 0x0f);
>> > if (ret < 0)
>> > return ret;
>> > @@ -320,7 +328,7 @@ static int __sensor_init(struct v4l2_subdev *sd)
>> > return ret;
>> > }
>> >
>> > - return ov5647_write(sd, 0x4800, 0x04);
>> > + return ov5647_stream_off(sd);
>> > }
>> >
>> > static int ov5647_sensor_power(struct v4l2_subdev *sd, int on)
>> > --
>> > 2.7.4
>> >
>>
>> Can anyone comment on it?
>>
>> I saw there is a same discussion in https://patchwork.kernel.org/patch/9569031/
>> There is a comment in i.MX CSI2 driver.
>> "
>> Configure MIPI Camera Sensor to put all Tx lanes in LP-11 state.
>> This must be carried out by the MIPI sensor's s_power(ON) subdev
>> op.
>> "
>> That's what this patch do, sensor driver should make sure that clock
>> lanes are in stop state while not streaming.
>
> This is not the same, as far as I can tell. BIT(5) is just clock lane
> gating, as you describe above. To put the bus into LP-11 state, BIT(2)
> needs to be set.
>
Yeah, but i double that clock lane is not in LP11 when continue clock
mode is enabled.
> regards
> Philipp
>
