Devin Heitmueller wrote:
On Sun, Jul 19, 2009 at 9:15 AM, Mark Lord<lkml@xxxxxx> wrote:
..
The mythbackend (recording) program tunes/records fine with it,
but any attempt to watch "Live TV" via mythfrontend just locks
up the UI for 30 seconds or so, and then it reverts to the menus.
..
Could you please provide the following:
1. Exactly which product you are using (including the USB/PCI id)
..
Doh! Yes, of course!
It's the popular Hauppauge HVR-950Q USB Stick:
Bus 007 Device 006: ID 2040:7200 Hauppauge
3. Whether you are using the device for digital, analog, or both, and
which the mythtv attempted to use when running the mythfrontend.
..
Digital-only, since the tuner stick has never worked (and still doesn't)
for analog NTSC with MythTV-0.21-fixes. That's okay, I really only use
it for digital ATSC over-the-air (OTA) reception.
2. dmesg output from the time the card is inserted (or booted up if
PCI) to the time *after* you attempted to use the frontend with mythtv.
The remainder of this email contains (only) the dmesg output.
Thanks.
rocessor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5319.72 BogoMIPS (lpj=2659862)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
mce: CPU supports 6 MCE banks
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (10639.55 BogoMIPS).
NET: Registered protocol family 16
ACPI: bus type pci registered
dca service started, version 1.8
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0xfc00-0xfc1f]
pci 0000:00:1a.1: reg 20 io port: [0xf800-0xf81f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xfdfff000-0xfdfff3ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xfdff4000-0xfdff7fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xf400-0xf41f]
pci 0000:00:1d.1: reg 20 io port: [0xf000-0xf01f]
pci 0000:00:1d.2: reg 20 io port: [0xec00-0xec1f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xfdffe000-0xfdffe3ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 003f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 003f)
pci 0000:00:1f.2: reg 10 io port: [0xe800-0xe807]
pci 0000:00:1f.2: reg 14 io port: [0xe400-0xe403]
pci 0000:00:1f.2: reg 18 io port: [0xe000-0xe007]
pci 0000:00:1f.2: reg 1c io port: [0xdc00-0xdc03]
pci 0000:00:1f.2: reg 20 io port: [0xd800-0xd81f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfdffd000-0xfdffd7ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 32bit mmio: [0xfdffc000-0xfdffc0ff]
pci 0000:00:1f.3: reg 20 io port: [0x500-0x51f]
pci 0000:00:1f.6: reg 10 64bit mmio: [0xfdffb000-0xfdffbfff]
pci 0000:01:00.0: reg 10 32bit mmio: [0xfa000000-0xfaffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xf8000000-0xf9ffffff]
pci 0000:01:00.0: reg 24 io port: [0x5c00-0x5c7f]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x07ffff]
pci 0000:00:01.0: bridge io port: [0x5000-0x5fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xf8000000-0xfbffffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:00:1c.0: bridge io port: [0xa000-0xafff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xfdc00000-0xfdcfffff]
pci 0000:00:1c.0: bridge 64bit mmio pref: [0xfdb00000-0xfdbfffff]
pci 0000:04:00.0: reg 10 64bit mmio: [0xfdefc000-0xfdefffff]
pci 0000:04:00.0: reg 18 io port: [0x6c00-0x6cff]
pci 0000:04:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:04:00.0: supports D1 D2
pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:00:1c.3: bridge io port: [0x6000-0x6fff]
pci 0000:00:1c.3: bridge 32bit mmio: [0xfde00000-0xfdefffff]
pci 0000:00:1c.3: bridge 64bit mmio pref: [0xfdd00000-0xfddfffff]
pci 0000:05:00.0: reg 10 32bit mmio: [0xdbfff000-0xdbfff7ff]
pci 0000:05:00.0: reg 14 io port: [0x7c00-0x7c7f]
pci 0000:05:00.0: supports D2
pci 0000:05:00.0: PME# supported from D2 D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:05:02.0: reg 10 32bit mmio: [0xf4000000-0xf7ffffff]
pci 0000:05:03.0: reg 10 32bit mmio: [0xd4000000-0xd7ffffff]
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0x7000-0x7fff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xd4000000-0xdbffffff]
pci 0000:00:1e.0: bridge 64bit mmio pref: [0xf4000000-0xf7ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 9 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 5 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 5 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs *5 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 9 10 11 12 14 *15)
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x290-0x29f has been reserved
system 00:01: ioport range 0x800-0x87f has been reserved
system 00:01: ioport range 0x880-0x88f has been reserved
system 00:0a: ioport range 0x400-0x4bf could not be reserved
