Re: [PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jun 7, 2017 at 11:33 AM, Steve Longerbeam <slongerbeam@xxxxxxxxx> wrote:
> Enables the ADV7180 decoder sensor. The ADV7180 connects to the
> parallel-bus mux input on ipu1_csi0_mux.
>
> The ADV7180 power pin is via max7310_b port expander.
>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
>
> - Use IRQ_TYPE_LEVEL_LOW instead of 0x8 for interrupt type for clarity.
> - For 8-bit parallel IPU1-CSI0 bus connection only data[12-19] are used.
>
> Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
> ---
>  arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 50 ++++++++++++++++++++++++++++++++
>  1 file changed, 50 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> index 1212f82..c24af28 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> @@ -124,6 +124,21 @@
>                         #size-cells = <0>;
>                         reg = <1>;
>
> +                       adv7180: camera@21 {
> +                               compatible = "adi,adv7180";
> +                               reg = <0x21>;
> +                               powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
> +                               interrupt-parent = <&gpio1>;
> +                               interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> +
> +                               port {
> +                                       adv7180_to_ipu1_csi0_mux: endpoint {
> +                                               remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> +                                               bus-width = <8>;
> +                                       };
> +                               };
> +                       };
> +
>                         max7310_a: gpio@30 {
>                                 compatible = "maxim,max7310";
>                                 reg = <0x30>;
> @@ -151,6 +166,25 @@
>         };
>  };
>
> +&ipu1_csi0_from_ipu1_csi0_mux {
> +       bus-width = <8>;
> +};
> +
> +&ipu1_csi0_mux_from_parallel_sensor {
> +       remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
> +       bus-width = <8>;
> +};
> +
> +&ipu1_csi0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_ipu1_csi0>;
> +
> +       /* enable frame interval monitor on this port */
> +       fim {
> +               status = "okay";
> +       };

Steve,

You need to remove the fim node now that you've moved this to V4L2 controls.

Regards,

Tim



[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux