Hi,
Is this ready to get merged or still require discussion before merge?
Murali Karicheri
Software Design Engineer
Texas Instruments Inc.
Germantown, MD 20874
email: m-karicheri2@xxxxxx
>-----Original Message-----
>From: Karicheri, Muralidharan
>Sent: Wednesday, June 17, 2009 5:17 PM
>To: linux-media@xxxxxxxxxxxxxxx
>Cc: davinci-linux-open-source@xxxxxxxxxxxxxxxxxxxx; Muralidharan Karicheri;
>Karicheri, Muralidharan
>Subject: [PATCH] adding support for setting bus parameters in sub device
>
>From: Muralidharan Karicheri <a0868495@xxxxxxxxxxxxxxxxxxxxxxxxxx>
>
>This patch adds support for setting bus parameters such as bus type
>(Raw Bayer or Raw YUV image data bus), bus width (example 10 bit raw
>image data bus, 10 bit BT.656 etc.), and polarities (vsync, hsync, field
>etc) in sub device. This allows bridge driver to configure the sub device
>bus for a specific set of bus parameters through s_bus() function call.
>This also can be used to define platform specific bus parameters for
>host and sub-devices.
>
>Reviewed by: Hans Verkuil <hverkuil@xxxxxxxxx>
>Signed-off-by: Murali Karicheri <m-karicheri2@xxxxxx>
>---
>Applies to v4l-dvb repository
>
> include/media/v4l2-subdev.h | 40
>++++++++++++++++++++++++++++++++++++++++
> 1 files changed, 40 insertions(+), 0 deletions(-)
>
>diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
>index 1785608..8532b91 100644
>--- a/include/media/v4l2-subdev.h
>+++ b/include/media/v4l2-subdev.h
>@@ -37,6 +37,43 @@ struct v4l2_decode_vbi_line {
> u32 type; /* VBI service type (V4L2_SLICED_*). 0 if no
>service found */
> };
>
>+/*
>+ * Some sub-devices are connected to the host/bridge device through a bus
>that
>+ * carries the clock, vsync, hsync and data. Some interfaces such as
>BT.656
>+ * carries the sync embedded in the data where as others have separate
>line
>+ * carrying the sync signals. The structure below is used to define bus
>+ * configuration parameters for host as well as sub-device
>+ */
>+enum v4l2_bus_type {
>+ /* Raw YUV image data bus */
>+ V4L2_BUS_RAW_YUV,
>+ /* Raw Bayer image data bus */
>+ V4L2_BUS_RAW_BAYER
>+};
>+
>+struct v4l2_bus_settings {
>+ /* yuv or bayer image data bus */
>+ enum v4l2_bus_type type;
>+ /* subdev bus width */
>+ u8 subdev_width;
>+ /* host bus width */
>+ u8 host_width;
>+ /* embedded sync, set this when sync is embedded in the data stream
>*/
>+ unsigned embedded_sync:1;
>+ /* master or slave */
>+ unsigned host_is_master:1;
>+ /* 0 - active low, 1 - active high */
>+ unsigned pol_vsync:1;
>+ /* 0 - active low, 1 - active high */
>+ unsigned pol_hsync:1;
>+ /* 0 - low to high , 1 - high to low */
>+ unsigned pol_field:1;
>+ /* 0 - active low , 1 - active high */
>+ unsigned pol_data:1;
>+ /* 0 - sample at falling edge , 1 - sample at rising edge */
>+ unsigned edge_pclock:1;
>+};
>+
> /* Sub-devices are devices that are connected somehow to the main bridge
> device. These devices are usually audio/video muxers/encoders/decoders
>or
> sensors and webcam controllers.
>@@ -199,6 +236,8 @@ struct v4l2_subdev_audio_ops {
>
> s_routing: see s_routing in audio_ops, except this version is for video
> devices.
>+
>+ s_bus: set bus parameters in sub device to configure the bus
> */
> struct v4l2_subdev_video_ops {
> int (*s_routing)(struct v4l2_subdev *sd, u32 input, u32 output, u32
>config);
>@@ -219,6 +258,7 @@ struct v4l2_subdev_video_ops {
> int (*s_parm)(struct v4l2_subdev *sd, struct v4l2_streamparm *param);
> int (*enum_framesizes)(struct v4l2_subdev *sd, struct
>v4l2_frmsizeenum *fsize);
> int (*enum_frameintervals)(struct v4l2_subdev *sd, struct
>v4l2_frmivalenum *fival);
>+ int (*s_bus)(struct v4l2_subdev *sd, const struct v4l2_bus_settings
>*bus);
> };
>
> struct v4l2_subdev_ops {
>--
>1.6.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
