Hi Hermann, On Tue, Jun 30, 2009 at 1:17 AM, hermann pitton<hermann-pitton@xxxxxxxx> wrote: > > Am Dienstag, den 30.06.2009, 01:17 +0200 schrieb hermann pitton: >> Hi Richard, >> >> Am Montag, den 29.06.2009, 22:43 +0100 schrieb Richard Smith: >> > Hi, >> > I bought a Compro Videomate S350 DVB-S card a few weeks ago as it was >> > cheap and looked like it might work with Linux using Jan Louw's >> > patches. However, my S350 seems to be slightly different - it uses a >> > SAA7135 chip so isn't correctly identified. Changing the PCI Vendor >> > ID to 0x7133 in the S350 patch fixed this, but unfortunately this is >> > the same PCI Vendor / Device / subvendor / subdevice as the Compro >> > Videomate T750 - an entirely different, DVB-T board. I'm not sure how >> > these should be told apart - maybe using eeprom content? >> > Anyway, once this was updated the card still didn't work. I realised >> > there was no voltage on the RF input to power the LNB, so by trial and >> > error found a GPIO bit that appears to turn LNB voltage on and off. >> > Instead of 0x8000 used in Jan's patch, use 0xC000 for GPIO setup. > > Likely more comes up, but forgot to ask already if 0x4000 is enough? No, with 0x4000 only the demodulator doesn't respond to I2C - I assume it is in sleep mode. Regards, Richard. > > Cheers, > Hermann > >> > With this change the card appears to work, at least receiving DVB-S. >> > I haven't tested the IR remote control or analogue inputs. >> > I hope this info is of some use to somebody, and that it's considered >> > if the S350 support gets added to v4l-dvb tree. I'm not sure if my >> > card is rare, or a sign of things to come. >> > >> > Here is the kernel log after modifying the driver: >> > >> > saa7133[0]: found at 0000:04:09.0, rev: 209, irq: 5, latency: 64, >> > mmio: 0xfaafe800 >> > saa7133[0]: subsystem: 185b:c900, board: Compro VideoMate S350/300 >> > [card=169,autodetected] >> > saa7133[0]: board init: gpio is 843f00 >> > saa7133[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 >> > saa7133[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom 20: 01 40 01 02 02 01 03 01 08 ff 00 87 ff ff ff ff >> > saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom 40: ff d6 00 c0 86 1c 02 01 02 ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff cb >> > saa7133[0]: i2c eeprom 60: 35 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom 70: 00 00 00 01 40 2a ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > saa7133[0]: registered device video0 [v4l2] >> > saa7133[0]: registered device vbi0 >> > dvb_init() allocating 1 frontend >> > DVB: registering new adapter (saa7133[0]) >> > DVB: registering adapter 0 frontend 0 (Zarlink ZL10313 DVB-S)... >> > >> > Regards, >> > >> > Richard Smith. >> >> good work! >> >> Compro has a lot of different cards with the same PCI subsystem (: >> >> And you are right, we can't make a difference to the T750 by that, since >> it also uses what is subsumed under the saa7133 chips. (saa7133/35/31e) >> >> Nothing left to detect than use some byte from the eeprom, even the not >> yet used board init for both is the same, might be different on the >> T750. >> >> > saa7130[0]: board init: gpio is 843f00 >> >> > saa7130[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 >> > > saa7130[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom 20: 01 40 01 02 02 01 03 01 08 ff 00 87 ff ff ff ff >> > > saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom 40: ff d6 00 c0 86 1c 02 01 02 ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff cb >> > > saa7130[0]: i2c eeprom 60: 30 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom 70: 00 00 00 10 03 9c ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> > > saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >> >> >From the Compro T750. >> >> [ 13.317113] saa7130/34: v4l2 driver version 0.2.14 loaded >> [ 13.317703] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 >> [ 13.317709] saa7134 0000:04:08.0: PCI INT A -> Link[APC1] -> GSI 16 >> (level, low) -> IRQ 16 >> [ 13.317716] saa7133[0]: found at 0000:04:08.0, rev: 209, irq: 16, >> latency: 32, mmio: 0xfdbfe000 >> [ 13.317723] saa7133[0]: subsystem: 185b:c900, board: Compro VideoMate >> T750 [card=139,autodetected] >> [ 13.317734] saa7133[0]: board init: gpio is 84bf00 >> [ 13.317746] saa7133[0]: Oops: IR config error [card=139] >> [ 13.476035] saa7133[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9 >> 1c 55 d2 b2 92 >> [ 13.476046] saa7133[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476055] saa7133[0]: i2c eeprom 20: 01 40 01 02 02 01 03 01 08 ff 00 >> 87 ff ff ff ff >> [ 13.476064] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476072] saa7133[0]: i2c eeprom 40: ff d7 00 c4 86 1e 05 ff 02 c2 ff >> 01 c6 ff 05 ff >> [ 13.476081] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff cb >> [ 13.476089] saa7133[0]: i2c eeprom 60: 35 ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476098] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476106] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476115] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476123] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476132] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476140] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476149] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476157] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> [ 13.476166] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff >> ff ff ff ff ff >> >> Seems we could use byte 0x41 like on the other Compro cards. >> >> Tuner type is 0xd6 versus 0xd7 on the T750, also tuner address is 0xc0 >> versus 0xc4 and digital demod is 0x1c versus 0x1e. (not shifted >> 1) >> >> Igor received also a patch for remote support on the S350. >> >> Without looking into any further details yet, might me more to consider, >> but maybe that IR patch works on recent Compro cards like the T750 too. >> > > > -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
