(EC168) PC Basic TNT USB Basic V5 ( France ) recognized but no channel tuning

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello
I've just bough that and it seems that the EC168 driver can't work with
it ( yet )
The PCB identifies itself as a ForwardVideo "EzTV818_D.". Work with a
EC168 and a MXL5003S ( no doubt about it, but it is barely legible, and
since i've no camera, no PCB picture available ). ( and the EC168BDA.bin
firmware is provided on the CD )

A typical dmesg for it :


[19715.764919] usb 2-1.1: new high speed USB device using ehci_hcd and
address 8
[19715.873356] usb 2-1.1: configuration #1 chosen from 1 choice
[19715.878085] dvb-usb: found a 'E3C EC168 DVB-T USB2.0 reference
design' in cold state, will try to load a firmware
[19715.878096] firmware: requesting dvb-usb-ec168.fw
[19715.929889] dvb-usb: downloading firmware from file 'dvb-usb-ec168.fw'
[19715.985884] dvb-usb: found a 'E3C EC168 DVB-T USB2.0 reference
design' in warm state.
[19715.985958] dvb-usb: will pass the complete MPEG2 transport stream to
the software demuxer.
[19715.986487] DVB: registering new adapter (E3C EC168 DVB-T USB2.0
reference design)
[19715.986931] DVB: registering adapter 1 frontend 0 (E3C EC100 DVB-T)...
[19715.987045] MXL5005S: Attached at address 0xc6
[19715.987052] dvb-usb: E3C EC168 DVB-T USB2.0 reference design
successfully initialized and connected.
[19716.004730] dvb-usb: found a 'E3C EC168 DVB-T USB2.0 reference
design' in warm state.
[19716.004799] dvb-usb: will pass the complete MPEG2 transport stream to
the software demuxer.
[19716.010131] DVB: registering new adapter (E3C EC168 DVB-T USB2.0
reference design)
[19716.010499] DVB: registering adapter 2 frontend 0 (E3C EC100 DVB-T)...
[19716.010612] MXL5005S: Attached at address 0xc6
[19716.010619] dvb-usb: E3C EC168 DVB-T USB2.0 reference design
successfully initialized and connected.
[19716.010729] usb 2-1.1: New USB device found, idVendor=18b4,
idProduct=1001
[19716.010733] usb 2-1.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0

To be perfectly honest a previous attempt didn't have the "New USB
device" at the end, but the result was the same : no tuning possible (
"WARNING: >>> tuning failed!!!" ) even if there is a device file for it
in /dev/ ( on a Linux debian 2.6.26-2-686 #1 SMP Fri Aug 14 01:27:18 UTC
2009 i686 GNU/Linux with V4L/DVB driver using mercurial ). I've checked
the antenna cable  ( my old Intuix S800 work perfectly in the same setup
but it does not have a remote :) )


Thanks for any info/tips.



--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux