From: Muralidharan Karicheri <a0868495@xxxxxxxxxxxxxxxxxxxxxxxxxx>
DM355 platform and board setup
This has platform and board setup changes to support vpfe capture
driver for DM355 EVMs.
This has comments incorporated from previous review.
Reviewed By "Hans Verkuil".
Reviewed By "Laurent Pinchart".
Signed-off-by: Muralidharan Karicheri <m-karicheri2@xxxxxx>
---
Applies to Davinci GIT Tree
arch/arm/mach-davinci/board-dm355-evm.c | 72 ++++++++++++++++++++++++++-
arch/arm/mach-davinci/dm355.c | 65 +++++++++++++++++++++++++
arch/arm/mach-davinci/include/mach/dm355.h | 2 +
arch/arm/mach-davinci/include/mach/mux.h | 9 ++++
4 files changed, 145 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c
index f32e3d8..3a3f5e0 100644
--- a/arch/arm/mach-davinci/board-dm355-evm.c
+++ b/arch/arm/mach-davinci/board-dm355-evm.c
@@ -20,6 +20,8 @@
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/clk.h>
+#include <linux/videodev2.h>
+#include <media/tvp514x.h>
#include <linux/spi/spi.h>
#include <linux/spi/eeprom.h>
@@ -134,12 +136,23 @@ static void dm355evm_mmcsd_gpios(unsigned gpio)
dm355evm_mmc_gpios = gpio;
}
+#define TVP5146_I2C_ADDR 0x5D
+static struct tvp514x_platform_data tvp5146_pdata = {
+ .clk_polarity = 0,
+ .hs_polarity = 1,
+ .vs_polarity = 1
+};
+
static struct i2c_board_info dm355evm_i2c_info[] = {
- { I2C_BOARD_INFO("dm355evm_msp", 0x25),
+ { I2C_BOARD_INFO("dm355evm_msp", 0x25),
.platform_data = dm355evm_mmcsd_gpios,
- /* plus irq */ },
+ },
+ {
+ I2C_BOARD_INFO("tvp5146", TVP5146_I2C_ADDR),
+ .platform_data = &tvp5146_pdata,
+ },
+ /* { plus irq }, */
/* { I2C_BOARD_INFO("tlv320aic3x", 0x1b), }, */
- /* { I2C_BOARD_INFO("tvp5146", 0x5d), }, */
};
static void __init evm_init_i2c(void)
@@ -178,6 +191,57 @@ static struct platform_device dm355evm_dm9000 = {
.num_resources = ARRAY_SIZE(dm355evm_dm9000_rsrc),
};
+#define TVP514X_STD_ALL (V4L2_STD_NTSC | V4L2_STD_PAL)
+/* Inputs available at the TVP5146 */
+static struct v4l2_input tvp5146_inputs[] = {
+ {
+ .index = 0,
+ .name = "COMPOSITE",
+ .type = V4L2_INPUT_TYPE_CAMERA,
+ .std = TVP514X_STD_ALL,
+ },
+ {
+ .index = 1,
+ .name = "SVIDEO",
+ .type = V4L2_INPUT_TYPE_CAMERA,
+ .std = TVP514X_STD_ALL,
+ },
+};
+
+/*
+ * this is the route info for connecting each input to decoder
+ * ouput that goes to vpfe. There is a one to one correspondence
+ * with tvp5146_inputs
+ */
+static struct v4l2_routing tvp5146_routes[] = {
+ {
+ .input = INPUT_CVBS_VI2B,
+ .output = OUTPUT_10BIT_422_EMBEDDED_SYNC,
+ },
+ {
+ .input = INPUT_SVIDEO_VI2C_VI1C,
+ .output = OUTPUT_10BIT_422_EMBEDDED_SYNC,
+ },
+};
+
+static struct vpfe_subdev_info vpfe_sub_devs[] = {
+ {
+ .name = "tvp5146",
+ .grp_id = 0,
+ .num_inputs = ARRAY_SIZE(tvp5146_inputs),
+ .inputs = (struct v4l2_input *)tvp5146_inputs,
+ .routes = (struct v4l2_routing *)tvp5146_routes,
+ .can_route = 1,
+ }
+};
+
+static struct vpfe_config vpfe_cfg = {
+ .num_subdevs = ARRAY_SIZE(vpfe_sub_devs),
+ .sub_devs = vpfe_sub_devs,
+ .card_name = "DM355 EVM",
+ .ccdc = "DM355 CCDC",
+};
+
static struct platform_device *davinci_evm_devices[] __initdata = {
&dm355evm_dm9000,
&davinci_nand_device,
@@ -189,6 +253,8 @@ static struct davinci_uart_config uart_config __initdata = {
static void __init dm355_evm_map_io(void)
{
+ /* setup input configuration for VPFE input devices */
+ dm355_set_vpfe_config(&vpfe_cfg);
dm355_init();
}
diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c
index bccc5a8..9d80496 100644
--- a/arch/arm/mach-davinci/dm355.c
+++ b/arch/arm/mach-davinci/dm355.c
@@ -481,6 +481,14 @@ INT_CFG(DM355, INT_EDMA_TC1_ERR, 4, 1, 1, false)
