Defines the host ipu-capture device node and two camera sensors:
parallel-bus OV5642 and MIPI CSI-2 OV5640.
The host capture device connects to the OV5642 via the parallel-bus
mux input on the ipu1_csi0_mux.
The host capture device connects to the OV5640 via the MIPI CSI-2
receiver (directly on virtual channel 1 to ipu1_csi1 on imx6q, and
indirectly via the ipu1_csi1_mux on imx6dl).
Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
---
arch/arm/boot/dts/imx6dl-sabresd.dts | 44 +++++++++++
arch/arm/boot/dts/imx6q-sabresd.dts | 16 ++++
arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 139 ++++++++++++++++++++++++++++++++-
3 files changed, 198 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6dl-sabresd.dts b/arch/arm/boot/dts/imx6dl-sabresd.dts
index 1e45f2f..0a4bfc2 100644
--- a/arch/arm/boot/dts/imx6dl-sabresd.dts
+++ b/arch/arm/boot/dts/imx6dl-sabresd.dts
@@ -15,3 +15,47 @@
model = "Freescale i.MX6 DualLite SABRE Smart Device Board";
compatible = "fsl,imx6dl-sabresd", "fsl,imx6dl";
};
+
+&ipu1_csi1_from_ipu1_csi1_mux {
+ data-lanes = <0 1>;
+ clock-lanes = <2>;
+};
+
+&ipu1_csi1_mux {
+ status = "okay";
+};
+
+/*
+ * if the OV5642 sensor is enabled, the ipu1_csi0_mux is also enabled,
+ * but we don't want to find the OV5640 through ipu1_csi0_mux path to the
+ * mipi-csi2 receiver, so shutdown the link to the mipi-csi2 receiver at
+ * all virtual channels.
+*/
+#ifdef __ENABLE_OV5642__
+&ipu1_csi0_mux_from_mipi_vc0 {
+ remote-endpoint = <>;
+};
+&ipu1_csi0_mux_from_mipi_vc1 {
+ remote-endpoint = <>;
+};
+&ipu1_csi0_mux_from_mipi_vc2 {
+ remote-endpoint = <>;
+};
+&ipu1_csi0_mux_from_mipi_vc3 {
+ remote-endpoint = <>;
+};
+#endif
+
+/*
+ * shutdown links to mipi-csi2 channels 0,2,3 through ipu1_csi1_mux. The
+ * OV5640 is on VC1, so it must be found only on that ipu1_csi1_mux input.
+ */
+&ipu1_csi1_mux_from_mipi_vc0 {
+ remote-endpoint = <>;
+};
+&ipu1_csi1_mux_from_mipi_vc2 {
+ remote-endpoint = <>;
+};
+&ipu1_csi1_mux_from_mipi_vc3 {
+ remote-endpoint = <>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabresd.dts b/arch/arm/boot/dts/imx6q-sabresd.dts
index 9cbdfe7..ade6305 100644
--- a/arch/arm/boot/dts/imx6q-sabresd.dts
+++ b/arch/arm/boot/dts/imx6q-sabresd.dts
@@ -23,3 +23,19 @@
&sata {
status = "okay";
};
+
+&ipu1_csi1_from_mipi_vc1 {
+ data-lanes = <0 1>;
+ clock-lanes = <2>;
+};
+
+/*
+ * if the OV5642 sensor is enabled, the ipu1_csi0_mux is also enabled,
+ * but we don't want to find the OV5640 through ipu1_csi0_mux path, so
+ * shutdown the link to the mipi-csi2 receiver.
+*/
+#ifdef __ENABLE_OV5642__
+&ipu1_csi0_mux_from_mipi_vc0 {
+ remote-endpoint = <>;
+};
+#endif
diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 5248e7b..ce575e6 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -10,6 +10,10 @@
* http://www.gnu.org/copyleft/gpl.html
*/
+/* Uncomment to enable parallel interface OV5642 on i2c1 and port csi0 */
+/* #define __ENABLE_OV5642__ */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
@@ -144,6 +148,54 @@
};
};
};
+
+#ifdef __ENABLE_OV5642__
+ ipucap0: ipucap@0 {
+ compatible = "fsl,imx-video-capture";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ ports = <&ipu1_csi0>;
+ status = "okay";
+ };
+#endif
+
+ ipucap1: ipucap@1 {
+ compatible = "fsl,imx-video-capture";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ports = <&ipu1_csi1>;
+ status = "okay";
+ };
+};
+
+#ifdef __ENABLE_OV5642__
+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <8>;
+ data-shift = <12>; /* Lines 19:12 used */
+ hsync-active = <1>;
+ vsync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0_mux {
+ status = "okay";
+};
+#endif
+
+&mipi_csi {
+ status = "okay";
+};
+
+/* Incoming port from sensor */
+&mipi_csi_from_mipi_sensor {
+ remote-endpoint = <&ov5640_to_mipi_csi>;
+ data-lanes = <0 1>;
+ clock-lanes = <2>;
};
&audmux {
@@ -214,7 +266,34 @@
0x8014 /* 4:FN_DMICCDAT */
0x0000 /* 5:Default */
>;
- };
+ };
+
+#ifdef __ENABLE_OV5642__
+ camera: ov5642@3c {
+ compatible = "ovti,ov5642";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5642>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ reg = <0x3c>;
+ xclk = <24000000>;
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen5_reg>; /* 2.8v, rev C board is VGEN3
+ rev B board is VGEN5 */
+ DVDD-supply = <&vgen2_reg>; /* 1.5v*/
+ pwdn-gpios = <&gpio1 16 1>; /* SD1_DAT0 */
+ reset-gpios = <&gpio1 17 0>; /* SD1_DAT1 */
+
+ port {
+ ov5642_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+#endif
};
&i2c2 {
@@ -322,6 +401,34 @@
};
};
};
+
+ mipi_camera: ov5640@3c {
+ compatible = "ovti,ov5640_mipi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x3c>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ xclk = <24000000>;
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen5_reg>; /* 2.8v, rev C board is VGEN3
+ rev B board is VGEN5 */
+ DVDD-supply = <&vgen2_reg>; /* 1.5v*/
+ pwdn-gpios = <&gpio1 19 0>; /* SD1_DAT2 */
+ reset-gpios = <&gpio1 20 1>; /* SD1_CLK */
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ov5640_to_mipi_csi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&mipi_csi_from_mipi_sensor>;
+ data-lanes = <0 1>;
+ clock-lanes = <2>;
+ };
+ };
+ };
};
&i2c3 {
@@ -426,6 +533,36 @@
>;
};
+ pinctrl_ov5640: ov5640grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x80000000
+ MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x80000000
+ >;
+ };
+
+ pinctrl_ov5642: ov5642grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x80000000
+ MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x80000000
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1grp-csi0 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000
+ >;
+ };
+
pinctrl_pcie: pciegrp {
fsl,pins = <
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
