Hi Pavel,
On Sat, Feb 04, 2017 at 10:56:10PM +0100, Pavel Machek wrote:
> Hi!
>
> > > > > +Required properties
> > > > > +===================
> > > > > +
> > > > > +compatible : must contain "video-bus-switch"
> > > >
> > > > How generic is this? Should we have e.g. nokia,video-bus-switch? And if so,
> > > > change the file name accordingly.
> > >
> > > Generic for "single GPIO controls the switch", AFAICT. But that should
> > > be common enough...
> >
> > Um, yes. Then... how about: video-bus-switch-gpio? No Nokia prefix.
>
> Ok, done. I also fixed the english a bit.
>
> > > > > +reg : The interface:
> > > > > + 0 - port for image signal processor
> > > > > + 1 - port for first camera sensor
> > > > > + 2 - port for second camera sensor
> > > >
> > > > I'd say this must be pretty much specific to the one in N900. You could have
> > > > more ports. Or you could say that ports beyond 0 are camera sensors. I guess
> > > > this is good enough for now though, it can be changed later on with the
> > > > source if a need arises.
> > >
> > > Well, I'd say that selecting between two sensors is going to be the
> > > common case. If someone needs more than two, it will no longer be
> > > simple GPIO, so we'll have some fixing to do.
> >
> > It could be two GPIOs --- that's how the GPIO I2C mux works.
> >
> > But I'd be surprised if someone ever uses something like that
> > again. ;-)
>
> I'd say.. lets handle that when we see hardware like that.
Yes. :-)
>
> > > > Btw. was it still considered a problem that the endpoint properties for the
> > > > sensors can be different? With the g_routing() pad op which is to be added,
> > > > the ISP driver (should actually go to a framework somewhere) could parse the
> > > > graph and find the proper endpoint there.
> > >
> > > I don't know about g_routing. I added g_endpoint_config method that
> > > passes the configuration, and that seems to work for me.
> > >
> > > I don't see g_routing in next-20170201 . Is there place to look?
> >
> > I think there was a patch by Laurent to LMML quite some time ago. I suppose
> > that set will be repicked soonish.
> >
> > I don't really object using g_endpoint_config() as a temporary solution; I'd
> > like to have Laurent's opinion on that though. Another option is to wait,
> > but we've already waited a looong time (as in total).
>
> Laurent, do you have some input here? We have simple "2 cameras
> connected to one signal processor" situation here. We need some way of
> passing endpoint configuration from the sensors through the switch. I
> did this:
>
> > > @@ -415,6 +416,8 @@ struct v4l2_subdev_video_ops {
> > > const struct v4l2_mbus_config *cfg);
> > > int (*s_rx_buffer)(struct v4l2_subdev *sd, void *buf,
> > > unsigned int *size);
> > > + int (*g_endpoint_config)(struct v4l2_subdev *sd,
> > > + struct v4l2_of_endpoint *cfg);
>
> Google of g_routing tells me:
>
> 9) Highly reconfigurable hardware - Julien Beraud
>
> - 44 sub-devices connected with an interconnect.
> - As long as formats match, any sub-device could be connected to any
> - other sub-device through a link.
> - The result is 44 * 44 links at worst.
> - A switch sub-device proposed as the solution to model the
> - interconnect. The sub-devices are connected to the switch
> - sub-devices through the hardware links that connect to the
> - interconnect.
> - The switch would be controlled through new IOCTLs S_ROUTING and
> - G_ROUTING.
> - Patches available:
> http://git.linuxtv.org/cgit.cgi/pinchartl/media.git/log/?h=xilinx-wip
>
> but the patches are from 2005. So I guess I'll need some guidance here...
Yeah, that's where it began (2015?), but right now I can only suggest to
wait until there's more. My estimate is within next couple of weeks /
months. But it won't be years.
--
Kind regards,
Sakari Ailus
e-mail: sakari.ailus@xxxxxx XMPP: sailus@xxxxxxxxxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