system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0d: iomem range 0xd3000-0xd3fff has been reserved
system 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
system 00:0d: iomem range 0xfc000-0xfffff could not be reserved
system 00:0d: iomem range 0x7ff00000-0x7fffffff could not be reserved
system 00:0d: iomem range 0xfed00000-0xfed000ff has been reserved
system 00:0d: iomem range 0x7fee0000-0x7fefffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0x100000-0x7fedffff could not be reserved
system 00:0d: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0d: iomem range 0xfed13000-0xfed1ffff has been reserved
system 00:0d: iomem range 0xfed20000-0xfed9ffff has been reserved
system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0d: iomem range 0xffb00000-0xffb7ffff has been reserved
system 00:0d: iomem range 0xfff00000-0xffffffff has been reserved
system 00:0d: iomem range 0xe0000-0xeffff has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x5000-0x5fff
pci 0000:00:01.0: MEM window: 0xf8000000-0xfbffffff
pci 0000:00:01.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: 0xa000-0xafff
pci 0000:00:1c.0: MEM window: 0xfdc00000-0xfdcfffff
pci 0000:00:1c.0: PREFETCH window: 0x000000fdb00000-0x000000fdbfffff
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.3: IO window: 0x6000-0x6fff
pci 0000:00:1c.3: MEM window: 0xfde00000-0xfdefffff
pci 0000:00:1c.3: PREFETCH window: 0x000000fdd00000-0x000000fddfffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
pci 0000:00:1e.0: IO window: 0x7000-0x7fff
pci 0000:00:1e.0: MEM window: 0xd4000000-0xdbffffff
pci 0000:00:1e.0: PREFETCH window: 0x000000f4000000-0x000000f7ffffff
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0x5000-0x5fff]
pci_bus 0000:01: resource 1 mem: [0xf8000000-0xfbffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:02: resource 0 io: [0xa000-0xafff]
pci_bus 0000:02: resource 1 mem: [0xfdc00000-0xfdcfffff]
pci_bus 0000:02: resource 2 pref mem [0xfdb00000-0xfdbfffff]
pci_bus 0000:04: resource 0 io: [0x6000-0x6fff]
pci_bus 0000:04: resource 1 mem: [0xfde00000-0xfdefffff]
pci_bus 0000:04: resource 2 pref mem [0xfdd00000-0xfddfffff]
pci_bus 0000:05: resource 0 io: [0x7000-0x7fff]
pci_bus 0000:05: resource 1 mem: [0xd4000000-0xdbffffff]
pci_bus 0000:05: resource 2 pref mem [0xf4000000-0xf7ffffff]
pci_bus 0000:05: resource 3 io: [0x00-0xffff]
pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Scanning for low memory corruption every 60 seconds
HugeTLB registered 2 MB page size, pre-allocated 0 pages
SGI XFS with security attributes, realtime, large block/inode numbers, no debug enabled
msgmni has been set to 4020
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.3: setting latency timer to 64
lp: driver loaded but no devices found
Generic RTC Driver v1.07
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Platform driver 'serial8250' needs updating - please use dev_pm_ops
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
loop: module loaded
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x33 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part ems
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 17
ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 17
ata3: DUMMY
ata4: DUMMY
ata5: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 17
ata6: SATA max UDMA/133 abar m2048@0xfdffd000 port 0xfdffd380 irq 17
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
Platform driver 'i8042' needs updating - please use dev_pm_ops
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
cpuidle: using governor ladder
TCP cubic registered
NET: Registered protocol family 17
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
ata6: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATAPI: PIONEER DVD-RW DVR-212D, 1.21, max UDMA/66
ata5.00: configured for UDMA/66
ata2.00: ATA-7: ST3750640NS, 3.BAF, max UDMA/133
ata2.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: ATA-7: ST3750640NS, 3.BAF, max UDMA/133
ata1.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3750640NS 3.BA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB)
scsi 1:0:0:0: Direct-Access ATA ST3750640NS 3.BA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sdb] 1465149168 512-byte logical blocks: (750 GB/698 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdb1
scsi 4:0:0:0: CD-ROM PIONEER DVD-RW DVR-212D 1.21 PQ: 0 ANSI: 5
sdb2
sda:
sd 1:0:0:0: [sdb] Attached SCSI disk
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sda1 sda2
sr 4:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: [sda] Attached SCSI disk
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 2 and added 2 devices.
