Hi Sylwester,
On 25-06-2017 22:13, Sylwester Nawrocki wrote:
> Hi Jose,
>
> Thank you for addressing my review comments. Couple more suggestions below.
>
> On 06/20/2017 07:26 PM, Jose Abreu wrote:
>> This adds support for the Synopsys Designware HDMI RX PHY e405. This
>> phy receives and decodes HDMI video that is delivered to a controller.
>> +static int dw_phy_config(struct dw_phy_dev *dw_dev, unsigned char color_depth,
>> + bool hdmi2, bool scrambling)
>> +{
>> + phy_reset(dw_dev, 1);
>> + phy_pddq(dw_dev, 1);
>> + phy_svsmode(dw_dev, 1);
>> +
>> + phy_zcal_reset(dw_dev);
>> + do {
>> + udelay(1000);
> Could be mdelay(1) or better e.g. usleep_range(1000, 1100);
Ok.
>
>> + zcal_done = phy_zcal_done(dw_dev);
>> + } while (!zcal_done && timeout--);
>> +
>> + if (!zcal_done) {
>> + dev_err(dw_dev->dev, "Zcal calibration failed\n");
>> + return -ETIMEDOUT;
>> + }
>> + return 0;
>> +}
>> +static int dw_phy_probe(struct platform_device *pdev)
>> +{
>> + struct dw_phy_pdata *pdata = pdev->dev.platform_data;
>> + struct device *dev = &pdev->dev;
>> + struct dw_phy_dev *dw_dev;
>> + struct v4l2_subdev *sd;
>> + int ret;
>> +
>> + dev_dbg(dev, "probe start\n");
>> +
>> + /* Resource allocation */
> This comment is not needed.
>
>> + dw_dev = devm_kzalloc(dev, sizeof(*dw_dev), GFP_KERNEL);
>> + if (!dw_dev)
>> + return -ENOMEM;
>> +
>> + /* Resource initialization */
> Ditto.
Ok.
>
>> + if (!pdata) {
>> + dev_err(dev, "no platform data suplied\n");
>> + return -EINVAL;
>> + }
>> +
>> + dw_dev->dev = dev;
>> + dw_dev->config = pdata;
>> + dw_dev->version = 405;
> How about storing the version number in the dw_hdmi_phy_e405_id[] table
> and retrieving it here with of_device_get_match_data() ?
Yeah, seems nice :)
>
>> + mutex_init(&dw_dev->lock);
>> +
>> + /* Get config clock value */
> The comment is not needed, it's clear from the code we are getting the clock
> and its rate.
Ok.
>
>> + dw_dev->clk = devm_clk_get(dev, "cfg-clk");
> As Rob suggested, it would be good to change name of the clock to just "cfg".
Yes, I will change.
>
>> + if (IS_ERR(dw_dev->clk)) {
>> + dev_err(dev, "failed to get cfg-clk\n");
>> + return PTR_ERR(dw_dev->clk);
>> + }
>> +
>> + ret = clk_prepare_enable(dw_dev->clk);
>> + if (ret) {
>> + dev_err(dev, "failed to enable cfg-clk\n");
>> + return ret;
>> + }
>> +
>> + dw_dev->cfg_clk = clk_get_rate(dw_dev->clk) / 1000000;
> 1000000U ?
Ok.
>
>> + if (!dw_dev->cfg_clk) {
>> + dev_err(dev, "invalid cfg-clk frequency\n");> + ret = -EINVAL;
>> + goto err_clk;
>> + }
>> +
>> + /* V4L2 initialization */
>> + sd = &dw_dev->sd;
>> + v4l2_subdev_init(sd, &dw_phy_sd_ops);
>> + strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
>> + sd->dev = dev;
>> +
>> + /* Force phy disabling */
>> + dw_dev->phy_enabled = true;
>> + dw_phy_disable(dw_dev);
>> +
>> + /* Register subdev */
>> + ret = v4l2_async_register_subdev(sd);
>> + if (ret) {
>> + dev_err(dev, "failed to register subdev\n");
>> + goto err_clk;
>> + }
>> +
>> + /* All done */
> Superfluous comment.
Ok.
>
>> + dev_set_drvdata(dev, sd);
>> + dev_info(dev, "driver probed (cfg-clk=%d)\n", dw_dev->cfg_clk);
> This should be at dev_dbg() level.
Ok.
>
>> + return 0;
>> +
>> +err_clk:
>> + clk_disable_unprepare(dw_dev->clk);
>> + return ret;
>> +}
>> +
>> +static int dw_phy_remove(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
> The assignment here could be dropped and &pdev->dev used directly below.
Ok.
>
>> + struct v4l2_subdev *sd = dev_get_drvdata(dev);
>> + struct dw_phy_dev *dw_dev = to_dw_dev(sd);
>> +
>> + v4l2_async_unregister_subdev(sd);
>> + clk_disable_unprepare(dw_dev->clk);
>> + dev_info(dev, "driver removed\n");
> This should be at dev_dbg() level or dropped entirely.
Ok.
Thanks for the review!
Best regards,
Jose Miguel Abreu
>
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id dw_hdmi_phy_e405_id[] = {
>> + { .compatible = "snps,dw-hdmi-phy-e405" },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, dw_hdmi_phy_e405_id);
> --
> Regards,
> Sylwester
