This adds documentation of device tree bindings for the STM32 DCMI (Digital Camera Memory Interface). Signed-off-by: Hugues Fruchet <hugues.fruchet@xxxxxx> --- .../devicetree/bindings/media/st,stm32-dcmi.txt | 85 ++++++++++++++++++++++ 1 file changed, 85 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.txt diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt new file mode 100644 index 0000000..8180f63 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt @@ -0,0 +1,85 @@ +STMicroelectronics STM32 Digital Camera Memory Interface (DCMI) + +Required properties: +- compatible: "st,stm32-dcmi" +- reg: physical base address and length of the registers set for the device +- interrupts: should contain IRQ line for the DCMI +- clocks: list of clock specifiers, corresponding to entries in + the clock-names property +- clock-names: must contain "mclk", which is the DCMI peripherial clock +- resets: reference to a reset controller +- reset-names: see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt + +DCMI supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + +Device node example +------------------- + dcmi: dcmi@50050000 { + compatible = "st,stm32-dcmi"; + reg = <0x50050000 0x400>; + interrupts = <78>; + resets = <&rcc STM32F4_AHB2_RESET(DCMI)>; + clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>; + clock-names = "mclk"; + pinctrl-names = "default"; + pinctrl-0 = <&dcmi_pins>; + dmas = <&dma2 1 1 0x414 0x3>; + dma-names = "tx"; + status = "disabled"; + }; + +Board setup example +------------------- +This example is extracted from STM32F429-EVAL board devicetree. +Please note that on this board, the camera sensor reset & power-down +line level are inverted (so reset is active high and power-down is +active low). + +/ { + [...] + clocks { + clk_ext_camera: clk-ext-camera { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + }; + [...] +}; + +&dcmi { + status = "okay"; + + port { + dcmi_0: endpoint@0 { + remote-endpoint = <&ov2640_0>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; +}; + +&i2c@1 { + [...] + ov2640: camera@30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + resetb-gpios = <&stmpegpio 2 GPIO_ACTIVE_HIGH>; + pwdn-gpios = <&stmpegpio 0 GPIO_ACTIVE_LOW>; + clocks = <&clk_ext_camera>; + clock-names = "xvclk"; + status = "okay"; + + port { + ov2640_0: endpoint { + remote-endpoint = <&dcmi_0>; + }; + }; + }; +}; -- 1.9.1