On Fri, 2017-01-13 at 11:03 -0800, Steve Longerbeam wrote: > > On 01/13/2017 03:55 AM, Philipp Zabel wrote: > > Am Freitag, den 06.01.2017, 18:11 -0800 schrieb Steve Longerbeam: > >> Add bindings documentation for the i.MX media driver. > >> > >> Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx> > >> --- > >> Documentation/devicetree/bindings/media/imx.txt | 57 +++++++++++++++++++++++++ > >> 1 file changed, 57 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/media/imx.txt > >> > >> diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt > >> new file mode 100644 > >> index 0000000..254b64a > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/media/imx.txt > >> @@ -0,0 +1,57 @@ > >> +Freescale i.MX Media Video Devices > >> + > >> +Video Media Controller node > >> +--------------------------- > >> + > >> +This is the parent media controller node for video capture support. > >> + > >> +Required properties: > >> +- compatible : "fsl,imx-media"; > > Would you be opposed to calling this "capture-subsystem" instead of > > "imx-media"? We already use "fsl,imx-display-subsystem" and > > "fsl,imx-gpu-subsystem" for the display and GPU compound devices. > > sure. Some pie-in-the-sky day when DRM and media are unified, > there could be a single device that handles them all, Indeed :) > but for now > I'm fine with "fsl,capture-subsystem". Actually, I meant fsl,imx-capture-subsystem. fsl,imx-media-subsystem would be fine, too. Either way, I'll be happy if it looks similar to the other two. [...] > > This is a clever method to get better frame timestamps. Too bad about > > the routing requirements. Can this be used on Nitrogen6X? > > Absolutely, this support just needs use of the input-capture channels in the > imx GPT. I still need to submit the patch to the imx-gpt driver that adds an > input capture API, so at this point fsl,input-capture-channel has no effect, > but it does work (tested on SabreAuto). Nice. [...] > >> +Required properties: > >> +- compatible : "fsl,imx6-mipi-csi2"; > > I think this should get an additional "snps,dw-mipi-csi2" compatible, > > since the only i.MX6 specific part is the bolted-on IPU2CSI gasket. > > right, minus the gasket it's a Synopsys core. I'll add that compatible flag. > Or should wait until the day this subdev is exported for general use, after > pulling out the gasket specifics? It can be added right away. > >> +- reg : physical base address and length of the register set; > >> +- clocks : the MIPI CSI-2 receiver requires three clocks: hsi_tx > >> + (the DPHY clock), video_27m, and eim_sel; > > Note that hsi_tx is incorrectly named. CCGR3[CG8] just happens to be the > > shared gate bit that gates the HSI clocks as well as the MIPI > > "ac_clk_125m", "cfg_clk", "ips_clk", and "pll_refclk" inputs to the mipi > > csi-2 core, but we are missing shared gate clocks in the clock tree for > > these. > > Yes, so many clocks for the MIPI core. Why so many? I would think > there would need to be at most three: a clock for the MIPI CSI-2 core > and HSI core, and a clock for the D-PHY (oh and maybe a clock for an > M-PHY if there is one). I have no clue what all these other clocks are. > But anyway, a single gating bit, CCGR3[CG8], seems to enable them all. I would imagine the CSI-2 core has a high-speed clock input from the D-PHY for serial input, an APB clock for register access (ips_clk), and a pixel clock input for the parallel output (pixel_clk), at least. The D-PHY will have a PLL reference input (pll_refclk?) and probably its own register clock (cfg_clk?). I've looked at the MIPI DSI chapter, and it looks like ac_clk_125m is used for DSI only. > > Both cfg_clk and pll_refclk are sourced from video_27m, so "cfg" -> > > video_27m seems fine. > > But I don't get "dphy". > > I presume it's the clock for the D-PHY. > > > Which input clock would that correspond to? > > "pll_refclk?" > > the mux at CDCDR says it comes from PLL3_120M, or PLL2_PFD2. I think that makes sense. regards Philipp -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
