Hi Rob,
On Saturday 08 Oct 2016 20:29:39 Rob Herring wrote:
> On Tue, Oct 04, 2016 at 07:23:29PM +0300, Laurent Pinchart wrote:
> > LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A.
> > Multiple incompatible data link layers have been used over time to
> > transmit image data to LVDS panels. This binding supports display panels
> > compatible with the JEIDA-59-1999, Open-LDI and VESA SWPG
> > specifications.
> >
> > Signed-off-by: Laurent Pinchart
> > <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
> > ---
> >
> > .../bindings/display/panel/panel-lvds.txt | 119 ++++++++++++++++
> > 1 file changed, 119 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/display/panel/panel-lvds.txt>
> > diff --git
> > a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
> > b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt new file
> > mode 100644
> > index 000000000000..250861f2673e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
> > @@ -0,0 +1,119 @@
> > +Generic LVDS Panel
> > +==================
> > +
> > +LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A.
> > Multiple
> > +incompatible data link layers have been used over time to transmit image
> > data
> > +to LVDS panels. This bindings supports display panels compatible with the
> > +following specifications.
> > +
> > +[JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999,
> > February
> > +1999 (Version 1.0), Japan Electronic Industry Development Association
> > (JEIDA)
> > +[LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National
> > +Semiconductor
> > +[VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video
> > +Electronics Standards Association (VESA)
> > +
> > +Device compatible with those specifications have been marketed under the
> > +FPD-Link and FlatLink brands.
> > +
> > +
> > +Required properties:
> > +- compatible: shall contain "panel-lvds"
>
> Maybe as a fallback, but on its own, no way.
Which brings an interesting question: when designing generic DT bindings,
what's the rule regarding
> > +- width-mm: panel display width in millimeters
> > +- height-mm: panel display height in millimeters
>
> This is already documented for all panels IIRC.
Note that this DT binding has nothing to do with the simple-panel binding. It
is instead similar to the panel-dpi and panel-dsi-cm bindings (which currently
don't but should specify the panel size in DT). The LVDS panel driver will
*not* include any panel-specific information such as size or timings, these
are specified in DT.
> > +- data-mapping: the color signals mapping order, "jeida-18", "jeida-24"
> > + or "vesa-24"
>
> Maybe this should be part of the compatible.
I've thought about it, but given that some panels support selecting between
multiple modes (through a mode pin that is usually hardwired), I believe a
separate DT property makes sense.
Furthermore, LVDS data organization is controlled by the combination of both
data-mapping and data-mirror. It makes little sense from my point of view to
handle one as part of the compatible string and the other one as a separate
property.
> > +Optional properties:
> > +- label: a symbolic name for the panel
>
> Could be for any panel or display connector.
Yes, but I'm not sure to understand how that's relevant :-)
> > +- avdd-supply: reference to the regulator that powers the panel
> analog supply
> > +- dvdd-supply: reference to the regulator that powers the panel digital
> > supply
>
> Which one has to be powered on first, what voltage, and with what time
> in between? This is why "generic" or "simple" bindings don't work.
The above-mentioned specifications also define connectors, pinouts and power
supplies, but many LVDS panels compatible with the LVDS physical and data
layers use a different connector with small differences in power supplies.
I believe the voltage is irrelevant here, it doesn't need to be controlled by
the operating system. Power supplies order and timing is relevant, I'll
investigate the level of differences between panels. I'm also fine with
dropping those properties for now.
> > +- data-mirror: if set, reverse the bit order on all data lanes (6 to 0
> > instead
> > + of 0 to 6)
> > +
> > +Required nodes:
> > +- One "panel-timing" node containing video timings, in accordance with
> > the
> > + display timing bindings defined in
> > + Documentation/devicetree/bindings/display/display-timing.txt.
>
> I'll let Thierry comment on this one.
>
> > +- One "port" child node for the LVDS input port, in accordance with the
> > + video interface bindings defined in
> > + Documentation/devicetree/bindings/media/video-interfaces.txt.
> > +
> > +
> > +LVDS data mappings are defined as follows.
> > +
> > +- "jeida-18" - 18-bit data mapping compatible with the [JEIDA], [LDI] and
> > + [VESA] specifications. Data are transferred as follows on 3 LVDS lanes.
> > +
> > +Slot 0 1 2 3 4 5 6
> > + ________________ _________________
> > +Clock \_______________________/
> > + ______ ______ ______ ______ ______ ______ ______
> > +DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__><
> > +DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__><
> > +DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__><
> > +
> > +- "jeida-24" - 24-bit data mapping compatible with the [DSIM] and [LDI]
> > + specifications. Data are transferred as follows on 4 LVDS lanes.
> > +
> > +Slot 0 1 2 3 4 5 6
> > + ________________ _________________
> > +Clock \_______________________/
> > + ______ ______ ______ ______ ______ ______ ______
> > +DATA0 ><__G2__><__R7__><__R6__><__R5__><__R4__><__R3__><__R2__><
> > +DATA1 ><__B3__><__B2__><__G7__><__G6__><__G5__><__G4__><__G3__><
> > +DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B7__><__B6__><__B5__><__B4__><
> > +DATA3 ><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__><
> > +
> > +- "vesa-24" - 24-bit data mapping compatible with the [VESA]
> > specification. + Data are transferred as follows on 4 LVDS lanes.
> > +
> > +Slot 0 1 2 3 4 5 6
> > + ________________ _________________
> > +Clock \_______________________/
> > + ______ ______ ______ ______ ______ ______ ______
> > +DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__><
> > +DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__><
> > +DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__><
> > +DATA3 ><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__><
> > +
> > +
> > +Control signals are mapped as follows.
> > +
> > +CTL0: HSync
> > +CTL1: VSync
> > +CTL2: Data Enable
> > +CTL3: 0
> > +
> > +
> > +Example
> > +-------
> > +
> > +panel {
> > + compatible = "mitsubishi,aa121td01", "panel-lvds";
> > + label = "lcd";
>
> Kind of useless in your example.
I can rename that to "LCD0" for instance.
> > +
> > + width-mm = <261>;
> > + height-mm = <163>;
> > +
> > + data-mapping = "jeida-24";
> > +
> > + panel-timing {
> > + /* 1280x800 @60Hz */
> > + clock-frequency = <71000000>;
> > + hactive = <1280>;
> > + vactive = <800>;
> > + hsync-len = <70>;
> > + hfront-porch = <20>;
> > + hback-porch = <70>;
> > + vsync-len = <5>;
> > + vfront-porch = <3>;
> > + vback-porch = <15>;
> > + };
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&lvds_connector>;
> > + };
> > + };
> > +};
--
Regards,
Laurent Pinchart
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
