Hi there, with kernel 2.6.30.8 my "TwinhanDTV USB-Ter USB1.1 / Magic Box I" worked. Now with kernel 2.6.32-rc3 (and 2.6.31.1) the modules seems to be loaded fine, but tzap/kaffeine/mplayer can not tune to a channel: dmesg says: dvb-usb: found a 'TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device' in warm state. dvb-usb: will use the device's hardware PID filter (table count: 16). DVB: registering new adapter (TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device) DVB: registering adapter 0 frontend 0 (DiBcom 3000M-B DVB-T)... dibusb: This device has the Thomson Cable onboard. Which is default. input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:04.0/usb4/4-2/input/input5 dvb-usb: schedule remote query interval to 150 msecs. dvb-usb: TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device successfully initialized and connected. usbcore: registered new interface driver dvb_usb_dibusb_mb grep DVB .config says (no chaanges between 2.6.30.8 and 2.6.32-rc3): CONFIG_DVB_CORE=m CONFIG_DVB_MAX_ADAPTERS=8 CONFIG_DVB_CAPTURE_DRIVERS=y CONFIG_DVB_USB=m CONFIG_DVB_USB_DIBUSB_MB=m CONFIG_DVB_DIB3000MB=m CONFIG_DVB_PLL=m lsmod |grep dvb dvb_usb_dibusb_mb 16715 0 dvb_usb_dibusb_common 3559 1 dvb_usb_dibusb_mb dvb_pll 8604 1 dvb_usb_dibusb_mb dib3000mb 10969 1 dvb_usb_dibusb_mb dvb_usb 13737 2 dvb_usb_dibusb_mb,dvb_usb_dibusb_common dvb_core 85727 1 dvb_usb tzap arte -r using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' reading channels from file '/home/grafrotz/.tzap/channels.conf' tuning to 602000000 Hz video pid 0x00c9, audio pid 0x00ca status 00 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 00 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 00b2 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff | and so on. The signal-values are zero or near zero, but when i boot the old kernel 2.6.30.8, t can tune without problems. kaffeine DVB says: Using DVB device 0:0 "DiBcom 3000M-B DVB-T" tuning DVB-T to 602000000 Hz inv:2 bw:0 fecH:2 fecL:9 mod:1 tm:1 gi:3 hier:0 ................ Not able to lock to the signal on the given frequency Frontend closed Tuning delay: 2611 ms mplayer dvb://arte says: MPlayer SVN-r29699-4.4.1 (C) 2000-2009 MPlayer Team Spiele dvb://arte. dvb_tune Freq: 602000000 Not able to lock to the signal on the given frequency, timeout: 30 dvb_tune, TUNING FAILED ERROR, COULDN'T SET CHANNEL 13: Konnte 'dvb://arte' nicht öffnen. Beenden... (Dateiende erreicht) Greetings Mario -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