md: autorun ...
md: considering sda2 ...
md: adding sda2 ...
md: adding sdb2 ...
md: created md0
md: bind<sdb2>
md: bind<sda2>
md: running: <sda2><sdb2>
raid0: looking at sda2
raid0: comparing sda2(1433013760)
with sda2(1433013760)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sdb2
raid0: comparing sdb2(1433013760)
with sda2(1433013760)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 2866027520 sectors.
******* md0 configuration *********
zone0=[sda2/sdb2/]
zone offset=0kb device offset=0kb size=1433013760kb
**********************************
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
Freeing unused kernel memory: 352k freed
fuse init (API version 7.12)
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
md0:
ACPI: Invalid PBLK length [0]
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU0._PDC] (Node ffff88007f858490), AE_ALREADY_EXISTS
ACPI: Marking method _PDC as Serialized because of AE_ALREADY_EXISTS error unknown partition table
processor LNXCPU:00: registered as cooling_device0
input: Power Button as /class/input/input0
ACPI: Power Button [PWRF]
ACPI: Invalid PBLK length [0]
input: Power Button as /class/input/input1
ACPI: Power Button [PWRB]
ACPI: SSDT 000000007fee8750 000CE (v01 PmRef Cpu1Ist 00003000 INTL 20041203)
processor LNXCPU:01: registered as cooling_device1
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (34 C)
fan PNP0C0B:00: registered as cooling_device2
ACPI: Fan [FAN] (on)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sky2 driver version 1.23
sky2 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
sky2 0000:04:00.0: setting latency timer to 64
sky2 0000:04:00.0: Yukon-2 EC Ultra chip revision 2
sky2 eth0: addr 00:15:58:8a:ae:e5
firewire_ohci 0000:05:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
firewire_ohci 0000:05:00.0: setting latency timer to 64
firewire_ohci: Added fw-ohci device 0000:05:00.0, OHCI version 1.10
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000fc00
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
sr 4:0:0:0: Attached scsi generic sg2 type 5
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31-rc3-git4 uhci_hcd
usb usb1: SerialNumber: 0000:00:1a.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000f800
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31-rc3-git4 uhci_hcd
usb usb2: SerialNumber: 0000:00:1a.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000f400
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.31-rc3-git4 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000f000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.31-rc3-git4 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.31-rc3-git4 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.2
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdfff000
Linux video capture interface: v2.00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: EHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.31-rc3-git4 ehci_hcd
usb usb6: SerialNumber: 0000:00:1a.7
usb usb6: configuration #1 chosen from 1 choice
ivtv: Start initialization, version 1.4.1
ivtv0: Initializing card 0
ivtv0: Autodetected Hauppauge card (cx23416 based)
ivtv 0000:05:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
tveeprom 0-0050: Hauppauge model 32062, rev B185, serial# 2842715
cx18: Start initialization, version 1.2.0
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdffe000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: EHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.31-rc3-git4 ehci_hcd
usb usb7: SerialNumber: 0000:00:1d.7
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
firewire_core: created device fw0: GUID 00016c200022ce9e, S400
tveeprom 0-0050: tuner model is TCL 2002N 6A (idx 85, type 50)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is MSP3445 (idx 12)
tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
tveeprom 0-0050: has no radio, has IR receiver, has no IR transmitter
ivtv0: Autodetected Hauppauge WinTV PVR-250
saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0)
msp3400 0-0040: MSP3445G-B8 found @ 0x80 (ivtv i2c driver #0)
msp3400 0-0040: msp3400 supports radio, mode is autodetect and autoselect
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tuner-simple 0-0061: creating new instance
tuner-simple 0-0061: type set to 50 (TCL 2002N)
IRQ 17/ivtv0: IRQF_DISABLED is not guaranteed on shared IRQs
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Initialized card: Hauppauge WinTV PVR-250
cx18-0: Initializing card 0
cx18-0: Autodetected Hauppauge card
cx18 0000:05:03.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ivtv: End initialization
cx18-0: Unreasonably low latency timer, setting to 64 (was 2)
cx18-0: cx23418 revision 01010000 (B)
tveeprom 1-0050: Hauppauge model 74551, rev C1A3, serial# 1752579
tveeprom 1-0050: MAC address is 00-0D-FE-1A-BE-03
tveeprom 1-0050: tuner model is TCL MFNM05-4 (idx 103, type 43)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is CX23418 (idx 38)
tveeprom 1-0050: decoder processor is CX23418 (idx 31)
tveeprom 1-0050: has radio
cx18-0: Autodetected Hauppauge HVR-1600
cx18-0: Simultaneous Digital and Analog TV capture supported
IRQ 18/cx18-0: IRQF_DISABLED is not guaranteed on shared IRQs
tuner 2-0043: chip found @ 0x86 (cx18 i2c driver #0-1)
tda9887 2-0043: creating new instance
tda9887 2-0043: tda988[5/6/7] found
tuner 2-0061: chip found @ 0xc2 (cx18 i2c driver #0-1)
cs5345 1-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
tuner-simple 2-0061: creating new instance
tuner-simple 2-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F))
cx18-0: Registered device video1 for encoder MPEG (64 x 32 kB)
DVB: registering new adapter (cx18)
usb 7-5: new high speed USB device using ehci_hcd and address 4
MXL5005S: Attached at address 0x63
DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
cx18-0: DVB Frontend registered
cx18-0: Registered DVB adapter0 for TS (32 x 32 kB)
cx18-0: Registered device video33 for encoder YUV (16 x 128 kB)
cx18-0: Registered device vbi1 for encoder VBI (20 x 51984 bytes)
cx18-0: Registered device video25 for encoder PCM audio (256 x 4 kB)
cx18-0: Registered device radio1 for encoder radio
cx18-0: Initialized card: Hauppauge HVR-1600
cx18: End initialization
usb 7-5: New USB device found, idVendor=058f, idProduct=6254
usb 7-5: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 7-5: configuration #1 chosen from 1 choice
hub 7-5:1.0: USB hub found
hub 7-5:1.0: 4 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: New USB device found, idVendor=15c2, idProduct=ffdc
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-1: configuration #1 chosen from 1 choice
usb 3-2: new low speed USB device using uhci_hcd and address 2
usb 3-2: New USB device found, idVendor=046d, idProduct=c51e
usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: HID 046d:c51e as /class/input/input2
generic-usb 0003:046D:C51E.0001: input: USB HID v1.11 Keyboard [HID 046d:c51e] on usb-0000:00:1d.0-2/input0
input: HID 046d:c51e as /class/input/input3
generic-usb 0003:046D:C51E.0002: input,hiddev0: USB HID v1.11 Mouse [HID 046d:c51e] on usb-0000:00:1d.0-2/input1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 4-2: new full speed USB device using uhci_hcd and address 2
usb 4-2: New USB device found, idVendor=0403, idProduct=6001
usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-2: Product: Frankenswitch Solenoid Controller
usb 4-2: Manufacturer: RTR
usb 4-2: SerialNumber: A4RGYNGQ
usb 4-2: configuration #1 chosen from 1 choice
usb 5-2: new low speed USB device using uhci_hcd and address 2
usb 5-2: New USB device found, idVendor=051d, idProduct=0002
usb 5-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
usb 5-2: Product: Back-UPS XS 1300 LCD FW:836.H8 .D USB FW:H8
usb 5-2: Manufacturer: American Power Conversion
usb 5-2: SerialNumber: BB0820009163
usb 5-2: configuration #1 chosen from 1 choice
generic-usb 0003:051D:0002.0003: hiddev1: USB HID v1.10 Device [American Power Conversion Back-UPS XS 1300 LCD FW:836.H8 .D USB FW:H8 ] on usb-0000:00:1d.2-2/input0
