Hello. I have the Terratec Cinergy Hybrid T XS USB (em2882) - usb-id 0ccd:005e. It works with Marcus Rechberger's em28xx-new driver, but since that code is unmaintained now, I tested this device with v4l-dvb today. The analog picture is there, but audio is very, very quiet, almost not there. Is there some way to increase the volume? Second question, what would be required to get DVB working? The final thing is not a question, it's actually something that works: the remote. It's the same one as comes with the other Hybrid XS (0ccd:0042), adding these two lines to the definition of this card in em28xx-cards.c makes it work: .ir_codes = &ir_codes_terratec_cinergy_xs_table, .xclk = EM28XX_XCLK_FREQUENCY_12MHZ, Any pointers to solving my issues (analog audio, dvb) appreciated. I can test patches, I can give ssh access to my machine if it helps. There's even a Windows install on this machine, so USB sniffing of the Windows driver is possible, I just need instructions on what exactly to do. Dmesg output for this device is attached. Regards, Uroš
usb 1-4: new high speed USB device using ehci_hcd and address 6 usb 1-4: configuration #1 chosen from 1 choice Linux video capture interface: v2.00 em28xx: New device TerraTec Electronic GmbH Cinergy Hybrid T USB XS (2882) @ 480 Mbps (0ccd:005e, interface 0, class 0) em28xx #0: chip ID is em2882/em2883 em28xx #0: i2c eeprom 00: 1a eb 67 95 cd 0c 5e 00 d0 12 5c 03 9e 40 de 1c em28xx #0: i2c eeprom 10: 6a 34 27 57 46 07 01 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 31 00 b8 00 14 00 5b 1e 00 00 em28xx #0: i2c eeprom 30: 00 00 20 40 20 6e 02 20 10 01 00 00 00 00 00 00 em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 34 03 54 00 65 00 em28xx #0: i2c eeprom 70: 72 00 72 00 61 00 54 00 65 00 63 00 20 00 45 00 em28xx #0: i2c eeprom 80: 6c 00 65 00 63 00 74 00 72 00 6f 00 6e 00 69 00 em28xx #0: i2c eeprom 90: 63 00 20 00 47 00 6d 00 62 00 48 00 00 00 40 03 em28xx #0: i2c eeprom a0: 43 00 69 00 6e 00 65 00 72 00 67 00 79 00 20 00 em28xx #0: i2c eeprom b0: 48 00 79 00 62 00 72 00 69 00 64 00 20 00 54 00 em28xx #0: i2c eeprom c0: 20 00 55 00 53 00 42 00 20 00 58 00 53 00 20 00 em28xx #0: i2c eeprom d0: 28 00 32 00 38 00 38 00 32 00 29 00 00 00 1c 03 em28xx #0: i2c eeprom e0: 30 00 36 00 30 00 39 00 30 00 32 00 30 00 31 00 em28xx #0: i2c eeprom f0: 33 00 38 00 34 00 33 00 00 00 00 00 00 00 00 00 em28xx #0: EEPROM ID= 0x9567eb1a, EEPROM hash = 0x7713bfbe em28xx #0: EEPROM info: em28xx #0: AC97 audio (5 sample rates) em28xx #0: 500mA max power em28xx #0: Table at 0x27, strings=0x409e, 0x1cde, 0x346a em28xx #0: Identified as Terratec Hybrid XS (em2882) (card=55) em28xx #0: em28xx #0: The support for this board weren't valid yet. em28xx #0: Please send a report of having this working em28xx #0: not to V4L mailing list (and/or to other addresses) tvp5150 4-005c: chip found @ 0xb8 (em28xx #0) tuner 4-0061: chip found @ 0xc2 (em28xx #0) xc2028 4-0061: creating new instance xc2028 4-0061: type set to XCeive xc2028/xc3028 tuner usb 1-4: firmware: requesting xc3028-v27.fw xc2028 4-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7 xc2028 4-0061: Loading firmware for type=BASE (1), id 0000000000000000. xc2028 4-0061: Loading firmware for type=(0), id 000000000000b700. SCODE (20000000), id 000000000000b700: xc2028 4-0061: Loading SCODE for type=MONO SCODE HAS_IF_4320 (60008000), id 0000000000008000. em28xx #0: Config register raw data: 0xd0 em28xx #0: AC97 vendor ID = 0xffffffff em28xx #0: AC97 features = 0x6a90 em28xx #0: Empia 202 AC97 audio processor detected tvp5150 4-005c: tvp5150am1 detected. em28xx #0: v4l2 driver version 0.1.2 em28xx #0: V4L2 device registered as /dev/video0 and /dev/vbi0 usbcore: registered new interface driver em28xx em28xx driver loaded em28xx-audio.c: probing for em28x1 non standard usbaudio em28xx-audio.c: Copyright (C) 2006 Markus Rechberger Em28xx: Initialized (Em28xx Audio Extension) extension tvp5150 4-005c: tvp5150am1 detected. xc2028 4-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. xc2028 4-0061: Loading firmware for type=(0), id 0000000100000007. xc2028 4-0061: Loading SCODE for type=MONO SCODE HAS_IF_5320 (60008000), id 0000000f00000007.
