On Thursday 11 June 2009 23:38:17 Udo A. Steinberg wrote: > On Thu, 11 Jun 2009 22:18:10 +0200 Hans Verkuil (HV) wrote: > > HV> On Thursday 11 June 2009 22:14:02 Udo A. Steinberg wrote: > HV> > Hi all, > HV> > > HV> > With Linux 2.6.30 the BTTV driver for my WinTV card claims > HV> > > HV> > bttv0: audio absent, no audio device found! > HV> > > HV> > and audio does not work. This worked up to and including 2.6.29. Is > HV> > this a known issue? Does anyone have a fix or a patch for me to try? > HV> > HV> You've no doubt compiled the bttv driver into the kernel and not as a > HV> module. > HV> > HV> I've just pushed a fix for this to my tree: > HV> http://www.linuxtv.org/hg/~hverkuil/v4l-dvb > > Yes, I've compiled bttv into the kernel. I've (hopefully correctly) ported > the commit http://www.linuxtv.org/hg/~hverkuil/v4l-dvb/rev/820630b2b12f > to 2.6.30. Now I'm getting: > > bttv: driver version 0.9.18 loaded > bttv: using 8 buffers with 2080k (520 pages) each for capture > bttv: Bt8xx card found (0). > bttv 0000:06:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 > bttv0: Bt878 (rev 2) at 0000:06:00.0, irq: 21, latency: 32, mmio: 0x50001000 > bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb > bttv0: using: Hauppauge (bt878) [card=10,autodetected] > IRQ 21/bttv0: IRQF_DISABLED is not guaranteed on shared IRQs > bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init] > bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] > ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-1/1-0018/ir0 [bt878 #0 [sw]] > i2c-adapter i2c-1: sendbytes: NAK bailout. > tveeprom 1-0050: Huh, no eeprom present (err=-5)? > tveeprom 1-0050: Encountered bad packet header [00]. Corrupt or not a Hauppauge eeprom. > bttv0: Hauppauge eeprom indicates model#0 > bttv0: tuner absent > bttv0: registered device video0 > bttv0: registered device vbi0 > bttv0: PLL: 28636363 => 35468950 Hmm, my patch needs a bit more work. But to get your setup working try to revert the change you made and do just this: Go to drivers/media/video/Makefile and move this line: obj-$(CONFIG_VIDEO_MSP3400) += msp3400.o in front of this line: obj-$(CONFIG_VIDEO_BT848) += bt8xx/ Recompile and see if that is working. I got the tveeprom error as well when I tested with ivtv, but I thought that had something to do with the ivtv driver. Apparently not, so I need to dig a bit more into these dependencies. Regards, Hans -- Hans Verkuil - video4linux developer - sponsored by TANDBERG Telecom -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
