Hello, I have HP/Yuan EC372S DVB-T tuner. I'm trying to make it working under Linux but without success. I've tried using modules from 2.6.31.3 and compiling from Mercurial repository. Just after inserting card (modules have debugging enabled): karaluszek:/lib/modules# dmesg | grep -v '>>>' | grep -v '<<<' | grep -v 'writing to address' | tail -36 [85050.640892] dvb-usb: Yuan EC372S successfully deinitialized and disconnected. [85054.324234] usb 3-3: new high speed USB device using ehci_hcd and address 9 [85054.457258] usb 3-3: New USB device found, idVendor=1164, idProduct=1edc [85054.457269] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [85054.457275] usb 3-3: Product: STK7700D [85054.457280] usb 3-3: Manufacturer: YUANRD [85054.457284] usb 3-3: SerialNumber: 0000000001 [85054.457484] usb 3-3: configuration #1 chosen from 1 choice [85054.458505] FW GET_VERSION length: -32 [85054.458511] cold: 1 [85054.458515] dvb-usb: found a 'Yuan EC372S' in cold state, will try to load a firmware [85054.458522] usb 3-3: firmware: requesting dvb-usb-dib0700-1.20.fw [85054.478061] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw' [85054.684318] dib0700: firmware started successfully. [85055.188223] dvb-usb: found a 'Yuan EC372S' in warm state. [85055.188348] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [85055.188817] DVB: registering new adapter (Yuan EC372S) [85055.236479] ep 0 write error (status = -32, len: 6) [85055.236481] DiB7000P: checking demod on I2C address: 128 (80) [85055.236976] ep 0 read error (status = -32) [85055.236979] I2C read failed on address 0x40 [85055.236981] DiB7000P: i2c read error on 768 [85055.236983] DiB7000P: wrong Vendor ID (read=0x1200) [85055.238348] DiB7000P: checking demod on I2C address: 18 (12) [85055.242480] DiB7000P: setting output mode for demod ffff88007a47b2f0 to 4 [85055.247474] DiB7000P: IC 0 initialized (to i2c_address 0x80) [85055.250101] DiB7000P: setting output mode for demod ffff88007a47b2f0 to 0 [85055.255865] DiB7000P: checking demod on I2C address: 128 (80) [85055.296360] DiB7000P: gpio dir: ffff: val: 0, pwm_pos: ffff [85055.302743] DiB7000P: setting output mode for demod ffff8800300e3000 to 0 [85055.309721] DiB7000P: using default timf [85055.408997] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)... [85055.412746] MT2266: successfully identified [85055.574944] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1d.7/usb3/3-3/input/input19 [85055.575048] dvb-usb: schedule remote query interval to 50 msecs. [85055.575055] dvb-usb: Yuan EC372S successfully initialized and connected. karaluszek:/lib/modules# uname -a Linux karaluszek 2.6.31.3-scibi #1 SMP Sun Oct 11 23:38:13 CEST 2009 x86_64 GNU/Linux After running dvbscan/dvbtune: karaluszek:/home/scibi/dvb/v4l-dvb-f6680fa8e7ec# dvbscan /usr/share/dvb/dvb-t/pl-Warszawa Unable to query frontend status karaluszek:/home/scibi/dvb/v4l-dvb-f6680fa8e7ec# dvbtune -f 690000000 Using DVB card "DiBcom 7000PC" tuning DVB-T (in United Kingdom) to 690000000 Hz polling.... Getting frontend event FE_STATUS: polling.... polling.... ^C [85473.793547] DiB7000P: setting output mode for demod ffff8800300e3000 to 0 [85473.819971] MT2266: set_parms: tune=376832 band=102 UHF [85473.819978] MT2266: set_parms: [1..3]: 0 0 2e [85473.887700] MT2266: Lock when i=3 [85473.913806] DiB7000P: WBD: ref: 3530, sel: 1, active: 0, alpha: 1 [85473.960080] DiB7000P: using default timf [85474.261493] DiB7000P: using default timf [85474.265451] DiB7000P: setting output mode for demod ffff8800300e3000 to 5 [85474.277844] DiB7000P: setting output mode for demod ffff8800300e3000 to 0 [85479.607362] DiB7000P: setting output mode for demod ffff8800300e3000 to 0 [85479.631733] MT2266: set_parms: tune=376832 band=102 UHF [85479.631735] MT2266: set_parms: [1..3]: 0 0 2e [85479.718610] MT2266: Lock when i=4 [85479.772081] DiB7000P: using default timf [85480.073558] DiB7000P: using default timf [85480.077638] DiB7000P: setting output mode for demod ffff8800300e3000 to 5 [85481.083071] DiB7000P: setting output mode for demod ffff8800300e3000 to 0 [85481.107832] MT2266: set_parms: tune=376832 band=102 UHF [85481.107839] MT2266: set_parms: [1..3]: 0 0 2e [85481.179685] MT2266: Lock when i=4 [85481.252064] DiB7000P: using default timf [85481.553570] DiB7000P: using default timf [85481.557560] DiB7000P: setting output mode for demod ffff8800300e3000 to 5 [85482.563011] DiB7000P: setting output mode for demod ffff8800300e3000 to 0 [85482.587880] MT2266: set_parms: tune=376832 band=102 UHF [85482.587887] MT2266: set_parms: [1..3]: 0 0 2e [85482.663631] MT2266: Lock when i=4 [85482.720715] DiB7000P: using default timf [85483.021653] DiB7000P: using default timf [85483.025607] DiB7000P: setting output mode for demod ffff8800300e3000 to 5 [85484.031060] DiB7000P: setting output mode for demod ffff8800300e3000 to 0 [85484.055926] MT2266: set_parms: tune=376832 band=102 UHF [85484.055939] MT2266: set_parms: [1..3]: 0 0 2e [85484.127552] MT2266: Lock when i=4 I've done some usb snooping on Windows using http://sourceforge.net/projects/usbsnoop/ during initialization and start of playback so I can post it here if it's needed. I can also post not filtered dmesg output. karaluszek:/lib/modules# lsusb -s 3:9 -v Bus 003 Device 009: ID 1164:1edc YUAN High-Tech Development Co., Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1164 YUAN High-Tech Development Co., Ltd idProduct 0x1edc bcdDevice 1.00 iManufacturer 1 YUANRD iProduct 2 STK7700D iSerial 3 0000000001 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 46 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 4 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Best regards, Patryk Ściborek -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
