On 01/03/2017 10:57 PM, Steve Longerbeam wrote:
> Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
>
> The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
>
> The OV5640 connects to the input port on the MIPI CSI-2 receiver on
> mipi_csi. It is set to transmit over MIPI virtual channel 1.
>
> Until the OV5652 sensor module compatible with the SabreSD becomes
> available for testing, the ov5642 node is currently disabled.
>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
> ---
[snip]
> +
> + camera: ov5642@3c {
ov5642: camera@3c
> + compatible = "ovti,ov5642";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ov5642>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + clock-names = "xclk";
> + reg = <0x3c>;
> + xclk = <24000000>;
> + DOVDD-supply = <&vgen4_reg>; /* 1.8v */
> + AVDD-supply = <&vgen5_reg>; /* 2.8v, rev C board is VGEN3
> + rev B board is VGEN5 */
> + DVDD-supply = <&vgen2_reg>; /* 1.5v*/
> + pwdn-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* SD1_DAT0 */
> + reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; /* SD1_DAT1 */
Comments about SD1_* pad names are redundant.
> + status = "disabled";
Why is it disabled here?
> +
> + port {
> + ov5642_to_ipu1_csi0_mux: endpoint {
> + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> + bus-width = <8>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + };
> + };
> + };
> };
>
> &i2c2 {
> @@ -322,6 +376,34 @@
> };
> };
> };
> +
> + mipi_camera: ov5640@3c {
ov5640: camera@3c
> + compatible = "ovti,ov5640_mipi";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ov5640>;
> + reg = <0x3c>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + clock-names = "xclk";
> + xclk = <24000000>;
> + DOVDD-supply = <&vgen4_reg>; /* 1.8v */
> + AVDD-supply = <&vgen5_reg>; /* 2.8v, rev C board is VGEN3
> + rev B board is VGEN5 */
> + DVDD-supply = <&vgen2_reg>; /* 1.5v*/
> + pwdn-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; /* SD1_DAT2 */
> + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; /* SD1_CLK */
Comments about SD1_* pad names are redundant.
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ov5640_to_mipi_csi: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&mipi_csi_from_mipi_sensor>;
> + data-lanes = <0 1>;
> + clock-lanes = <2>;
> + };
> + };
> + };
> };
>
> &i2c3 {
> @@ -426,6 +508,36 @@
> >;
> };
>
> + pinctrl_ov5640: ov5640grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x80000000
> + MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x80000000
> + >;
> + };
> +
> + pinctrl_ov5642: ov5642grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x80000000
> + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x80000000
> + >;
> + };
> +
> + pinctrl_ipu1_csi0: ipu1grp-csi0 {
Please rename the node name to ipu1csi0grp.
Please add new pin control groups preserving the alphanimerical order.
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000
> + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000
> + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000
> + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000
> + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000
> + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000
> + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000
> + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000
> + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000
> + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000
> + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000
> + >;
> + };
> +
> pinctrl_pcie: pciegrp {
> fsl,pins = <
> MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
>
--
With best wishes,
Vladimir
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