usb 7-5.3: new high speed USB device using ehci_hcd and address 6
usb 7-5.3: New USB device found, idVendor=2040, idProduct=7200
usb 7-5.3: New USB device strings: Mfr=1, Product=2, SerialNumber=10
usb 7-5.3: Product: WinTV HVR-950
usb 7-5.3: Manufacturer: Hauppauge
usb 7-5.3: SerialNumber: 4031688744
usb 7-5.3: configuration #1 chosen from 1 choice
au0828 driver loaded
au0828: i2c bus registered
tveeprom 3-0050: Hauppauge model 72001, rev B3F0, serial# 5156904
tveeprom 3-0050: MAC address is 00-0D-FE-4E-B0-28
tveeprom 3-0050: tuner model is Xceive XC5000 (idx 150, type 76)
tveeprom 3-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88)
tveeprom 3-0050: audio processor is AU8522 (idx 44)
tveeprom 3-0050: decoder processor is AU8522 (idx 42)
tveeprom 3-0050: has no radio, has IR receiver, has no IR transmitter
hauppauge_eeprom: hauppauge eeprom: model=72001
au8522 3-0047: creating new instance
au8522_decoder creating new instance...
tuner 3-0061: chip found @ 0xc2 (au0828)
xc5000 3-0061: creating new instance
xc5000: Successfully identified at address 0x61
xc5000: Firmware has not been loaded previously
au8522 3-0047: attaching existing instance
xc5000 3-0061: attaching existing instance
xc5000: Successfully identified at address 0x61
xc5000: Firmware has not been loaded previously
DVB: registering new adapter (au0828)
DVB: registering adapter 1 frontend 0 (Auvitek AU8522 QAM/8VSB Frontend)...
Registered device AU0828 [Hauppauge HVR950Q]
usbcore: registered new interface driver au0828
usbcore: registered new interface driver snd-usb-audio
Adding 16064960k swap on /dev/sdb1. Priority:-1 extents:1 across:16064960k
EXT3 FS on sda1, internal journal
Filesystem "md0": Disabling barriers, trial barrier write failed
XFS mounting filesystem md0
Ending clean XFS mount for filesystem: md0
sky2 eth0: enabling interface
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
warning: `ntpd' uses 32-bit capabilities (legacy support in use)
ata1.00: configured for UDMA/133
ata1: EH complete
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata2.00: configured for UDMA/133
ata2: EH complete
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
cx18 0000:05:03.0: firmware: requesting v4l-cx23418-cpu.fw
cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
cx18 0000:05:03.0: firmware: requesting v4l-cx23418-apu.fw
cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
cx18 0000:05:03.0: firmware: requesting v4l-cx23418-cpu.fw
cx18 0000:05:03.0: firmware: requesting v4l-cx23418-apu.fw
cx18 0000:05:03.0: firmware: requesting v4l-cx23418-dig.fw
cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
ivtv 0000:05:02.0: firmware: requesting v4l-cx2341x-enc.fw
ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039
input: i2c IR (Hauppauge) as /class/input/input4
ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [ivtv i2c driver #0]
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)...
usb 7-5.3: firmware: requesting dvb-fe-xc5000-1.6.114.fw
xc5000: firmware read 12401 bytes.
xc5000: firmware uploading...
ata2.00: configured for UDMA/133
ata2: EH complete
ata1.00: configured for UDMA/133
ata1: EH complete
xc5000: firmware upload complete...
nvidia: module license 'NVIDIA' taints kernel.
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.14 Wed May 27 01:23:47 PDT 2009
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.14 Wed May 27 01:23:47 PDT 2009
input: i2c IR (Hauppauge) as /class/input/input5
ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [ivtv i2c driver #0]
input: i2c IR (Hauppauge) as /class/input/input6
ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [ivtv i2c driver #0]
xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)...
usb 7-5.3: firmware: requesting dvb-fe-xc5000-1.6.114.fw
xc5000: firmware read 12401 bytes.
xc5000: firmware uploading...
xc5000: firmware upload complete...
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
