Defines the host video capture device node and the ADV7180 decoder
sensor. The host capture device connects to the ADV7180 via the
parallel-bus mux input on the ipu1_csi0_mux.
On the sabreauto, two analog video inputs are routed to the ADV7180,
composite on Ain1, and composite on Ain3. Those inputs are defined
via inputs and input-names under the endpoint node
ipu1_csi0_from_ipu1_csi0_mux. The ADV7180 power pin is via max7310_b
port expander.
Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
---
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 68 ++++++++++++++++++++++++++++++++
1 file changed, 68 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 737bb54..ec952b1 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -147,10 +147,54 @@
gpio-controller;
#gpio-cells = <2>;
};
+
+ camera: adv7180@21 {
+ compatible = "adi,adv7180";
+ reg = <0x21>;
+ pwdn-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <27 0x8>;
+
+ port {
+ adv7180_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <8>;
+ };
+ };
+ };
+ };
+ };
+
+ ipucap0: ipucap0 {
+ compatible = "fsl,imx-video-capture";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ ports = <&ipu1_csi0>;
+ status = "okay";
+
+ fim {
+ enable = <1>;
};
};
};
+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <8>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
+ inputs = <0x00 0x02>;
+ input-names = "ADV7180 Composite on Ain1",
+ "ADV7180 Composite on Ain3";
+};
+
+&ipu1_csi0_mux {
+ status = "okay";
+};
+
&clks {
assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
<&clks IMX6QDL_PLL4_BYPASS>,
@@ -450,6 +494,30 @@
>;
};
+ pinctrl_ipu1_csi0: ipu1grp-csi0 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04 0x80000000
+ MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05 0x80000000
+ MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06 0x80000000
+ MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07 0x80000000
+ MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08 0x80000000
+ MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09 0x80000000
+ MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10 0x80000000
+ MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11 0x80000000
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000
+ >;
+ };
+
pinctrl_pwm3: pwm1grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