EVT_CFG(DM355, EVT8_ASP1_TX, 0, 1, 0, false)
EVT_CFG(DM355, EVT9_ASP1_RX, 1, 1, 0, false)
EVT_CFG(DM355, EVT26_MMC0_RX, 2, 1, 0, false)
+
+MUX_CFG(DM355, VIN_PCLK, 0, 14, 1, 1, false)
+MUX_CFG(DM355, VIN_CAM_WEN, 0, 13, 1, 1, false)
+MUX_CFG(DM355, VIN_CAM_VD, 0, 12, 1, 1, false)
+MUX_CFG(DM355, VIN_CAM_HD, 0, 11, 1, 1, false)
+MUX_CFG(DM355, VIN_YIN_EN, 0, 10, 1, 1, false)
+MUX_CFG(DM355, VIN_CINL_EN, 0, 0, 0xff, 0x55, false)
+MUX_CFG(DM355, VIN_CINH_EN, 0, 8, 3, 3, false)
#endif
};
@@ -604,6 +612,47 @@ static struct platform_device dm355_edma_device = {
.resource = edma_resources,
};
+static struct resource vpfe_resources[] = {
+ {
+ .start = IRQ_VDINT0,
+ .end = IRQ_VDINT0,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_VDINT1,
+ .end = IRQ_VDINT1,
+ .flags = IORESOURCE_IRQ,
+ },
+ /* CCDC Base address */
+ {
+ .flags = IORESOURCE_MEM,
+ .start = 0x01c70600,
+ .end = 0x01c70600 + 0x1ff,
+ },
+ /* VPSS Base address */
+ {
+ .start = 0x01c70800,
+ .end = 0x01c70800 + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static u64 vpfe_capture_dma_mask = DMA_BIT_MASK(32);
+static struct platform_device vpfe_capture_dev = {
+ .name = CAPTURE_DRV_NAME,
+ .id = -1,
+ .num_resources = ARRAY_SIZE(vpfe_resources),
+ .resource = vpfe_resources,
+ .dev = {
+ .dma_mask = &vpfe_capture_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
+void dm355_set_vpfe_config(struct vpfe_config *cfg)
+{
+ vpfe_capture_dev.dev.platform_data = cfg;
+}
/*----------------------------------------------------------------------*/
static struct map_desc dm355_io_desc[] = {
@@ -718,13 +767,29 @@ void __init dm355_init(void)
davinci_common_init(&davinci_soc_info_dm355);
}
+#define DM355_VPSSCLK_CLKCTRL_REG 0x1c70004
static int __init dm355_init_devices(void)
{
+ void __iomem *base = IO_ADDRESS(DM355_VPSSCLK_CLKCTRL_REG);
+
if (!cpu_is_davinci_dm355())
return 0;
davinci_cfg_reg(DM355_INT_EDMA_CC);
platform_device_register(&dm355_edma_device);
+ /* setup clock for vpss modules */
+ __raw_writel(0x79, base);
+ /* setup Mux configuration for vpfe input and register
+ * vpfe capture platform device
+ */
+ davinci_cfg_reg(DM355_VIN_PCLK);
+ davinci_cfg_reg(DM355_VIN_CAM_WEN);
+ davinci_cfg_reg(DM355_VIN_CAM_VD);
+ davinci_cfg_reg(DM355_VIN_CAM_HD);
+ davinci_cfg_reg(DM355_VIN_YIN_EN);
+ davinci_cfg_reg(DM355_VIN_CINL_EN);
+ davinci_cfg_reg(DM355_VIN_CINH_EN);
+ platform_device_register(&vpfe_capture_dev);
return 0;
}
postcore_initcall(dm355_init_devices);
diff --git a/arch/arm/mach-davinci/include/mach/dm355.h b/arch/arm/mach-davinci/include/mach/dm355.h
index 54903b7..e28713c 100644
--- a/arch/arm/mach-davinci/include/mach/dm355.h
+++ b/arch/arm/mach-davinci/include/mach/dm355.h
@@ -12,11 +12,13 @@
#define __ASM_ARCH_DM355_H
#include <mach/hardware.h>
+#include <media/davinci/vpfe_capture.h>
struct spi_board_info;
void __init dm355_init(void);
void dm355_init_spi0(unsigned chipselect_mask,
struct spi_board_info *info, unsigned len);
+void dm355_set_vpfe_config(struct vpfe_config *cfg);
#endif /* __ASM_ARCH_DM355_H */
diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h
index 018701f..4516839 100644
--- a/arch/arm/mach-davinci/include/mach/mux.h
+++ b/arch/arm/mach-davinci/include/mach/mux.h
@@ -154,6 +154,15 @@ enum davinci_dm355_index {
DM355_EVT8_ASP1_TX,
DM355_EVT9_ASP1_RX,
DM355_EVT26_MMC0_RX,
+
+ /* Video In Pin Mux */
+ DM355_VIN_PCLK,
+ DM355_VIN_CAM_WEN,
+ DM355_VIN_CAM_VD,
+ DM355_VIN_CAM_HD,
+ DM355_VIN_YIN_EN,
+ DM355_VIN_CINL_EN,
+ DM355_VIN_CINH_EN,
};
#ifdef CONFIG_DAVINCI_MUX
--
1.6.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
